EVEN HEAT (G52229) Propane (G52230) Natural Gas

Transcription

1 DURILITY POWER PERFORMNCE EVEN HET barbecue with 4 burners ssemly MNUL (G52229) Propane (G52230) Natural Gas Limited 5-Year WRRNTY Read and save manual for future reference. ssemble your grill immediately. Missing or damaged parts should be claimed within 30 days of purchase. For product inquiries, parts, warranty and troubleshooting support, please call Manual Revision #: T

2 HEVY RTICLE NEEDS 2 TO LIFT THIS MNUL MUST REMIN WITH THE PRODUCT T LL TIMES To ORDER non-warranty replacement parts or accessories, or to register your warranty, please visit us on the web at CUTION Sharp edges. Wear gloves when assembling your grill. CUTION Read and follow all safety statements, assembly instructions, use and care directions before attempting to assemble and cook. INSTLLER OR SSEMLER/ CONSUMER This manual should be kept with the Q at all times. WRNING Failure to follow all of the Manufacturer s instructions could result in hazardous fires, explosions, property damage, or serious personal injury or even death. Follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. Do not try to light this barbecue without reading the Lighting Instructions section of this manual. DNGER 1. If you smell Gas: a. Shut off gas to the appliance b. Extinguish any open flame c. Open lid d. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department 2. Requires two people to complete the assembly process. 3. eware of sharp edges. WRNING 1. Do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance. 2. n LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WRNING IN DIRECT SUN, ND IN OPERTION, YOUR Q S STINLESS STEEL ND PINTED STEEL PRTS CN ECOME VERY HOT. THIS RECUE IS FOR OUTDOOR USE ONLY CONTCT CLL CENTRE IF NY PRTS RE MISSING

3 HRDWRE PCK TOOLS NEEDED FOR SSEMLY #2 Phillips screwdriver (long and short) ¼ Slotted screwdriver (long and short) djustable wrench Pliers For correct hardware assembly, always position the lock washer between the screw and the flat washer. Screw Lock Washer Flat Washer No. Description Part Number Qty. 1 ¼"-20UNCX38 Screw ¼"-20UNCX16 Screw φ7 Lock Washer φ7 Washer /4-20UNC Nut NO.10-24UNCx13 Screw φ5 Lock Washer φ5 Washer ST4.2x10 Tapping Screw NO.8-32UNCx10 Screw φ4 Lock Washer φ4 Washer Control Knob G522-C Wing Nut U Pin G Fiber Washer G Caution: Sheet metal can cause injury. Wear gloves when installing the grill /4-20UNCx38 Screw X 8 1/4-20UNCx16 Screw X 16 φ7 Lock Washer X φ7 Washer X 24 1/4-20UNC Nut X 6 NO.10-24UNCX13 Screw X φ5 Lock Washer X 10 φ5 Washer X 10 ST4.2x10 Tapping Screw X NO.8-32UNC x10 Screw X 4 φ4 Lock Washer X 4 φ4 Washer X Control Knob X 1 Wing Nut X 1 U Pin X 1 16 Fiber Washer X 6 EFORE SSEMLING THE RECUE, RED THESE INSTRUCTIONS CREFULLY. ssemble the barbecue on a flat, clean surface. Grill is heavy. You should have at least two people assemble the barbecue together. 1

4 PRTS LIST (PROPNE) FOR (G52229) Item No. Qty. Description Part No. 1 Top lid assembly G522-N Thermometer G C 2 Screw for top lid G D 2 Lid bumper, front G E 2 Lid bumper, rear G urner box assembly G522-N Even Heat burners G C 1 Carryover assembly G D 4 Even Heat heat distribution plate G E 3 Dual surface cooking grate G F 1 Warming rack G522-00D4-01 G 1 Match holder G C 1 Manifold assembly-lp G522-N C 1 Regulator G CC 1 Side burner valve with T bracket - LP G522-00G2-01 CD 1 Metal hose, side burner G CE1 1 Electronic ignition assembly G CE2 1 Ignition battery cover G CE3 1 Instastart ignition button G CF 4 Electrode set, main burner G CG 4 Control knob G CH 1 Control panel G522-00D6-01 CI 1 Front brace G CJ 1 Quick Clean grease tray G CK 1 Quick Clean grease cup G CL 1 Upper back panel G CM 1 Heat shield G CN 1 Right track G CO 1 Left track G CP 1 Door support rail G Item No. Qty. Description Part No. D 1 Left side burner side shelf G522-D D 1 Side burner drip pan G DC 1 Side burner G DD 1 Electrode Set, side burner G DE 1 Side burner lid G DF 1 Side burner cooking grate G DG 1 Right Side Shelf G522-D DH/ #13 1 Side burner control knob (#13) G522-C E 1 Left side panel G522-F E 1 Right side panel G EC 1 Left door assembly G ED 1 Right door assembly G EE 2 Door handle G EF 1 ottom shelf-lp G522-F EG 2 Locking castor G EH 2 Castor G EI 2 Door magnet assembly G501-00F2-01 EJ 1 Tank Exclusion G F1 1 Hardware Pack G F2 1 ssembly Manual G522-M F3 1 Safe Use and Care Manual G522-M F5 1 Tank screw G

