CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-742 Rotary Cutter ~ The World's Largest Rotary Cutter ~

Transcription

1 CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-742 Rotary Cutter ~ The World's Largest Rotary Cutter ~ CUTTER FEATURES - 42ft Cutting Width (12.8 m) - 250hp Minimum Tractor Size - Hydraulic Phasing & Mechanical Hybrid - 2" - 16" Cutting Height ( mm) - Floating Hitch Lift System with Hydraulic Depth Control - 118" Transport Width (3m) - 10 Gearbox Layout with - Adjustable Wheel Standards - 10 ga Domed Deck (3.4 mm) - 7 Slip Clutches (7 down clutches) - 1 Year Full Warranty & 3 Years - Replaceable 2 Piece Skid Shoes - 18,000 lbs Total Weight (8,165 kgs) Limited Gearbox Warranty - 2" Cutting Capacity (51 mm) - Easy to Use Safety Lock Up HOW TO ORDER: You must select from Sections 1-5 to receive a complete rotary cutter ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Price CDN Wt/kgs C FX742 Rotary Cutter 104, S Safety Light Kit (Required) ~ ~ Selection 2 ~ Choose Axle and Tire Configuration~ ~ C Through Axle Kit -Choose 10 Tires 6, C Walking Axle Kit - Choose 14 Tires 9, ~ ~ Selection 3 ~ Choose Axle Tire Option ~ ~ WG Tire Assembly 11L Stubble Proof (Choose Quanity of Tires Needed 10 or 14) ~ ~ Selection 4 ~ Choose a Blade Configuration ~ ~ C Pan Kit with Updraft Blades 6, C Pan Kit with Updraft Blades & Shredder Kit 7, C Fixed Knife Kit with Flat Double Sided Blades & Shrouds 8, ,600 C Fixed Knife Kit with Updraft Blades & Shrouds 8, Assembly charge on pan units 1, Assembly charge on fixed blade units 1, ~ ~ Selection 5 ~ Choose a Safety Guard & Accessories ~ ~ C Single Chains Front & Rear 3, C Front & Rear Rubber Belting 1, C Single Chains Front & Rear with Front Rubber Belting 3, PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

2 S CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-742 Rotary Cutter ~ The World's Largest Rotary Cutter ~ ~ ~ Selection 5 ~ Choose Wheel Extension Kit ~ ~ Price CDN Wt/kgs 68 C Row Crop Wheel Extensions (Will accommodate 30", 32", 36", 38", 40" + 1m rows) (Transport width of 146" or 3.7m) NOTE: All Tires Are 11L x 15 x 12 Ply Rated ~ ~ Selection 6 ~ Choose a Destination Code ~ ~ C742-NA North American Destination Kit ~ ~ Selection 7 ~ Options~ ~ C Fan Debris Kit, Factory Installed 7, C Fan Debris Kit, Crated 7, C HYD Cooler Factory Installed 4, C HYD Cooler Factory crated 4, IMPORTANT: Safety Tow Chain Kit must be used at all times when moving equipment on any type of road. IMPORTANT: OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown Object Shield Information Message in the Rotary Cutter Spec Section in the sales price book. PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

3 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-530 ROTARY CUTTER CUTTER FEATURES - 30' of mowing and shredding excellence - Phasing system for parallel lift cut - Accommodates 30",32", 36", 38" row spacings - Non-adjustable clutches provide low - Spun formed pans available on pan uint maintenance -Excellent shredding and distribution capabilities -Available Cyclone Deck Debris Fan Kit on Fixed Knife units -350 hp, 60 deg splitter gearbox allows for - Unique drive layout allows for clutch on every Unique driveline layout down box - Floating hitch with rubber grommet rear suspension ~ ~ Selection 1 ~ Choose a Basic Unit, Drive Package ~ ~ Price CDN WT(kgs) 1) C Schulte FX-530, Basic Unit (Required) 52, ) S Safety Light Kit (Required) ~ ~ Selection 2 ~ Choose a Hitch Option ~ ~ C Trailing Hitch, CV Style Required 1, Choose a Shaft WG 1 3/4 inch Tractor Shaft 1, WG 1 3/8 inch Tractor Sahft 1, ) C Trailing Equal Angle Hitch Sub Assembly 2, Must Choose a Hitch Block a) C Category 3, fits up to a 1-1/2 pin and a drawbar 2-1/4 x 3-1/ b) C Category 4, fits up to a 2 pin and a drawbar 2-1/2 x 5-1/ c) C Category 5, fits up to a 2-3/4 pin and a drawbar 3-1/8 x 6-1/ Choose a Tractor Shaft: IMPORTANT : PTO Adaptor must not be used in any application. a) WG Equal Angle Shaft, 1 3/8" x 21 Spline b) WG Equal Angle Shaft, 1 3/4" x 20 Spline

