Installation Instructions
|
|
- Hope Moore
- 5 years ago
- Views:
Transcription
1 Installation Instructions D-Series Mast Adaption Kits for Internal Reeving This sheet describes the installation of Adaption Kits to provide a high termination for Lift Tek D-Series Masts. The Kits are for standard carriages with -in. ( cm) bars and contain the necessary hoses, tubing, brackets and fittings to connect between the mast internal reeving and the upper bar. See Sheet 7 for Hi-Vis Masts with -in. (0 cm) bars. The illustrations on this page show where to weld the upper hose terminal mounting brackets. The following pages show hose and fitting location, and part numbers for the contents of each kit. Reuseable fittings are provided on the hoses to enable hoses to be cut to an exact length. Clean all surfaces to be welded. Remove any paint, oil, grease or other contaminants. Position the bracket(s) on the back side (driver s view) of the mast upper carriage bar using the dimensions shown. Clamp the bracket(s) in place. NOTE: 0D-MS Masts require additional brackets on the vertical carriage bar(s). Weld the brackets to the mast carriage using the following weld procedures: Protect hoses and adjacent areas from weld splatter. Preheat weld areas to 70 F ( C). WELD METHOD A FCAW (Flux-Cored Arc Weld). Attach ground wire to carriage. Weld using AWS E70T- / in. (. mm) or / in. ( mm) diameter wire with 00% CO shielding gas at 0 CFH. Set welding amps per manufacturer s recommendations. Apply weld holding a close arc. Do not oscillate or use a wash bead pattern. Let welds normal air-cool. WELD METHOD B SMAW (Stick Welding). Attach ground wire to carriage. Weld using E-708 low hydrogen /8 in. (. mm) or / in. ( mm) diameter electrodes. Set welding amps per manufacturer s recommendations. Do not use electrodes exposed to moisture without first re-drying them at 00 F (7 C) for hours. Apply weld holding a close arc. Do not oscillate or use a wash bead pattern. Let welds normal air-cool. Remove all slag and weld splatter and inspect the welds. Part No. 88 R- WARNING: Lift Technologies recommends that a qualified welder experienced in this type of work be used for best quality. / in. ( mm) in. ( cm) Mast Upper Carriage Bar Vertical Carriage Bar Bracket (0D-MS mast only) A Front View Bracket (location similar for RH side) Back (driver s) view Mast Model 0//0/0D-MT /D-MQ 0D/D/0D-MS, MD D/0D-MT Bracket (all masts) A / in. ( mm) Dimension A -/ in. ( mm) -/ in. ( mm) -/ in. ( mm) 7-/ in. (8 mm) Terminal Brackets(s) -/ in. (7 mm) cushion tire / in. ( mm) pneumatic tire MA07.ill / in. ( mm) Horizontal Carriage Bar MA08.ill For Technical Support...or to Order Parts Call: OR Write: Lift Technologies, 700 South Highway, Westminster, S.C.
2 D-Series 0D-MS MAST NOTE: All illustrations are shown as viewed from the driver s seat. (Hidden kit components show through.) 7 8 MA0.ill 7 Double Function Single Function LH Single Function RH MA0.ill 0D-MS A to C A to D A to D and B to C REF QTY PART NO. PART NO. PART NO. DESCRIPTION Adaption Kit 7 7 Fitting, Fitting, Bracket 870 Bracket 0 0, 0, 8 8, 8, 7 7 Fitting, -8 7 Fitting, Tube, Tube 8,, Used for Quick-Change couplers. Reference: S-
3 D-Series D/0D-MS MASTS 7 MA0.ill 7 8 MA08.ill D-MS 0D-MS A to C A to D B to C A to D and A to C A to D B to C A to D and B to C B to C REF QTY PART NO. PART NO. PART NO. PART NO. PART NO. PART NO. PART NO. PART NO. DESCRIPTION Adaption Kit Fitting, Fitting, Bracket Bracket 0,,,, Fitting, Fitting, Tube Tube Tube Tube Fitting, Fitting, -8 Used for Quick-Change couplers. Reference: S-
4 D-Series /D-MQ and 0//0/0D-MT MASTS Single Function LH Single Function RH MA0.ill MA00.ill Double Function /D-MQ and 0//0/0D-MT A to D B to C A to D and A to D and B to C B to C REF QTY PART NO. PART NO. PART NO. PART NO. DESCRIPTION Adaption Kit, No. hose 7 Adaption Kit, No. and hose 7 7 Fitting, Fitting, Bracket Bracket 0, 0, ( in.) 78, ( in.) 7 7 7, 7, (8. in.) 77, (8. in.) Fitting, -8 7 Fitting, -8 Used for Quick-Change couplers. Reference: S- D-MQ only.