5 EXPLODED DIGRM (PROPNE) FOR (G52229) CF C F D E E D DF CJ C CK DE DG DC D D CC CH DD DH CG CE3 CP EE EE C G CL ED EC CI CE2 CO CN CM CE1 CC CD E EJ C C E EH F5 EF EI EG Extras Hardware Pack ssembly Manual Safe Use & Care Manual F1 F2 F3 3

6 PRTS LIST (NTURL GS) FOR (G52230) Item No. Qty. Description Part No. 1 Top lid assembly G522-N Thermometer G C 2 Screw for top lid G D 2 Lid bumper, front G E 2 Lid bumper, rear G urner box assembly G522-N Even Heat burners G C 1 Carryover assembly G D 4 Even Heat heat distribution plate G E 3 Dual surface cooking grate G F 1 Warming rack G522-00D4-01 G 1 Match holder G C 1 Manifold assembly-ng G522-P C 1 Natural Gas hose G CC 1 Side burner valve with T bracket - NG G522-00G3-01 CD 1 Metal hose, side burner G CE1 1 Electronic ignition assembly G CE2 1 Ignition battery cover G CE3 1 Instastart ignition button G CF 4 Electrode set, main burner G CG 4 Control knob G CH 1 Control panel G522-00D6-01 CI 1 Front brace G CJ 1 Quick Clean grease tray G CK 1 Quick Clean grease cup G CL 1 Upper back panel G CM 1 Heat shield G CN 1 Right track G CO 1 Left track G CP 1 Door support rail G Item No. Qty. Description Part No. D 1 Left side burner side shelf G522-D D 1 Side burner drip pan G DC 1 Side burner G DD 1 Electrode Set, side burner G DE 1 Side burner lid G DF 1 Side burner cooking grate G DG 1 Right Side Shelf G522-D DH/ #13 1 Side burner control knob (#13) G522-C E 1 Left side panel G522-F E 1 Right side panel G EC 1 Left door assembly G ED 1 Right door assembly G EE 2 Door handle G EF 1 ottom shelf-ng G EG 2 Locking castor G EH 2 Castor G EI 2 Door magnet assembly G501-00F2-01 F1 1 Hardware pack G F2 1 ssembly manual G522-M F3 1 Safe use and care manual G522-M

7 EXPLODED DIGRM (NTURL GS) FOR (G52230) CF C F D E E C D DF CJ C CK DE DG DC D D CC CH DD DH CG CE3 CP EE EE G CL ED EC CI CE2 CO CN CM CE1 CD CC E E C EH EF EI EG Extras Hardware Pack ssembly Manual Safe Use & Care Manual F1 F2 F3 5

8 ssemly INSTRUCTIONS 1 EG EF EH a. Separate the 2 different types of castors: 2 locking castors (EG) and 2 regular castors (EH). Note: Regular castors (EH) need to be assembled to the front of the bottom shelf (EF), and locking castors (EG) need to be assembled to the back of the bottom shelf (EF), as shown in image. Upside down view EH b. Insert the U Pin (#15) into one of the regular castors (EH), as shown in image. ttach the regular castor (EH) to the front of the bottom shelf (EF), and use the U Pin (#15) to secure and tighten. 15 Close up Repeat for remaining 3 castors (EG & EH). 615 X 1 6

9 ssemly INSTRUCTIONS 2 Ensure that the locking castors (EG) are firmly locked in the ON position before continuing. E E ssemble the left side panel (E) and the right side panel (E), to the bottom shelf (EF) EF X 6 X 6 X 6 Front view E EF Close up 3 E CI ttach the front brace (CI) to the left and right cart side panels (E and E). The top of the front brace (CI) can be identified by two clips located on the top left, and right side of this part. E TIP: One person should align the left side, while the second person assembles the right side. ack view X 4 X 4 X 4 CI Close up 7

