Step by Step Set Up Guide
|
|
- Juniper Ball
- 5 years ago
- Views:
Transcription
1 lite Step by Step Set Up Guide 1 lifting lug Secure lifting lugs to a certified lifting sling. Stand and stabilize escape system under work platform. Position module with round lunette ring facing work platform. Measure escape height from snubbing floor base to ground to ensure unit is within its allowable working height range for the Foxxhole Lite System being used. 4 static spine line x retension straps suspension strap Remove chute transport X retension straps (2) and store in accessories bag. Loosen but do not remove upper chute suspension tie down strap. Unravel the following: 1. Static Spine line (Blue rope found at top of chutes exit above hammock cradle) 2. Tugger line (found on underside of chutes exit). Ensure lines are not fouled. 2 Ensure module is stabilized by personnel in all operations. Remove one clevis from one lifting lug to allow for removal of top, front and back protective covers. Store all removed covers in a safe place. Replace and secure lifting sling clevis on to lifting lug. 5 lunette pintle hook Conduct interim safety meeting to address safety concerns, job functions, fall arrest and overhead lifting safety. No personnel shall be positioned directly under work area while lifting. Lift module with rig tugger line or picker assembly. Ensure lines are not fouled or attach them to other equipment during lifting. Position Lunette ring into open pintle hook at base of docking platform. Close and secure with locking pin. 3 swivel lug From accessories bag remove 2 anchoring turnbuckles. Install the open jaw of turnbuckle on to swivel lugs on the launch frame entrance. Attach turnbuckles with grade 8 bolts, lock washers and nuts supplied and securely wrench tighten. 6 Slant module frame away from docking platform to a 35º-45º degree angle from the entrance. Drop down the transition floor to cover pintle assembly. Ensure proper fit and secure in position.
2 7 rig anchor post With module positioned and install the free ends of the two turnbuckles fitted with pipe clamps to rig anchor posts. Tighten locking bolt on swivel lugs located on module frame assembly m 9.5 m 6.0 m 3 stage hammock 2 stage hammock Measurement from base of platform OPTIONAL INSTALLATION locking bolt Height measurement M-8+ design only: Auxilary static line extension for secondary and triple stage hammock deployment meter air space Required lease equipment stand off from chute 9 safety chain Snubbing Floor m 5.0m Ground Anchor Area Chute deployment working angles TOP VIEW Adjust turnbuckles to suit intended direction of drive on anchor. Turnbuckles may be lengthened or shortened to allow for up to 15 degrees left or right of centre line form exit. Install mid rail safety chains on module frame. From accessories bag Loop safety chains through D ring on each outer front side of module. Secure to work platform safety railings or other engineered structure. Adjust for tension by reducing or increasing links and secure chain loop with quick link. Determine if Static Spine line extension is required due to height of working platform. (Platform above 8.0 m to 9.5 m requires 1 extension on M-8 +, see section Static Spine line extension below.) Static Spine line connection: Fully extend turnbuckle on drive on anchor. Attach blue static spine line using carabineer to red weldless on turnbuckle. Walk anchor directly away until maximum tension can be place to Static Spine line by hand. Ensure suitable firm anchoring conditions exist on desired anchor placement on ground. Lower drive on anchor to ground while maintaining tension to Static Spine line. Static Spine line extension instalation: Remove carabineer from end of blue static spine line and attach stage extension rope from accessories bag to self locking safety hook permanently attached to original end of static spine line. Re-attach carabineer to new end of extension to Static Spine. Return to Static Spine line connection above. 11 drive on anchor Minimum 80% of vertical distance With caution stabilize drive on anchor, while front end of adequate anchoring vehicle of 3/4 ton diesel pickup or larger. Carefully directed driver to position tire in recess in middle of drive on anchor. Place vehicle in park or engage in low gear for a standard transmission. Engage park brake and remove keys to lock out location.
