Square Lashing. Frapping this tightens the lashing. Wind the twine between the two sticks three times, pulling tightly as you go.

Transcription

1 Square Lashing Square Lashing can be used to bind long sticks at right angles to trees or poles to form drying racks and for many other uses. You begin with a clove hitch on one upright stick (or tree) leaving enough of a tail to tie a square knot when this portion of lashing is complete. Cross the other stick at right angles over the first stick (tree). Cross the twine over the cross stick and behind the upright stick, then back over the cross stick and under the upper part of the upright stick. Continue this 4 times, keeping the twine neat, even, and tight. When you ve finished all sides with four rounds, now you frap three times between the sticks and finish with a square knot, using the end piece from your original clove hitch. Frapping this tightens the lashing. Wind the twine between the two sticks three times, pulling tightly as you go.

2 Continuous Lashing Continuous Lashing is probably the most fun of all the lashing techniques. It requires two to three people to complete successfully. It is useful in creating shelves, dishwashing stations, tables, and many other wonderful structures in your campsite. If you want to make a shelf or dishwashing station, you begin by square lashing two long poles between two trees (if you don t have trees, you will need to make legs for the ends and square lash the poles to the legs. Now begins the continuous part. You will need lots of small sticks (notching isn t required) to create your shelf on the two long poles. If you have three people working, two will wrap twine and one will feed the sticks between wraps. Measure twine that is about 4-5 times the length of your finished structure for each person wrapping. Find the center and wrap the twine around each hand. Using this center, tie a clove hitch around the cross pole for each side. The third person now lays a stick between the two poles. Working together, each person wrapping goes over the pole (one hand inside the poles, one outside), down under the pole, making a cross (switch bundles to opposite hands while underneath). Each person continues working in unison, bringing the twine up, over another stick, down, and cross, until your shelf is complete. End the lashing with a square knot. The design possibilities for this type of lashing are endless.

3 Round, Shear, Tripod Lashing Round Lashing is used when you need to make a pole longer. Place two poles so the ends overlap (remember, you are trying to make a longer pole). Place a clove hitch around both poles at one end where they overlap. Begin winding the twine around both poles until you reach the other end where they overlap. If you ve done this tightly enough, you will not be able to frap this type of lashing. Finish the wrapping with a clove hitch. For extra strength, overlap the poles a longer distance and have two sets of round lashing where each of the ends overlap, rather than one continuous lashing. Shear Lashing adds frapping between the poles. With tight frapping, it can join two poles like round lashing. Looser frapping is a great way to create an A-frame with two poles. It is lashed very much like round lashing above, but not as tightly. Lay two poles side by side and clove hitch around one pole. Make four or more wraps around both poles, somewhat loosely. Frap three times between the poles, tie a square knot with the original clove hitch end, and raise as an A-frame.

4 Tripod Lashing is lashed as for shear lashing, but using three poles. This is useful in creating a tripod for a washbasin, lantern stand, a teepee shelter, or even for growing beans in your garden. Place three poles next to each other, overlapping by 4-5- inches, with the middle one pointing the opposite direction. Tie a clove hitch around an outside pole and loosely wrap all three poles 5 to eight times. Frap loosely on either side of the middle pole and tie with a square knot to the clove hitch tail. As you spread the legs of your tripod out, the lashing will become tight. This type of lashing takes some practice to get the right tension and distance between poles. If your tripod will not spread enough, start again and leave more space between the poles and more slack in the twine.

5 Diagonal Lashing Diagonal Lashing may be used to create a freestanding structure. Begin by crossing two sticks into an X. Make a clove hitch around both sticks where they cross, again leaving a tail to finish with a square knot. Wind the twine tightly four times through one half of the X. Now do the same through the other half of the X. Frap three times between the sticks and tie a square knot with the clove hitch tail.