5 D-Series D/0D-MD and MT MASTS MA0.ill MA00.ill D-MD and MT 0D-MD and MT A to C A to D or A to D and A to C A to D or A to D and B to C B to C B to C B to C REF QTY PART NO. PART NO. PART NO. PART NO. PART NO. PART NO. DESCRIPTION Adaption Kit Fitting, Fitting, Bracket Bracket 7 8, 7, 0 07, 07, Fitting, Fitting, -8 Used for Quick-Change couplers. Reference: S-, S-
6 Reusable Fittings Kit hoses are equipped with reusable fittings to enable hoses to be modified to the exact length required for installation. IMPORTANT: Do not shorten hoses to the point where they will be stretched or kinked when installed. When routing hoses, make sure they will not be pinched, rubbed, twisted, or otherwise damaged throughout their full range of movement. Use hose clamps to secure hoses if required. Fitting Removal To shorten a hose, remove either end-fitting using the following procedures: Clamp the fitting socket in a vise. Lubricate an assembling mandrel* with hydraulic fluid. Slide the mandrel into the nipple and engage the nipple nut threads. Using two wrenches, screw the mandrel into the nipple nut. * Stratoflex PN : 70--8S (# hose), 07--S (#8 hose). Assembling Mandrel Nipple Nipple GA00.ill GA00.ill GA007.ill Nipple With a wrench on the nipple nut, unscrew the nipple from the hose socket. Reassembly Cut the hose to the desired length using a fine-toothed hacksaw or hose cutoff machine. Make sure the hose is not cut too short for proper installation. GA008.ill Clamp the socket in a vise and turn the hose into the socket counterclockwise (CCW) until it bottoms. For long hoses, clamp the hose in a vise and turn the socket CCW onto the hose. Back the hose out /- turn. Lubricate the mandrel/nipple assembly and the inside of the hose with hydraulic fluid. Insert the nipple into the hose, making sure it moves in and out freely. Mandrel/Nipple Assembly Mandrel / / in. (.8. mm) GA000.ill GA00.ill With a wrench on the mandrel, screw the nipple into the fitting socket. Leave / to /-in. (.8 to. mm) clearance between the nipple nut and socket so the nut swivels freely. Mandrel GA00.ill Using two wrenches, remove the mandrel from the nipple nut. GA00.ill IMPORTANT: Inspect the hose for proper assembly. Sight Clamp the socket in a vise and manually turn the hose down the fitting ID to assure that the nipple did not scarf a clockwise (CW) to remove it from the socket. For long piece of hose material that might prevent free flow. If hoses, clamp the hose in a vise and turn the socket damage is found, remove the fitting and cut away the CW to remove it from the hose. damaged hose. Reassemble the hose as in Steps through. Use compressed air to clear the hose of debris. Lift Technologies 00-0 Part No. 88 R-
Swagelok Thermoplastic Hose Hand Swager User s Manual
Swagelok Thermoplastic Hose Hand Swager User s Manual Thermoplastic Hose Hand Swager User s Manual Contents Hand Swager Components....................... 2 Setup Swager.......................................
More informationAerospace. Light Weight and Flexible Qualified to Industry Standards. Fluid Conveyance
Aerospace Fluid Conveyance Aeroquip Brand Rubber Hose, & Assemblies for Aerospace Applications Light and Flexible Qualified to Industry Standards 303, 302A Medium Pressure Hose,, and Assemblies Construction:
More informationThermostatic Griddle Field Service Kit Instructions
Thermostatic Griddle Field Service Kit Instructions The following document provides instructions on how to install a Garland Thermostatic Griddle Field Kit and is applicable to each 2 section of a Garland
More informationZL1 Camaro Intercooler Fluid Reservoir Kit
ZL1 Camaro Intercooler Fluid Reservoir Kit PN: L300152012 Revision - 1.2 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761 fax www.lingenfelter.com
More informationCHANGING YOUR LANDSCAPE SINCE 1945 OWNER S MANUAL. Tow Hitch Replacement Kit For Rough Cut Trailcutters. Starting Serial # L
CHANGING YOUR LANDSCAPE SINCE 1945 OWNER S MANUAL Tow Hitch Replacement Kit For Rough Cut Trailcutters 21100 Starting Serial # L118-023001 Tools Required: Wrench/Socket Qty. Size (1) 1-1/8 (1) 1-1/16 (2)
More informationBILLY GOAT KV HOSE KIT (P/N ) PURPOSE: To allow for vacuuming in hard to reach places.
BILLY GOAT KV HOSE KIT (P/N 891125) PURPOSE: To allow for vacuuming in hard to reach places. Part No 891061-1 - Form No F052209A INSTALLATION: Step 1. Attach nozzle wear guards. 1. Disconnect spark plug
More informationBlue Series Hot Melt Hose with RediFlext II Hanger System
Instruction Sheet P/N 1124594_01 Blue Series Hot Melt Hose with RediFlext II Hanger System Safety WARNING! Allow only personnel with appropriate training and experience to operate or service the equipment.