3 12 15 Angle of descent of Static Spine line from 35 to 60 degrees Tighten turnbuckle to desired Static Spine line tension (blue rope) approximately 200 lbs tension. (Firm resistance when pulled by hand.) Static Spine line should now be installed with a degree angle of decent dependant on height. hammock support celvis static spine line tensioning chain Unravel required cradle hammock (Stage1: m, Stage 2: 8:1-9.5 m, (Stage 3:optional system m)). ENSURE THE FOLLOWING: 1. Run yellow web loops (6) at end of the hammock cradle over clevis U body assembly to secure closure of hammock cradle. 2. Ensure Static Spine line (blue rope) has been run through the cente of hammock cradle support clevis to suspend hammock on Static Spine line. 3. Ensure Tensioning chain is installed on clevis bolt thru chain connecting link on end of chain and secure. 13 rope brake deployment/retraction line tugger line Unravel Deployment/retraction rope from top side of module. (Rope runs through rope brake). Attach end of rope to lifting unit (Rig tugger winch or picker unit) with locking hook assembly. Pull directly upwards until line is fully extended. (Do not put tension in rope). Remove chute suspension tie down strap, store in accessories bag. Ease off rope brake. Allow lifting line to be lowered to deploy chute body down spine line till chute is hanging full extended. Relieve all tension in deployment line. Note: Auxiliary chute tugger line attached to lower section of chute exit may be required to be pulled from ground level to free up chute if binding. 16 tensioning 17 chain red weldless ring Install carabineer thru desired link of chute tensioning chain and attach carabineer to Red weldless ring. Heaviest worker to lay in hammock cradle to ensure a minimum of inches of clearance from feet of worker within cradle hammock to ground below. Should adjustment be required for taking up slack, re run carabineer to shorten chain to chute hammock. Note: Chute system is designed specifically to be suspended on Blue Static Spine line on spiral ring assembly. Tension placed on clearance hammock cradle and chute body by winch or mechanical means is by no means recommended. Do not remove, alter or substitute required escape system components or operations. Ensure Static Spine line has sufficient tension to allow for proper chute and evacuee suspension. Failure to do this may interfere with the safe operation of the escape chute. Visible metal support rings at end of chute body should be at a 90 degree angle to Static Spine line for a visual check for proper suspension of applied chute tension. 18 Carry out re-inspection to confirm all components are secured and ready to be placed in service. After confirmation, place unit in service and carry out daily inspections as per recommendations in Foxxhole Lite Operations Manual.
4 lite Chute Entry & Sliding Position Office Fax hour cell Step to front of chute entrance and firmly grab hand grasp at 10 and 2 o clock position. 2. Place one leg at a time step into chute, and lower your body to stretch out fully to assume initial sliding position. 3. While you release from the hand grasp to start your descent down the chute it is very important to simultaneously make your lower body ridged and lift your heels approximately 6 inches off the chutes surface by lifting your now straight legs as you point the tip of your toes backwards toward your head. (Do not bend your legs or let your feet come in contact with the chutes surface.) 4. Place your arms above your shoulders and place your hands against the back of your head with your elbows up for the entire decent. Ensure Foxxhole Lite module is handled by qualified personnel in all operations. Treat this escape unit as a PPE device. Ensure proper PPE and fall arrest equipment are being used in all set up operations that require it. Be proactive in your own personal safety, failure to do so may result in your own injury or loss of your life. USE OF WORK BOOTS WITH AGGRESSIVE THREAD SOLES IS NOT RECOMMENDED. Should any instructions be unclear, please refer to Foxxhole Operations Manual or contact Foxxhole Escape Systems Inc. prior to use of escape system. The operator and user must have complete understanding of set up and operation of the safety device prior to use.
5 Foxxhole Lite Accessories List 15 1 Accessories Bag 2 Hammock Tensioning Chain 3 Carabineer for Tension Chain 4 Hammock support clevis 5 Red Weldless Anchoring Ring 6 Anchor Tension Turnbuckle 7 Drive on Anchor 8 Launch Frame Anchoring Turnbuckles (2) 9 Spare Bolts for Turnbuckles (2) 10 Tugger Line 11 Static Spine line c/w carabineer and safety hook 12 Static Spine line extensions (2 or 3 stage) 13 Mid Safety Railing Chains and locking links (2) X retention tie down straps (2) 15 Chute suspension tie down strap (1)
Alien Flier Zip Line Products Installation/Owner s Manual
Alien Flier Zip Line Products Installation/Owner s Manual 1 Table of Contents SAFETY PLEASE READ CAREFULLY... 4 Constructing your Zip Line Xtreme Models... 6 Installing your Alien Flier Trolley on an Existing
More informationAlien Flier Zip Line Products Installation/Owner s Manual
Alien Flier Zip Line Products Installation/Owner s Manual 1 Table of Contents SAFETY PLEASE READ CAREFULLY... 4 Explorer Zip Line EZ Up Cable Kit Installation... 5 Xtreme Zip Line EZ Up Cable Kit Installation...
More informationUser s Manual Trampoline 8
User s Manual Trampoline 8 Model! WARNING Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Maximum user weight 17 lbs. ASSEMBLY IMPORTANT
More informationAntenna Tower Positioning System
Model 1052 Antenna Tower Positioning System User Manual (Antenna not included) ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve function, design,
More informationAND LOAD CANOPY RACK SPECIFICATIONS
8MAY15 INSTRUCTIONS for the LOCK AND LOAD CANOPY RACK SPECIFICATIONS and SAFE LOADING REQUIREMENTS The Lock and Load ladder carrier for Truck Caps is a rack designed to mount to the top of a pickup truck
More informationOPERATOR INSTRUCTION MANUAL INCLUDING REPAIR PARTS FOR MODULAR GENERAL PURPOSE TENT SYSTEM (MGPTS) TYPE I
OPERATOR INSTRUCTION MANUAL INCLUDING REPAIR PARTS FOR MODULAR GENERAL PURPOSE TENT SYSTEM (MGPTS) TYPE I Johnson Outdoors Gear, Inc. Eureka! branded tent products 625 Conklin Road Binghamton, NY 13903
More informationDO NOT use Alien Flier Zip Line Products until you have read and fully understand the SAFETY WARNINGS below!