10 ssemly INSTRUCTIONS 4 THIS STEP REQUIRES 3 PEOPLE. DO NOT TTEMPT LONE. EXTREMELY HEVY. Position the top lid assembly and burner box assembly ( & ) onto the cart assembly (C), as shown. C Front view 5 CL ttach the upper back panel (CL) to both the left and right side panels (E & E). DO NOT tighten screws until all hardware has been positioned. E E ack view X 4 X 4 X 4 CL E Close up 8

11 ssemly INSTRUCTIONS 6 a. ssemble the left and right tracks (CO and CN) for the Quick Clean grease tray (CJ), as shown in figure. CO CN ack view b. oth the left and right tracks (CO and CN) should be inserted into the two clips located on the front brace (CI), as shown in figure. CI Close up, front view CN CL CO c. ssemble the back of the left and right tracks (CO and CN) to the upper back panel (CL), as shown in figure C C Close up, back view X 2 X 2 X 2 9

12 ssemly INSTRUCTIONS 7 TIP: Do not tighten until all hardware is in place. a. Mount the right side shelf (DG) onto the two support brackets, located on the right, upper side panel of the burner box (). DG Front view b. ssemble the front of the right side shelf (DG) to the control panel (CH), as shown in figure. CH Front, right side view DG X 2 X 2 X 2 DG c. ssemble the right side shelf (DG) to the upper side panel of the burner box (), by positioning hardware through the interior of the burner box, as shown in figure C C View inside burner box CH X 2 X 2 X 2 X 2 d. Complete the right side shelf assembly (DG) by connecting the right side shelf (DG) to the rear of the burner box side panel () as shown in figure D. DG D ack, right side view X 1 X 1 X 1 X 1 10

13 ssemly INSTRUCTIONS 8 D DG TIP: Do not tighten until all hardware is in place. a. Mount the left side burner side shelf (D) onto the two support brackets, located on the left, upper side panel of the burner box (). Front view b. ssemble the front of the left side burner side shelf assembly (D) to the control panel (CH), as shown in figure D CH X 2 X 2 X 2 Front, left side view c. ssemble the left side burner side shelf (D) to the upper side panel of the burner box (), by positioning hardware through the interior of the burner box (), as shown in figure C D C View inside burner box X 2 X 2 X 2 X 2 d. Complete the left side burner side shelf assembly (D) by connecting the side shelf to the rear of the burner box side panel (), as shown in figure D. D D ack view X 1 X 1 X 1 X 1 11

14 ssemly INSTRUCTIONS 9 a. Remove the hardware that is pre-assembled to the side burner valve (CC). Feed the side burner valve (CC) through the bottom of the left side burner side shelf (D), and re-attach the hardware, as shown. CC D Front, left side view b. ssemble the side burner control knob (#13) to the side burner valve (CC) CC X 1 c. Position the side burner (DC) through the opening in the side burner drip pan (D). DC C D Front, left side view d. Make sure that the side burner (DC) engages the side burner valve (CC), as shown in figure D. DC CC D Left side view 12

15 ssemly INSTRUCTIONS 9 D e. Using the wing nut (#14), assemble the side burner (DC) to the side burner drip pan (D), as shown. DC DD E DF X 1 f. Locate the side burner electrode wire (DD) and insert into the base of the side burner electrode (DC), as shown in figure E. g. Position the side burner cooking grate (DF) onto the side burner drip pan (D). F D 10 a. Remove the ignition battery cover (CE2) and the plastic nut from the electronic ignition box (CE1). CE1 CE2 b. Position the electronic ignition box (CE1) into the heat shield (CE1) and feed the assembly through the opening in the right side panel (E) and secure using the nut. E - + CE2 c. Insert one battery into the battery compartment with the positive end facing outward, as shown. Secure using the ignition button cover (CE2). 13

16 ssemly INSTRUCTIONS Electronic Ignition: Electrode SSEMLY 10 TIP: The Electrode Set, main burner (CF) and the Electrode wire, side burner (DD), can be found attached to the control panel (CH) heat shield, as shown in figure C. CH C DD Control panel, right side CF d. Insert the four Electrode set, main burner (CF) wires into the Electronic ignition assembly (CE1) as shown in figure D. CF CE1 CF D e. Insert the Electrode wire, side burner (DD) into the Electronic ignition assembly (CE1), as shown in figure E. CE1 E DD f. Insert the two Instastart ignition button (CE3) wires into the Electronic ignition assembly (CE1), as shown in figure F. CE1 F CE3 14

17 ssemly INSTRUCTIONS 11 a. ssemble the heat shield (CM) to the bottom of the front brace (CI) as shown in figure. CI 9 Front view CM CM X 2 b. ssemble the back of the heatshield (CM) to the upper back panel (CL), as shown in figure. 9 CL ack view X 2 12 EJ PROPNE MODEL ONLY a. ssemble the tank exclusion (EJ) to the bottom shelf (EF), as shown in figure. EF EJ X 2 X 2 X 2 b. ssemble the tank exclusion (EJ) to the right cart side panel (E), as shown in figure C. EF E X 2 X 2 X 2 C 15