More informationAdvantage Plus TIM-3600 Series Reel
Read the following precautions and instructions before you begin assembly or using. Failure to comply with these instructions could result in personal injury or property damage. Keep these instructions
More informationCleaning Fireside Franklin Pilot Orifice
Cleaning Fireside Franklin Pilot Orifice Please read all the instructions before beginning the procedure. Confirm that you have all the necessary tools and materials. If you have any questions technical
More informationMazdaspeed6 Stage 1 Location 2 OCC Kit Install guide
1 Mazdaspeed6 Stage 1 Location 2 OCC Kit Install guide WARNING: By installing this Product, you understand that: The buyer/user assumes all risk as to quality, performance and use of these products and
More informationAssembly TOOLS REQUIRED: 17mm and 14mm or equivalent wrenches.
Instructions for 3 Trimmer Rack, 3TR* *Patents Pending Assembly TOOLS REQUIRED: 17mm and mm or equivalent wrenches. 15 26 26 16 15 16 Attach the lower mounting brackets to the Trimmer Rack poles as shown
More informationSynflex Assembly Equipment and Accessories
Synflex Assembly Equipment and Accessories H1 Synflex Swaging Machines SST and Mark IX Designed to Attach Synflex Permanent Fittings to Synflex Hose Synflex swaging equipment produces smooth, uniform fitting
More information300 ft. 5/8 Hose wagon
300 ft. 5/8 Hose wagon Model 95956 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. (Garden hose is not included).
More informationWIDESPREAD LAVATORY MODELS WITH HI-ARC SPOUT
5951, 5961, 5981, 5983, 5993 SERIES MT122B INSTALLATION INSTRUCTIONS THESE INSTRUCTIONS MUST BE LEFT WITH HOMEOWNER WIDESPREAD LAVATORY MODELS WITH HI-ARC TRADITIONAL CROSS NOTE: Handle Inserts are not
More informationREPLACEMENT PROCEDURE: ROTISSERIE ORIFICE: TOOLS REQUIRED TO INSTALL THIS KIT: ITEM DESCRIPTION: E C
TOOLS REQUIRED TO INSTALL THIS KIT: ITEM DESCRIPTION: A SCREWDRIVER - PHILIPS SIZE # 2 B SCREWDRIVER - FLAT 1/8 WIDE TIP C 1/2 WRENCH - OPEN TYPE D 7/16 WRENCH - OPEN TYPE E RATCHETING SOCKET WRENCH -
More informationDC 700 Series Hose Reel - September 2010
Instructions Parts List Service Manual DC 700 Series Hose Reel - September 2010 Suitable for dispensing, transfer and evacuation of lubricants, fuels, air & other automotive & industrial products. To be
More informationAircraft may be inanimate
nuts & bolts craft & technique Practical Plumbing Fabricating aircraft hoses in 10 easy steps Ronald Sterkenburg Aircraft may be inanimate creations of wood, steel, cloth, aluminum, and composite materials,
More informationINSTRUCTION SHEET DETHATCHER KIT. STS-422LX LPSTS-42JD Assembly Installation Operation Repair Parts L-1660-D. Visit us on the web!
INSTRUCTION SHEET DETHATCHER KIT MODEL: DK-422LX FOR USE WITH SWEEPER MODEL: STS-422LX LPSTS-42JD Assembly Installation Operation Repair Parts For use with Riders and Lawn/Garden Tractors For the latest
More information300 Model 870 Four Wheel Hose Cart Owner s Manual
300 Model 870 Four Wheel Hose Cart Owner s Manual IMPORTANT: READ THE OWNER S MANUAL BEFORE ASSEMBLING TOOLS REQUIRED: TWO ADJUSTABLE WRENCHES; HAND PUMP Estimated assembly time: 30 minutes PARTS LIST
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationINSTALLATION GUIDELINES
IMPORTANT: To ensure this product is installed properly, you must read and follow these guidelines. The owner/user of this product must keep this information for future reference. This product must be
More information42" SNOW BLADE. Owner's Manual. Model No Safety Assembly Operation Maintenance Parts
Owner's Manual 42" SNOW BLADE Model No. 486.24443 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Safety Assembly Operation Maintenance Parts
More informationInstallation, Operation and Maintenance Manual
Document Number 47420 One Inch for 48 in. long Jackshafts Note: Kit includes required parts for single section dampers. Attach jackshaft brackets (Item 2) to the frame with 4-20 thread studs (Item 3) and
More informationquick and easy installation guide
www.directdriveopener.com quick and easy installation guide Back 2 Front. Motor Carriage 2. C-rail. Chain. Limit stops. Slide in part (tensioner) Rail assembly Insert C-rail parts () into the connecting
More informationEaton ET Hydraulic Hose Saw INSTRUCTION MANUAL
Eaton ET9100-07-110 Hydraulic Saw INSTRUCTION MANUAL INSTRUCTION MANUAL Eaton ET9100-07-110 Hydraulic Saw Table of Contents Introduction... 3 Old Method... 3 New Eaton Method... 3 Operation... 4 Operation
More informationOWNER S TECHNICAL MANUAL
OWNER S TECHNICAL MANUAL Heavy Duty Oil Hose Reel 504200 Description Open hose reel for air, water (high or low pressure), oil or grease, depending on model. Uncoil the hose to the desired length. It can
More informationUser s Manual Trampoline 8
User s Manual Trampoline 8 Model! WARNING Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Maximum user weight 17 lbs. ASSEMBLY IMPORTANT
More informationThomas Scientific Swedesboro, NJ U.S.A.