SAFETY WARNING DO NOT use Alien Flier Zip Line Products until you have read and fully understand the SAFETY WARNINGS below! Assumption of Risk Zip line construction and use can be dangerous. Ensure you
More informationInstallation Guide Cable
Installation Guide Cable Thank you for selecting a DuctSox System. This guide will be helpful for the installation of a Cable System. Sections of fabric will be labeled, assembled, bagged, and boxed for
More informationDOWN MANUAL. Aeros Ltd. St. Post-Volinskaya, 5 Kiev, UKRAINE
DOWN HG & PG rescue parachute system MANUAL Aeros Ltd. St. Post-Volinskaya, 5 Kiev, 03061 UKRAINE Tel. +(380 44) 455 41 20 Fax. +(380 44) 455 41 16 E-mail: aerosint@aerosint.kiev.ua http://www.aeros.com.ua
More informationCarbon Lite Volleyball system ( Either in packages or components ordered separately )
Instruction Manual VB7222 Carbon Lite Volleyball system ( Either in packages or components ordered separately ) Customer Service (800) 247-7668 P A R T S L I S T Item Qty Description Item Qty Description
More informationS-SERIES 10x10 SETUP INSTRUCTIONS
S-SERIES 10x10 SETUP INSTRUCTIONS THANK YOU FOR PURCHASING A 10x10 S-SERIES TENT! If you have questions about installation, maintenance, or take down, please call us at (800)426-9496. Our goal is that
More informationBowDown. MiniMuM Crossbar spread 24 (61CM) Steel Hook (2X) Buckle Strap (2X) Plastic Tube (2X) Plain Strap (2X) SHORT BLACK T-BOLT (2x) BOWDOWN (2x)
BowDown MiniMuM Crossbar spread 24 (61CM) Heavy Duty strap (2x) SHORT BLACK T-BOLT (2x) BOWDOWN (2x) Bow Stern Tie Down Buckle Strap (2X) Plastic Tube (2X) Plain Strap (2X) Steel Hook (2X) IMPORTANT WARNING
More information/ Tool and Equipment Safety Tether System (T.E.S.T.S)
20 INSTRUCTIONS FOR USE AND PRODUCT GUIDE 799953 / 799955 Tool and Equipment Safety Tether System (T.E.S.T.S) Part # T353012 Rev 2 Reliance Industries LLC 2802 East X Street Deer Park, Texas 77536 281-930-800
More informationAll of these configurations are from one 2005 Blue Ultralite Trayman. Just slide the straps up and over your shoulders and they will slip into place.
All of these configurations are from one 2005 Blue Ultralite Trayman. Just slide the straps up and over your shoulders and they will slip into place. The back edge of the Shoulder Strap has a slight bend
More informationUTV SNOW FORCE TM PUSH TUBE KIT OWNER S MANUAL
1701 38TH AVE W PO BOX 257 SPENCER, IA 51301 PHONE: 712-262-4191 FAX: 712-262-0248 SERVICE: 800-841-2222 E-MAIL: ccac@cyclecountry.com www.cyclecountry.com UTV SNOW FORCE TM PUSH TUBE KIT OWNER S MANUAL
More informationANY HAMMOCK CARRIES INHERENT RISK AND ACCIDENTS MAY OCCUR. USE WITH CAUTION.