18 ssemly INSTRUCTIONS 13 E Front, left side view CP E ssemble the door support rail (CP) to the left and right upper side panels (E and E), as shown. WRNING: This part may have sharp edges. Wear protective gloves when assembling X 4 X 4 X 4 CH E Close up, front view CP 14 EE ssemble the door handle (EE) to the left and right door assembly (EC and ED) as shown in figure and. EC X 4 X 4 X 4 EE EC 16

19 ssemly INSTRUCTIONS 15 CP PROPNE MODEL SHOWN a. ssemble the right door assembly (ED), to the bottom shelf (EF) by inserting the fixed pin (bottom of door) into the hole provided (figure ). ED EF E EF ottom of door ED b. ssemble the top of the door assembly (ED) to the door support rail (CP), by pressing in the door support pin and aligning with the hole located on the top right corner of the door. C Top of door CP ED TIP: Use a paint scraper to press-in the support pin, while the second person aligns the door. The support pin will lock into position when the door is assembled correctly. c. Repeat steps a, and b for the left door assembly (EC). 17

20 ssemly INSTRUCTIONS 16 D Position the Even Heat TM heat distribution plates (D) into the burner box () as shown. D Close up, front view D Close up, back view 17 a. Position the Quick Clean TM grease tray (CJ) onto the right and left tracks (CN and CO), as shown. CJ CK b. Position the Quick Clean grease cup (CK) in position under the under the Quick Clean grease tray (CJ). ack view 18

21 ssemly INSTRUCTIONS 18 F E a. ssemble the warming rack (F) by inserting the three fixed pins into the three holes provided on the burner box back panel (), as shown in Figure. b. Place the cooking grates (E) into the burner box (), as shown in figure. 19 For propane model only. For natural gas model, follow step 20. a. Feed the regulator (C) through the opening on the left side panel (E). b. Position the 20 lb propane tank onto the bottom shelf (EF), and secure using the tank screw (F5) (already attached) located on the underside of the bottom shelf, as shown in figure. EF F5 CI c. ttach the regulator (C) coupling nut to the propane cylinder valve. E C TTENTION: DO NOT STORE EXTR PROPNE TNKS WITHIN Q CRT. C 19

22 ssemly INSTRUCTIONS 20 For natural gas model only. ttach the natural gas hose (C) to the side burner valve (CC), as shown. CC C TTENTION: In order to complete installation of your Natural Gas Q a ½ or 3/8 adapter may be required to connect your Q s Natural gas hose to your home gas supply. Contact your natural gas supplier to purchase the necessary part. NOTE: EXTR HRDWRE WILL E LEFT OVER FOR NTURL GS MODEL. 20

23 DDITIONL WRNINGS You have now completed the ssembly of your COLEMN EVEN HET RECUE. NEXT STEPS: 1. Position your RECUE 2. Read SFE USE & CRE MNUL 3. Perform Grill Safety Check-list WRNING: FOR YOUR FMILIES SFETY, DO NOT TTEMPT TO LIGHT THIS Q UNTIL YOU HVE REVIEWED PGES 4-7 OF THE COLEMN SFE USE & CRE MNUL. LL SFETY ND LEK TESTS MUST E PERFORMED Y THE END USER, PRIOR TO LIGHTING THIS Q. WRNING HOT SURFCES:!!! POSITION YOUR RECUE lways confirm that this arbecue is not positioned under a combustible object (e.g., an awning or umbrella) or in a covered area (e.g., porch or gazebo) before lighting it, to prevent a possible fire. lways confirm that this arbecue is not positioned under the overhang of a house, a garage or other structure before lighting it. n overhang will serve to deflect flare-ups and radiate heat into the structure itself, which could result in a fire. lways confirm that this arbecue is positioned more than 36 (91.4cm) away from any combustible materials or surfaces before lighting it, and that no gasoline or other volatile substances are stored in the vicinity of this arbecue. The temperature of a grease fire or of the radiated heat might otherwise be sufficient to ignite nearby combustibles or volatile substances. Do not position near windows, siding, or fencing. lways locate the arbecue where there will be ample combustion and ventilation air, but never position it in the direct path of a strong wind.

24 Join the conversation facebook.com/colemangrills twitter.com/colemangrills Manufactured by Winners Products Engineering Ltd. Coleman, and are registered trademarks of The Coleman Company, Inc. used under license The Coleman Company, Inc.