Thomas Scientific Swedesboro, NJ 08085-0099 U.S.A. Wiley Laboratory Mill, Model 4 3375-E10 (115 V, 50/60 HZ) USE AND CARE OF CATALOG NUMBER: 3375-E10 Wiley Laboratory Mill, Model 4 (115 V, 50/60 HZ) UNPACKING
More informationPRODUCT MANUAL - M096
PRODUCT MANUAL - M096 MODEL 270 ELECTRIC CAN OPENER 1 I. LABELS L087--CAUTION 2 II. SPECIFICATIONS MODEL NO. 270 POWER 115 VOLT, 1.5 AMP, 50-60HZ REQUIREMENTS 230 VOLT, 0.8 AMP, 50-60 HZ NORMAL SPEED 200-250
More informationInstallation & Operation Manual VHM Variable Height Series Arms with Fixed Angle Front End
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation & Operation Manual VHM Variable Height Series Arms with Fixed Angle Front End Products covered
More informationFORM (Apr. 2006)
2212 Slcier MODEL 2212 SLICER MODEL 2212 ML-136132 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 35215 (Apr. 2006) Installation, Operation, and Care of MODEL 2212 Slicer
More informationMazdaspeed Version 1 Oil Catch Can Kit Install Guide
Mazdaspeed 3 2010+ Version 1 Oil Catch Can Kit Install Guide 1 WARNING: By installing this Product, you understand that: The buyer/user assumes all risk as to quality, performance and use of these products
More informationModel 698/ and Model in 1 Hose Reel Owner s Manual
Model 698/694 200 and Model 706 100 4 in 1 Hose Reel Owner s Manual 698/694 706 VISIT OUR WEBSITE: WWW.LIBERTYGARDENPRODUCTS.COM OR CALL US TOLL FREE AT 1-866-820-5805 LIBERTY GARDEN PRODUCTS, INC. 500
More informationTC36 CHALET BURNER KIT INSTALLATION INSTRUCTIONS
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationZICO 3090PM4. Horizontal Hard Suction Mount Kits HHS-TM-1, HHS-TM-2, HHS-TM-1-ST, HHS-TM-2-ST, HHS-TMV-2, HHS-TMV-2-ST Parts and Instruction Manual
Horizontal Hard Suction Mount Kits Models HHS-TM-1, HHS-TM-2, HHS-TM-1-ST, HHS-TM-2-ST, HHS-TMV-2, HHS-TMV-2-ST Parts and Instruction Manual ZICO 3090PM4 Rev. 9-27-18 I. SYSTEMS AVAILABLE A. HHS-TM-1:
More informationADDED PROTECTION FOR SLIDE-OUT ROOMS. Installation. Introduction... 2 Product Overview...2 Component Checklist...3
CAREFREE SIDEOUT KOVER II RV Installation ADDED PROTECTION FOR SLIDE-OUT ROOMS TABLE OF CONTENTS SOKII Shown with Full Case Option Introduction... 2 Product Overview...2 Component Checklist...3 Installation...
More information1612P MODEL 1612P SLICER MODEL EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO FORM (4-95)
1612P MODEL 1612P SLICER MODEL 1612P ML-104587 EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO 45374-0001 FORM 19370 (4-95) Installation, Operation, and Care of MODEL 1612P SLICER SAVE THESE INSTRUCTIONS
More information6275-S1 PNEUMATIC DRILL OPERATING MANUAL ORIGINAL INSTRUCTIONS. P/N November 2014 Revision 1
6275-S1 PNEUMATIC DRILL OPERATING MANUAL ORIGINAL INSTRUCTIONS P/N 80749 November 2014 Revision 1 2014 Climax Portable Machining and Welding Systems or its subsidiaries. All rights reserved. Except as
More informationKey Largo Fire Pit. Installation Instructions. 1 P a g e. NorthlineExpress.com. Toll-Free
Key Largo Fire Pit Installation Instructions 1 P a g e Contents Contents..2 Required Tools..3 Placing and assembling the Table. 4 Gas Connection..5 Igniter Installation....6 Locating Propane tank 8 Finishing
More informationNapa Valley Fire Pit Table
Napa Valley Fire Pit Table 48 x48 Model Installation Instructions For Models: NAPA-VALLEY-2424-K, NV-2424-BRN-K, NV-2424-BLK-K, NV-2424-GRY-K, NV-2424-BLK-W-K 1 P a g e Contents Contents..2 Required Tools..3
More informationEaton ET Hydraulic Hose Saw INSTRUCTION MANUAL
Eaton ET9200-10-220 Hydraulic Hose Saw INSTRUCTION MANUAL INSTRUCTION MANUAL Eaton ET9200-10-220 Hydraulic Hose Saw Table of Contents Introduction... 3 Old Method... 3 New Eaton Method... 3 Operation...