www.trailnest.com Roof Top Hammock Stand Owner s Manual WARNING! USING ANY HAMMOCK CARRIES INHERENT RISK AND ACCIDENTS MAY OCCUR. USE WITH CAUTION. MAX LOAD: 250 LBS Congratulations! Thank you for purchasing
More informationNEWMAR SERVICE SCHOOL
NEWMAR SERVICE SCHOOL TRAINING INFORMATION GUIDELINE FOR FEBRUARY 2013 OUR PRODUCTS: NOVA DUAL PITCH AWNING G-2000/ G-1500 2 P a g e G-2085 G-5000 3 P a g e G-LINKS 4 P a g e NOVA/ G-2000/ G-1500 BASIC
More informationImportant! Read all of these instructions before assembling or riding the glider. For questions or help please call Glide Bikes at
Go Glider Manual Congratulations on your purchase of the Go Glider! Your glider is designed for years of nearly carefree use by your child. These instructions include how to set up your glider and maintenance
More informationClevis Style G80 Heavy Duty Tiedowns. Clevlok Style G80 & G100 Heavy Duty Tiedowns
Heavy Duty Tiedowns Meets FMCSA, CVSA tiedown requirements Made from high quality alloy steel Domestic attachments made by CMCO Can not be used for overhead lifting Lighter weight than most transport binder
More informationPL500A Platform Extension
PL500A Platform Extension Operator Manual Copyright 2009 ServerLift Corporation 821 N 2nd Street Phoenix, AZ 85004 VOICE: 602.254.1557 FAX: 602.412.4479 821 N 2nd Street Phoenix, AZ 85004 VOICE: 602.254.1557
More informationInsruction manual Dukki
Insruction manual Dukki Introduction Pg. 1 Product description Pg. 2 3 Assembly and disassembly Pg. 4 Installation and adjustment Pg. 5 12 Maintenance Pg. 13 Parts Pg. 14-17 INDEX 1. Introduction 1 2.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HATCH KIT Application 2009 ELEMENT Publications No. AII 41008 Issue Date DEC 2008 PARTS LIST Tent bag 13 Stakes 4 Guide ropes Tent 2 Awning pole caps Gear loft 2 Tie
More informationF a l l P r o t e c t i o n E x p e r t s. Subject: Buckle Specifications and Operations
Technical Bulletin Subject: Buckle Specifications and Operations DBI/SALA uses four types of buckles in full body harnesses, body belts and other fall protection equipment: parachute buckles, pass through
More informationInstallation and User s Manual 12 x 10 MOTORIZED AWNING
12 x 10 MOTORIZED AWNING Installation and User s Manual 12 x 10 MOTORIZED AWNING 088-1763-0 Stop Please read and understand this manual before any assembly or use of this product. Before beginning assembly
More information2 Tripod System User Guide
2 Tripod System User Guide 1, 2 & 3m 2 Diameter Tripod Systems For use with 3 and 4 diameter masts or stand-alone Lightweight Compact Versatile Components Overview Item Description 4 1 3 x RolaTubes 2
More informationOperating Instructions
Operating Instructions Medium and High Pressure Model Numbers: RT602- RT635- RT602- RT635- RT603- RT650- RT603- RT650- RT605- RT825- RT605- RT650-SM RT802- RT835- RT425- RT803- RT402- RT435- RT625- RT403-
More informationquick and easy installation guide
www.directdriveopener.com quick and easy installation guide Back 2 Front. Motor Carriage 2. C-rail. Chain. Limit stops. Slide in part (tensioner) Rail assembly Insert C-rail parts () into the connecting
More informationX-SERIES 10x10 SETUP INSTRUCTIONS
SETUP INSTRUCTIONS THANK YOU FOR PURCHASING A 10x10 X-SERIES TENT! If you have questions about installation, maintenance, or take down, please call us at (800)426-9496. Our goal is that you are completely
More informationBERYL Service Guide. Travel Adjust OTT Change
BERYL Service Guide Travel Adjust OTT Change SERVICE OVERVIEW This manual will guide you step by step performing a travel adjust and OTT setting change to your Beryl suspension fork. Please follow each
More informationAssembly instructions for Eurotramp trampolines Series: Ultimate, Grand Master Exclusiv, Grand Master, Master
Assembly instructions for Eurotramp trampolines Series: Ultimate, Grand Master Exclusiv, Grand Master, Master 1. Assembly instructions 2. Attaching the plastic coated steel cables on the Ultimate frame
More informationUTV BLADE MOUNT HARDWARE
1701 38TH AVE W PO BOX 257 SPENCER, IA 51301 PHONE: 712-262-4191 FAX: 712-262-0248 SERVICE: 800-841-2222 E-MAIL: ccac@cyclecountry.com UTV BLADE MOUNT HARDWARE For the KUBOTA RTV900 OWNER S MANUAL MODEL
More informationInstallation Instructions Part # 2784 Awning
Please read instructions entirely before installing this product. Parts Included Qty Parts Included Qty 1 Flat Washer (U-Bolt) 4 L Bracket 2 Nylock Nut ( U-Bolt) 4 Stake with Cord 2 6mm x 1 Bolt/Nut 10
More informationSAFETY GUIDELINES FOR DIY TENTS
SAFETY GUIDELINES FOR DIY TENTS Please read carefully and fully before starting assembly of the tent 1. The installer is solely responsible for evaluating the site and proper securing method determined.
More informationHANDLES AND CONTROL CABLES
Worm Drive Transmission........................ 1 Single Speed Spur/Bevel Gear Transmission............. Single Speed Bevel Gear Transmission................ Three Speed Transmission.......................
More informationBR B Bike Rack Instructions
IMPORTANT NOTE: It is common that vehicles with lids and hatches have a single rear wiper. It is important that you make yourself aware that the wiper cannot be used while the rack is attached to the vehicle.