More informationInstallation Guide. Single-Control Kitchen Sink Faucets
Installation Guide Single-Control Kitchen Sink Faucets K-6352 K-6353 M product numbers are for Mexico (i.e. K-12345M) Los números de productos seguidos de M corresponden a México (Ej. K-12345M) Français,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Pictures in this manual are shown with the optional visual display indicator installed on the filter. BLUE FLAME & BLUE FLAME II MAXX LP FILTER KIT (423-375-001A) SHIVVERS SHIVVERS
More informationTWISTLOCK VEHICLE STABILIZER (TVS) SYSTEM INSTRUCTIONS
TWISTLOCK VEHICLE STABILIZER (TVS) SYSTEM 22-797010, 22-797020, 22-796161 INSTRUCTIONS COMPONENTS: 1. TVS-100, PN 22-797010: 47 60 (119 cm 152 cm) stroke TwistLock Vehicle Stabilizer. Component weight,
More informationREAD ME! IMPORTANT WARNING! ENG. Quick Release Tent Mount Kit
Quick Release Tent Mount Kit ENG TBMK008 READ ME! Thank you for purchasing a Front Runner Quick Release Tent Mount Kit. Before you start, take a moment to familiarize yourself with the Fitting Instructions
More informationASSEMBLY GUIDE. Customer Service: INCH² 2-BURNER & 864 INCH² 2-BURNER
ASSEMBLY GUIDE 688 INCH² 2-BURNER & 864 INCH² 2-BURNER DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open lid. 4. If odor continues, keep away from the appliance
More informationWater Trailer Series. WT5HR Hose Reel Kit Installation REQUIRED TOOLS PARTS WORK SAFELY! PREPARATION
Water Trailer Series WT5HR Hose Reel Kit Installation The following instructions are intended to assist the user in the installation of the WT5HR Hose Reel Kit for use on the WT5C, WTE5C, WT5CSG Series
More informationINSTRUCTIONS INSTALLATION UNIVERSAL SERIES PATIO AWNING HARDWARE , , ,
RECORD THIS INFORMATION FOR FUTURE REFERENCE: Model Number Serial Number Hardware Model Number Hardware Serial Number Date Purchased Retailer / Qualified Installer INSTALLATION INSTRUCTIONS UNIVERSAL SERIES
More informationNS 200 Series Hose Reel January 2011
Instructions Parts List Service Manual NS 200 Series Hose Reel January 2011 Suitable for dispensing, transfer and evacuation of lubricants, fuels, air & other automotive & industrial products. To be used
More informationProduct instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E
Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E The Trimfast Ream Cutters are reliable, high performance cutters that will give you the results you need quickly
More informationPrimrose Awnings - Full Cassette Manual & Electric Instructions
Primrose Awnings - Full Cassette Manual & Electric Instructions Contents Warning 2.0m - 3.5m Awnings 8 x Expansion bolts ** 2 x brackets 1 x Awning 1 x Winder 4.0m - 5.0m Awnings 12 x Expansion bolts **
More informationGas Conversion Kits and Instructions
Gas Conversion Kits and Instructions INSTALLATION FORM RGM 432/433-GC (Version D.1) Obsoletes Form RGM 432/433-GC (Version D) APPLIES TO: Model FT and Model SFT All gas conversion must be done by a qualified
More informationShut off combine and remove key before installing the hopper extension. Make sure the combine is on a level surface. Engage parking brake.
ASSEMBLY INSTRUCTIONS CASE IH 5088, 6088/7088, 7010/8010 & 7120/8120/9120 Series NEW HOLLAND CR STD Series Combines (Large) big top 26301(service only), 29976 (service only), 53408, 53543 & 54274 The Crary
More informationSERVICE MANUAL- M126
SERVICE MANUAL- MANUAL CAN OPENER- MODEL # 2 1 Model #2 Can Opener Assembly Procedure The Model #2 can opener will be assembled according to the following procedure. I. Model #2 Handle and Arbor Assembly
More informationHL GUIDE-ON INSTRUCTIONS
HL GUIDE-ON INSTRUCTIONS OBSOLETE REIMANN & GEORGER CORPORATION MARINE PRODUCTS BUFFALO, NY P/N 6114110 6/19/01 SPECIFICATIONS P/N DESCRIPTION ADJUSTMENT WOOD SIZE (inches) RANGE (inches) L x W x H 4110045
More informationAPPENDIX A LIGHT SOURCE
APPENDIX A LIGHT SOURCE GASOLINE LANTERN One source of artificial light for the field kitchen is the gasoline lantern (NSN 6260-00-170-0430). It is a one-mantle lantern with a heat-resistant globe or globe
More information* * KR54-F, KR9854 & KR9954 Installation Instructions. Read All Warnings Before Starting Installation! Index:
*941061-00* 941061-00 Keyed Removable Mullion KR54-F, KR9854 & KR9954 Installation Instructions CLASSIFIED CLASSIFIED C Read All Warnings Before Starting Installation! Index: General Information ----------------
More informationflatbed kit InstalLation Instructions kit contents KIT (tacoma ) kit (hilux )
InstalLation Instructions flatbed kit 300721-KIT (tacoma 1995-2004) 301047-kit (hilux 1984-1995) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950 WWW.TRAIL-GEAR.COM
More informationINFRARED BURNER KIT INSTRUCTIONS
6 4 3 2 INFRARED BURNER KIT INSTRUCTIONS 1 Model # 3049 (A790, A660, & A530) Model # 3051 (A540, & A430) Included parts 5 NOTE: This unit has been retrofi tted with an infrared burner. PARTS INCLUDED 1.
More informationSHOWER CONVERSION KIT WITH HAND SHOWER
SHOWER CONVERSION KIT WITH HAND SHOWER BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage
More informationAntenna Tower Positioning System
Model 1052 Antenna Tower Positioning System User Manual (Antenna not included) ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve function, design,
More informationUptown Fire Pit Table
Uptown Fire Pit Table Installation Instructions 1 P a g e Contents Contents..2 Required Tools..3 Placing and assembling the Table. 4 Gas Connection..5 Igniter Installation....6 Locating Propane tank 8
More informationRAFTER VI. Installation and Operation CAREFREE WITH AUTOMATIC AWNING SUPPORT. RV Accessory PRODUCT OVERVIEW
CAREFREE RAFTER VI RV Accessory WITH AUTOMATIC AWNING SUPPORT Installation and Operation PRODUCT OVERVIEW The gives the awning user the ability to easily tighten the center fabric when the awning is extended.
More informationASSEMBLY & CARE INSTRUCTIONS
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 3 9 Part No. FT3711 - on road FT3923 - off road OPTIONAL SUNROOM Wall and floor kit Part No. FT3723 - on road FT39 - off road OPTIONAL SPARE ROOM Roof,
More informationSynflex. Mini Catalog
Synflex Mini Catalog Table of Contents Hose Selection Chart Core 5 Hoses (Application/Product) 2 3R30, 3130, 3580, 30CT, 3R80 Core 5 Hoses (Product) 2 3R30, 3130, 3580, 30CT, 3R80 Hose 3R30 Low Pressure
More information4A1-114/114KR & 4A1-2 MANUAL TENSIONERS
M L. C O O N AL TO 4A1-114/114KR & 4A1-2 W W W.T R AD IT IO MANUAL TENSIONERS READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SEVERE PERSONAL INJURY. GENERAL SAFETY
More informationGoBidet Bidet Attachment
GoBidet Bidet Attachment 151 Ruths Place #5 Sequim, WA 98382 Tel 1-800-681-0753 Fax +1 360-681-4029 www.go-bidet.com MODEL #2003C In this box: 1 User Manual 1 GoBidet Unit w/ mounting bracket, nut, rubber
More information* * 4023 KR. Step 1 Prepare the Keyed Removable Unit. Not for use on electric or fire rated removable mullions