More informationOperating Instructions
Operating Instructions Series RT Spring Driven Hose Reels Low Pressure Model Numbers: RT402-OLP RT605-OLP RT450-OLP RT835-OLP RT403-OLP RT802-OLP RT465-OLP RT850-OLP RT405-OLP RT803-OLP RT625-OLP RT450-OLPSM
More informationROOFTOP CARGO BAG (FRONT OF VEHICLE) HOOK (x4) ATTACHMENT STRAP (x4)
CargoPack, DryTop, SoftTop ROOFTOP CARGO BAG Zipper Flap HOOK (x4) Grab handle ATTACHMENT STRAP (x4) (FRONT OF VEHICLE) Naked roof STRAP (2X) IMPORTANT WARNING IT IS CRITICAL THAT ALL YAKIMA RACKS AND
More informationRAFTER VI. Installation and Operation CAREFREE WITH AUTOMATIC AWNING SUPPORT. RV Accessory PRODUCT OVERVIEW
CAREFREE RAFTER VI RV Accessory WITH AUTOMATIC AWNING SUPPORT Installation and Operation PRODUCT OVERVIEW The gives the awning user the ability to easily tighten the center fabric when the awning is extended.
More informationUSER MANUAL BMU WORKCAGE. CONFORM TO THE MACHINE DIRECTIVE 2006/42/EC and to EN1808 (1999)
USER MANUAL BMU WORKCAGE CONFORM TO THE MACHINE DIRECTIVE 2006/42/EC and to EN1808 (1999) All persons operating this equipment must read and completely understand this manual. Any operation in violation
More informationRoller Bar End Cap (w/round Drive Shaft) Replacement Instructions for Vista and Motorized Awnings * Helpers needed *
RETRACTABLE AWNINGS For Technical Support visit us at www.sunsetter.com/ownerscorner or Call Toll Free 800-670-7071 Fax 877-224-4944 Roller Bar End Cap (w/round Drive Shaft) Replacement Instructions for
More informationTarp Return. Questions? Contact Customer Or Parts Diagrams see Parts and Diagrams section on web at
Roll Rite, LLC and its entire staff would like to not only Thank You but congratulate you on your purchase of one of what we feel to be the finest line of tarping systems in the industry. Tarp Return RR
More informationLBH18BPK. Instruction Sheet
LBH18BPK Instruction Sheet Included: 1. Backpack (includes belt and pouch) 2. Bottle and Hose Attachment Assembly 3. 1 each disposable 1.5 gallon Chemical Storage Bag 4. 1 each 1.5 gallon Warm Water Cleanout
More informationPR-429BF-600M. Bell 429 Blade Fold Kit Operations Manual
Table of Contents Table of Contents... 1 Record of Revisions... 2 References... 3 Introduction... 4 Contact Information... 4 Prerequisites... 5 First Time Use... 6 Blade Clamp Placement... 6 Blade Clamp
More informationReTurn7600. SWL: 205kg/450lbs. SystemRoMedic TM. User manual English. Manual no: 721 Ver
ReTurn7600 User manual English 7600 SWL: 205kg/450lbs Manual no: 721 Ver. 13 150819 ReTurn7600 English ReTurn7600 are used indoors for shorter transfers between wheelchair and bed, wheelchair and toilet/portable
More informationOtter Pro XT Cabin Installation and Set-Up Instructions
Otter Pro XT Cabin Installation and Set-Up Instructions Otter Pro XT Cabin Fits Medium Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro XT Thermal Cabin
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HATCH KIT Application 2014 CR-V Publications No. AII 50018 Issue Date JULY 2013 Put this information in the glove box with the vehicle owner s manual PARTS LIST 4 Guide
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HATCH KIT Application 201 PILOT Publications No. VERSION 1 Issue Date 201 PARTS LIST Stake bag Tent bag 13 Stakes 4 Guide ropes Tent 2 Awning pole caps 2 Tie straps
More informationDO NOT USE WITH CROSSBAR SPREAD LESS THAN 24.
TM Please read all instructions carefully before assembly, installation and/or use of this product. DO NOT USE WITH CROSSBAR SPREAD LESS THAN 24. WARNING: Do not exceed the weight limit of your vehicle
More informationInstallation Guide: Round Trampoline
Trampolines & trampoline parts designed to survive in the harsh Oz climate. www.oztrampolines.com.au Installation Guide: Round Trampoline Safety Tips Here at Oz Trampolines we are passionate about your
More informationOWNER'S MANUAL. ospreypacks.com CLIMBING / MOUNTAINEERING MUTANT SERIES
OWNER'S MANUAL ospreypacks.com CLIMBING / MOUNTAINEERING Designed for fast and light alpine climbing, ice climbing and ski mountaineering, the Mutant Series is great for the vertical enthusiast looking
More informationFLEX KEY ASSEMBLY. ..._ o RAFTER ARM TUBE MAIN ARM TUBE CAP NUT CLAW HINGE
ZIP DEE Inc. 96 Crossen Ave. Elk Grove Village, IL 60007(847)437-0980 (800)338-2378 HEAD CASTING AWNING RAIL FLEX KEY ASSEMBLY..._ o GM1 Installation Instruction GMC Motorhome RAFTER ARM TUBE MAIN ARM
More informationTUCSON PATIO AWNING INSTALLATION MANUAL
TUCSON PATIO AWNING INSTALLATION MANUAL Toll Free 877-792-1775 Fax 877-792-0031 swsuncontrolpro.com sales@swsuncontrol.com 1 INTRODUCTION...3 1.1 Symbols used in this manual... 3 1.2 Personnel requirements...
More informationOtter Pro X-Over Lodge Installation and Set-Up Instructions
Otter Pro X-Over Lodge Installation and Set-Up Instructions Otter Pro X-Over Lodge Fits Magnum Otter II & Pro Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro X-Over Lodge
More information--- BIG LEAGUE BATTING CAGE ---
--- BIG LEAGUE BATTING CAGE --- BGLC-7500 Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev-B Page 1 of 22 IMPORTANT NOTICE: 1. BEFORE
More informationINSTANT GARAGE MODEL NO: CIG81224 ASSEMBLY INSTRUCTIONS PART NO: ORIGINAL INSTRUCTIONS
INSTANT GARAGE MODEL NO: CIG81224 PART NO: 3503578 ASSEMBLY INSTRUCTIONS ORIGINAL INSTRUCTIONS GC1117 INTRODUCTION Thank you for purchasing this CLARKE Instant Garage. When erected, the CIG81224 garage
More informationKontrol Kube Advanced Owners Manual
Mobile Containment. Simplified. TM Kontrol Kube Advanced Owners Manual KONTROL KUBE www.kontrolkube.com 800.343755 1 IMPORTANT SAFETY INFORMATION SAVE THESE INSTRUCTIONS. CAREFULLY READ AND FOLLOW THESE
More informationInstallation Instructions
Installation Instructions Hex Sierra TopTec Products, LLC 7061 Highway 221 Moore, SC 29369 Phone: (800) 845-2830 Fax: (800) 921-7750 e-mail: sales@toptecproducts.com www.toptecproducts.com 2004 TopTec
More informationMYRIAD Banner Stand is a trademark of Skyline Exhibits. Patent Pending PN32294-B. MYRIAD Banner Stand
is a trademark of Skyline Exhibits Patent Pending 1.1 1. Banner Stand Setup 1.1 Remove banner stand from standard case or Arrive Portable Display & Workstation and assemble pole. 1.2 Insert pole into base
More informationAftermarket Installation Manual
Straptek Installation Manual Table of Contents Introduction... 2 Straptek Weight Tension Technology.... 2 Disadvantages with Typical Weight Distribution Systems (WDS)... 2 Straptek Advantages:... 2 Quick
More informationMotorized Oasis Awning RTS Motor Cord Replacement Instructions *Helpers Needed*
RETRACTABLE AWNINGS For Technical Support visit us at www.sunsetter.com/ownerscorner or Call Toll Free 800-670-7071 Fax 877-224-4944 Motorized Oasis Awning RTS Motor Cord Replacement Instructions *Helpers
More informationSolera Classic Awning OEM INSTALLATION MANUAL
Solera Classic Awning OEM INSTALLATION MANUAL TABLE OF CONTENTS System and Safety Information 2 Preparation 3 Resources Required 3 Installation 3 Installing the Awning Rail (If Necessary) 3 Assembling
More informationINSTRUCTION MANUAL ALEKO RETRACTABLE AWNING
INSTRUCTION MANUAL for ALEKO RETRACTABLE AWNING www.alekoproducts.com FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY! 1 Important Safety Precautions WARNING NOTE: FOR PERSONAL SAFETY,
More informationSolar Power Shade INSTRUCTION MANUAL
INSTRUCTION MANUAL 20 June 2006, Revision Initial Release 26 September 2006, version 2 Powerfilm, Inc. 2337 230th Street Ames, IA 50014 (515) 292-7606 Web Site: www.powerfilmsolar.com Table of Contents
More informationGEAR GUIDE CABELA S SET NUMBER:
WEST WIND DOME TENT GEAR GUIDE CABELA S SET NUMBER: 58-0518 WESTWIND 4 PLEASE READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT. VISIT WWW.CABELAS.COM OR CALL 1-800-237-4444 FOR ASSISTANCE.
More information10' x 20' MAX AP CANOPY EXTENSION KIT Assembly Instructions
10' x 20' MAX AP CANOPY EXTENSION KIT Assembly Instructions Frame Not Included Description Model # 10' x 20' MAX AP Canopy - Extension Kit - White 35730 Recommended Tools Please read instructions COMPLETELY
More informationPlease read this manual carefully before your first flight.