condition. *64009-00* 64009-00 Keyed Removable Mullions 403 KR Installation Instructions Not for use on electric or fire rated removable mullions This kit includes the following parts: (Not to scale) 5/6
More informationCore Systems Installation Instructions
185-3017 185-3018 185-3517 607-0149 WLH 09/17/18 TABLE OF CONTENTS ***Assembly*** Roller Tube Assembly Roller Tube Assembly... Standard Application Attaching Tarp to Roller Tube - Standard... Installing
More informationASSEMBLY & CARE INSTRUCTIONS. 7 x4 TRAILER TENT SERIES 4 9. OPTIONAL SUNROOM Wall and floor kit. OPTIONAL SPARE ROOM Roof, wall and floor kit
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 9 Part No. TM709 OPTIONAL SUNROOM Wall and floor kit Part No. TM723 OPTIONAL SPARE ROOM Roof, wall and floor kit Part No. TM76 Please keep these instructions
More informationUrea/Adblue Hose Reel
www.scintex.com.au sales@scintex.com.au Model: SHR3408 Urea/Adblue Hose Reel Product Manual Specifications Spring driven drum: for automatic rewind. Locking ratchet: to maintain the desired length of hose
More informationFREEDOM WM AWNING. Product Overview... 1 Component Checklist... 2
INSTALLATION MANUAL FREEDOM WM AWNING MOTORIZED OR MANUAL LATERAL ARM BOX AWNING RV Read this manual before installing or using this product. Failure to follow the instructions and safety precautions in
More informationPrimrose Awnings Half Cassette Manual & Electric Instructions
Primrose Awnings Half Cassette Manual & Electric Instructions Contents for 2.5m, 3m Awnings 4 x Expansion bolts (2 per bracket)** 2 x brackets 1 x Awning Contents for 3.5m, 4m Awnings 6 x Expansion bolts
More informationTUBULAR BURNER CONVERSION KIT AGCK-TBXX / AECK-UBXX
TUBULAR BURNER CONVERSION KIT AGCK-TBXX / AECK-UBXX IMPORTANT - READ ALL INSTRUCTIONS BEFORE YOU BEGIN THE INSTRUCTIONS HEREIN SHOULD BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. THE GRILL MUST BE COMPLETELY
More informationINSTRUCTION SHEET TWISTLOCK VEHICLE STABILIZER (TVS) SYSTEM PN S: , ,
INSTRUCTION SHEET TWISTLOCK VEHICLE STABILIZER (TVS) SYSTEM PN S: 22-797010, 22-797020, 22-796161 COMPONENTS: 1. TVS-100, PN 22-797010: 47 60 (119 cm 152 cm) stroke TwistLock Vehicle Stabilizer. Component
More informationPrimrose Awnings Full Cassette Manual & Electric Instructions
Primrose Awnings Full Cassette Manual & Electric Instructions Contents for Full Cassette Awning 1 x Remote control receiver box 2 x Remote hand-held zappers 1 x 5 metre cable 1 x Template sticker **The
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS KR54, KR1654, & KR4954 Keyed Removable Mullion NOT FOR USE ON ELECTRIC OR FIRE RATED MULLIONS. This kit includes the following parts: (Not to scale) WARNING Remove key, reinstall,
More informationInstallation Guide. LPKPDR - Universal LP Conversion Kit for Professional & Designer Ranges/Rangetops. Viking Range, LLC.
Installation Guide Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-845-4641 LPKPDR - Universal LP Conversion Kit for Professional
More informationFLEX KEY ASSEMBLY. ..._ o RAFTER ARM TUBE MAIN ARM TUBE CAP NUT CLAW HINGE
ZIP DEE Inc. 96 Crossen Ave. Elk Grove Village, IL 60007(847)437-0980 (800)338-2378 HEAD CASTING AWNING RAIL FLEX KEY ASSEMBLY..._ o GM1 Installation Instruction GMC Motorhome RAFTER ARM TUBE MAIN ARM
More informationContents. Introduction...3 Description...3. Pack Contents...4. Rada Heavy Duty EV Shower Fittings Right Angled Connector (RAC)...
SHOWER FITTINGS PRODUCT MANUAL IMPORTANT Installer: This manual is the property of the customer and must be retained with the product for maintenance and operational purposes. Contents Introduction...3
More informationINSTRUCTION MANUAL HYDM140
INSTRUCTION MANUAL HYDM140 INSTRUCTION MANUAL Clean-Cuts HYDM140 Hydraulic Hose Saw Table of Contents Introduction... 3 Old Method... 3 New Clean-Cuts Method... 3 Operation... 4 Operation Procedure...