Low hangpoint PPG harness User manual Please read this manual carefully before your first flight. Congratulations! Thank you for choosing the Powerseat Comfort harness. We have done our best to present
More informationLM601 Landmark Permanent Blind
LM601 Landmark Permanent Blind Get parts online at www.huntriversedge.com P/N: 26742 REV1: 01/13/17 2017 RETI All Rights Reserved INTRODUCTION Landmark Permanent Blinds are engineered with you the hunter
More informationThanks for shopping with Improvements! 10 Solar Lighted Gazebo Item #531753
Thanks for shopping with Improvements! 10 Solar Lighted Gazebo Item #531753 Parts List: A. Frame Qty: 1 B. Canopy Qty: 1 C. Stake Qty: 8 D. Brace Qty: 4 E. Cap Qty: 1 F. Battery Qty: 2 G. Rope Qty: 4 H.
More informationTable of Contents. Introduction to the AquaTrak AquaTrak Parts List Tank Frame Assembly Pulley System Assembly...
56679 V0309 Table of Contents Introduction to the AquaTrak................................................... 2 AquaTrak Parts List... 3 Tank Frame Assembly... 4 Pulley System Assembly... 6 AquaTrak Maintenance...10
More informationCAPRI PLUS. Instruction Manual. 28' x 38' Including sidewall and connector instructions.
CAPRI PLUS Instruction Manual 28' x 38' Including sidewall and connector instructions STOP Prior to installing any tent, always make sure you check for overhead and underground obstructions! For safe assembly,
More informationCongratulations! WARNING! READ USER MANUAL FIRST! USE AT YOUR OWN RISK!
Congratulations! You just became the owner of the EXIT cutaway harness! We are sure that you will have ton s of fun using this product! Enjoy but use responsible and with care! WARNING! READ USER MANUAL
More informationOWNER'S MANUAL. ospreypacks.com VERTICAL ENDEAVORS VARIANT SERIES
OWNER'S MANUAL ospreypacks.com VERTICAL ENDEAVORS The Variant Series has long been a staple in the Osprey line with targeted design features utilizing feedback from mountain guides, professional alpinists
More informationUser Guide. Tripod. flowtech 75 Tripod. Part No. V
User Guide Tripod flowtech 75 Tripod Part No. V4150-0001 EN www.vinten.com TM Copyright 2017 All rights reserved. Original Instructions: English All rights reserved throughout the world. No part of this
More informationProduct instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E
Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E The Trimfast Ream Cutters are reliable, high performance cutters that will give you the results you need quickly
More informationGeneral Canopy Folding and Packing Instructions for H-X Series Personnel Parachute Canopies. Manufactured by Butler Parachute Systems, Inc.
General Canopy Folding and Packing Instructions for H-X Series Personnel Parachute Canopies Manufactured by Butler Parachute Systems, Inc. Issued 24 July 1998 This set of instructions is for the routine
More informationUrea/Adblue Hose Reel
www.scintex.com.au sales@scintex.com.au Model: SHR3408 Urea/Adblue Hose Reel Product Manual Specifications Spring driven drum: for automatic rewind. Locking ratchet: to maintain the desired length of hose
More informationFEATHER-LITE ROOF TOP TENT SET-UP GUIDE
FEATHER-LITE ROOF TOP TENT SET-UP GUIDE TENT031 INSTALL TIME: 30 minutes 0 GET ORGANIZED you will need: D Your Tent D The Ladder (in a separate box) D A Power Drill w/ Phillips screw bit D A solid, scratch
More informationPACKING INSTRUCTIONS for the Strong Enterprises. Military Tandem Tether Bundle MTTB. Canopy Part No
PACKING INSTRUCTIONS for the Strong Enterprises Military Tandem Tether Bundle MTTB Canopy Part No. 420709 Manual No. 510055 REV: B May 2004 Parachuting is a hazardous activity that can result in serious
More informationCOMBI CRATE MODEL NO: 7000/7001/7002/7003
COMBI CRATE MODEL NO: 7000/7001/7002/7003 Owner s Manual READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE KEEP INSTRUCTIONS FOR FUTURE USE. Carlson Pet Products,Inc 14305 Southcross Drive,Suite 105,
More information4812 HEAVY BAG STAND OWNER S MANUAL
48 HEAVY BAG STAND OWNER S MANUAL Note:Warning Labels Everlast Worldwide, 00 Hwy DD, Moberly, MO 65270 Customer Service 800.821.7930 14 C4 48 HEAVY BAG STAND OWNER S MANUAL CONGRATULATIONS! YOU HAVE JUST
More information4.2 Assembly Instructions
4.2 Assembly Instructions 4.2.1 Assembly of Reserve Canopy. Assembly of Reserve Canopy using Rapide Links. After inspecting the Parachute and the Wings Harness/Container System, hang or lay the parachute
More informationRUPHIS Blade Clamp. Instruction Manual
RUPHIS Blade Clamp P/N 1006800 NSN 1615-01-562-8156 Instruction Manual AH-64D UH-60A/L UH-60M S-70i S-92 REVISION AUTHORIZATION / RECORD These instructions are primarily for inspection of the RUPHIS Blade
More information300 ft. 5/8 Hose wagon
300 ft. 5/8 Hose wagon Model 95956 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. (Garden hose is not included).
More informationA A A T E C H N O L O G Y
A A A T E C H N O L O G Y & SPECIALTIES CO., INC. H A R D W A R E C A T A L O G TOTAL SOLUTION SERVICE For the Industrial Piping Marketplace 2011 www.aaatech.com 4 0 Y E A R S S E R V I N G I N D U S T
More informationRhino-Rack SUNSEEKER II Awning 2.0 metres (32109)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationINSTALLATION INSTRUCTIONS AND OWNER'S MANUAL AWNINGS. For trailers & motor homes with straight sides TOOLS REQUIRED
AWNINGS INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL For trailers & motor homes with straight sides TOOLS REQUIRED 1/4" electric drill Ratchet handle kit 3/8" & 7/16" socket No. 1 and No. 2 screwdriver
More informationRhino-Rack SUNSEEKER II Awning
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More information33100 LH - Batwing Awning RH - Batwing Awning
33100 LH - Batwing Awning 33200 RH - Batwing Awning 1. Check Part No./Kit is correct 3. Fit roof rack accessory 2. Read through instruction before installing 4. Check and recheck all fasteners are secure
More informationRESCUE SUPPORT SYSTEMS TRIPOD CONVERSION KIT PN
RESCUE SUPPORT SYSTEMS TRIPOD CONVERSION KIT PN 22-796300 Paratech Incorporated Paratech Europe, Branch of Paratech Inc. P.O. Box 1000, Frankfort, IL 60423 USA P.O. Box 174, 5260 Odense S, Denmark Customer
More informationfunctionality with the necessary maintenance tools stored in a convenient built in tool box, as well as parallel handles for
GuilloMax User Manual The Guillomax has distinct features such as its unique structure and ease of cutting. It combines symmetry with functionality with the necessary maintenance tools stored in a convenient
More informationDC 700 Series Hose Reel - September 2010
Instructions Parts List Service Manual DC 700 Series Hose Reel - September 2010 Suitable for dispensing, transfer and evacuation of lubricants, fuels, air & other automotive & industrial products. To be
More informationInstallation & Operation Manual VHM Variable Height Series Arms with Fixed Angle Front End
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation & Operation Manual VHM Variable Height Series Arms with Fixed Angle Front End Products covered
More informationINSTRUCTION SHEET DETHATCHER KIT. STS-422LX LPSTS-42JD Assembly Installation Operation Repair Parts L-1660-D. Visit us on the web!
INSTRUCTION SHEET DETHATCHER KIT MODEL: DK-422LX FOR USE WITH SWEEPER MODEL: STS-422LX LPSTS-42JD Assembly Installation Operation Repair Parts For use with Riders and Lawn/Garden Tractors For the latest
More informationNOTICE: Once used, this shelter cannot be returned to the store. If you have a warranty claim, please contact Clam Corporation directly.
Model No. - 8235 - p/n 108440 S p e c i f i c a t i o n s H e i g h t - 75 (24 packed) Width - 7 5 Depth - 144 (45 packed) W e i g h t 155 lbs. - Clam Customer Service Information - NOTICE: Once used,
More informationAdvantage Plus TIM-3600 Series Reel
Read the following precautions and instructions before you begin assembly or using. Failure to comply with these instructions could result in personal injury or property damage. Keep these instructions
More informationBigStack. Minimum Crossbar spread 24 For factory racks: Check fitlist notes, or Yakima.com for your vehicle s crossbar spread.
BigStack Minimum Crossbar spread 24 For factory racks: Check fitlist notes, or Yakima.com for your vehicle s crossbar spread. HEAVY Duty strap (2x) PAD (4x) ADJUSTMENT KNOB (2x) T-BOLT (2x) BAIL (2x) BigStack
More informationSafety Tips. Welcome. Contents. Care & Maintenance
Safety Tips Welcome At Oz Trampolines, we are passionate about your family s safety when using our trampolines and accessories. We have put together a list of safety tips and advice which will help ensure
More informationGeneral Purpose Shelter
General Purpose Shelter 0' x 0' x ' ( x x. m) ASSEMBLY MANUAL Model NO.: - Tools required for assembly (not included) TM TABLE OF CONTENTS Important safety instructions... Intended use... Parts list......
More informationIMPORTANT INFORMATION DO NOT DISCARD
KAYE Products, Inc. IMPORTANT INFORMATION DO NOT DISCARD Medium Harness (Model 9822) & Large Harness (9824) Each package should contain the following: The materials will come packed as pictured below:
More information