More informationUnshielded Fluid Hose Kit
Instructions Unshielded Fluid Hose Kit 308688C Kit Part No. 238995 Kit for converting the PRO 5500wb Spray Gun and the PRO Auto Xs wb Spray Gun to allow the use of a bare PTFE(unshielded) fluid hose. Order
More informationEEZI - AWN series 1000 / 2000 Awning bracket
EEZI - AWN series 1000 / 2000 Awning bracket RRAC063 INSTALL TIME: 15 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
More informationKey Largo Fire Pit. Installation Instructions for Key Largo, all base materials and top styles. 1 P a g e
Key Largo Fire Pit Installation Instructions for Key Largo, all base materials and top styles 1 P a g e Contents Contents 2 Required Tools...3 Placing and assembling the Table. 4 Gas Connection..5 Igniter
More informationOperating Instructions
Operating Instructions Medium and High Pressure Model Numbers: RT602- RT635- RT602- RT635- RT603- RT650- RT603- RT650- RT605- RT825- RT605- RT650-SM RT802- RT835- RT425- RT803- RT402- RT435- RT625- RT403-
More informationPARTS LIST CHARGER 2022 ABLT
PARTS LIST CHARGER 2022 ABLT HEAD ASSEMBLY ITEM PART NO. DESCRIPTION QTY 101 5990731 SPRING CLIP PAD HOLDER SET INCLUDES: 1 101A 9120205 #8 X 1/2 PAN HEAD PHILLIPS SHEET METAL SCREW PACK OF 3 3 102 9121490
More informationSERVICE PARTS LIST AND ASSEMBLY INSTRUCTIONS
R Transport Air Conditioning FlexCLIK 58-64105-03 #12 [16MM], 35 Bar, SAE J2064 Type E FlexCLIK 58-64105-02 #10 [13MM], 35 Bar, SAE J2064 Type E FlexCLIK 58-64105-01 #8 [10MM], 35 Bar, SAE J2064 Type E
More informationCOOPER FREESTANDING TUB FAUCET INSTALLATION
SKU(s): 940972 COOPER FREESTANDING TUB FAUCET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no
More informationApplication Tooling Specification
Order No. 200218-3100 FEATURES Application Tooling Specification A full cycle ratcheting hand tool ensures complete crimps Long handles for comfortable crimping with reduced crimping force and a safety
More informationCabinet Mount Assist Lift n Lock Instructions
Cabinet Mount Assist Lift n Lock Instructions PART LIST 2 @ Gas Cylinder 1 @ Lock Bar 2 @ Rubber Sleeve (preset) 4 @ Stopper Pin (2pcs preset) 4 @ Saddle Block 8 @ 19mm Black PVC Cap 5 @ 14mm Black PVC
More informationAn Improved Pedestal To A Version One Worksurface
Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 An Improved Pedestal To A Version One Worksurface NOTE: This installation applies to 25, 30, and 35 deep worksurfaces with lock rail only. VERSION
More informationTall Cabinet Drawer Keyless Double Lock Installation [ xx]
Tall Cabinet Drawer Keyless Double Lock Installation [002-97-xx] Note This install can be used for any Tall Cabinet Double Drawer Keyless Lock installation. The assembly process will be the same. The will
More informationREAD ME FIRST! IMPORTANT WARNING! ENG. Roof top tent
Roof top tent ENG TENT031 220 min READ ME FIRST! Thank you for purchasing a Front Runner Roof Top Tent. Before you start, take a moment to familiarize yourself with these Fitting Instructions and the components
More informationOWNER S MANUAL: G5000 SLIDE-OUT AWNING SYSTEM
INSTALLATION, OPERATIONS, ADJUSTMENT AND REPAIR Rev. 08/01/12 1361 Calle Avanzado San Clemente California 92673 Office: (949) 259-4000 Toll Free: (800) 382-8442 Fax: (949) 276-5500 TABLE OF CONTENTS WARRANTY
More informationInstallation Instructions for the Rolltec Adalia X3M Extenda Awning
Installation Instructions for the Rolltec Adalia X3M Extenda Awning Questions? Call Rolltec at 1-800-667-0474 General Tool Requirements Table of Contents Available installation brackets Side dimensions
More informationSection B 5 Parts. 1. Introduction. Using the Illustrated Parts List. Parts B 5-1
Parts B - Section B Parts. Introduction To order parts, call the Nordson Customer Service Center or your local Nordson representative. Use the parts list, and the accompanying illustration, to describe
More informationModel 205 Fireview Maintenance Kit
Model 205 Fireview Maintenance Kit Please read all of the instructions before you begin the procedure. Confirm that you have all the necessary tools and parts required. Allow about one hour to complete
More informationWorm Gear Clamps. Spiral Double-Bolt Clamps. The Ultimate in Clamping for Your Vacuum Hose. With Plated Carbon Steel Deep-Slotted Screw
Worm Gear Clamps 5/16" Hex Stainless Steel Band Can Be Used on Any Hose Available with Stainless Steel or Plated Carbon Screws With Stainless Steel Screw FITS HOSE O.D. FROM TO SSHC-6* 7/16" 25/32" SSHC-8
More informationPrimrose Awnings - Standard Manual Instructions
Primrose Awnings - Standard Manual Instructions Contents Warning 1.5m - 3.0m Awnings 4 x Expansion bolts (2 per bracket)** 2 x brackets 1 x Awning 1 x Winder handle 3.5m - 4m Awnings 6 x Expansion bolts
More informationDO NOT USE WITH CROSSBAR SPREAD LESS THAN 24.
TM Please read all instructions carefully before assembly, installation and/or use of this product. DO NOT USE WITH CROSSBAR SPREAD LESS THAN 24. WARNING: Do not exceed the weight limit of your vehicle
More information