4 CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-530 ROTARY CUTTER Subject to GST ~ ~ Selection 3 ~ Choose an Extension Kit ~ ~ 170 C Row Crop Extensions (not required with FLX1510) ~ ~ Selection 4 ~ Choose an Axle Kit~ ~ C NON WALKING WHEEL STANDARDS (Choose 8 TIRES) 4, C WALKING AXLES (choose 10 TIRES) 6, C Standard Axle Add-on (Choose 2 tires) 1, ~ ~ Selection 5 ~ Choose Tire Kit~ ~ WG Light Truck Tires (Choose quanity of tires needed 8, 10 or 2) WG Tire Assembly 11L Stubble Proof (Choose quanity of tires needed 8, 10 or ~ ~ Selection 6 ~ Choose a Pan or FIxed Knife Kit ~ ~ C Pans and Updraft Blades 4, C Fixed Knife Kit c/w Shrouds and Updraft Blades 4, C Fixed Knife kit c/w Shrouds and Non Updraft Blades 4, ~ ~ Selection 7 ~ Choose a Shielding Kit or Combination ~ ~ C Front Single Chains C Rear Single Chains 1, C Front Double Chains 1, C Rear Double Chains 1, C Half-length front belting C Half-length rear belting C Front Belting C Rear Belting

5 CANADIAN Subject to GST MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-530 ROTARY CUTTER ~ ~ Selection 8 ~ Choose Destination Kit ~ ~ C530-NA North American ~ ~ Selection 9 ~ Choose Options ~ ~ C Hydraulic Actuated Outer Wings 1, C Crop Divider New Option Schulte Cyclone Fan Kits C Fan Debris Kit, Factory Installed 7, C Fan Debris Kit, Crated 7, C HYD Cooler Factory Installed 4, C HYD Cooler Factory Crated 4, IMPORTANT: Assembly Charge on Pan Units Assembly Charge on Fixed Blades 1, ) Safety Chain Kit must be used at all times when moving equipment on any type of road. 2) PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown Object Shield Message in the Rotary Cutter Spec section in sales price book.

6 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, Rotary Cutter CUTTER FEATURES - 10GA deck - Spring steel bushings at major - S safety chain kit 1/4" grade 70 - Phasing cylinders (3) c/w hoses pivot points with 10,000 lbs capacity - Wing lift cylinders (2) c/w hoses RPM - Two piece replaceable skid shoes - Suspension for center and wings - Deck protection rings - Operator's manual in holder HOW TO ORDER: You must select from 1-6 to receive a complete rotary cutter including standard features. To receive additional options, choose from selection 7. Price CDN ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Wt/kgs 1) C Basic 26' Unit, 1000 RPM 46, ) S Safety Light Kit (Required) ~ ~ Selection 2 ~ Choose a Hitch Type and Accessories ~ ~ 1) C Trailing hitch, CV Style Choose a Clevis: a) C WG Solid Tongue b) C WG Open Clevis c) C WG Precision hitch d) C WG Clevis with 2 3/16" Opening f) C WG Adjustable Clevis Choose a Tractor Shaft: a) WG CV Shaft, 1 3/4" x 20 Spline 1, b) WG CV Shaft, 1 3/8" x 21 Spline 1, ) C Trailing Equal Angle Hitch Sub Assembly 1, Must Choose a Hitch Block a) C Category 3, fits up to a 1-1/2 pin and a drawbar 2-1/4 x 3-1/ b) C Category 4, fits up to a 2 pin and a drawbar 2-1/2 x 5-1/ c) C Category 5, fits up to a 2-3/4 pin and a drawbar 3-1/8 x 6-1/ Choose a Tractor Shaft: IMPORTANT : PTO Adaptor must not be used in any application. a) WG Equal Angle Shaft, 1 3/8" x 21 Spline b) WG Equal Angle Shaft, 1 3/4" x 20 Spline ) C Parallel Ring hitch 1, (Required) WG Pintle Ring, Forged,PT-48 (installed on Parallel hit Choose a Tractor Shaft: a) WG CV Shaft, 1 3/4" x 20 Spline 1, b) WG CV Shaft, 1 3/8" x 21 Spline 1, PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

7 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, Rotary Cutter ~ ~ Selection 3 ~ Choose a Blade Configuration ~ ~ Price CDN Wt/kgs 1) C Two Blade Pan Kit 4, ) C Two Blade Pan Kit with Shredder Blades 4, ) C Fixed Knife Shredder Kit with Updraft Blades 6, ) C Fixed Knife Shredder Kit with Flat Blades 6, (recommended for Irrigated cotton) Assembly charge on pan units Net Assembly charge on fixed blade units Net ~ ~ Selection 4 ~ Choose a Safety Guard & Accessories ~ ~ 1) C Single Safety Chains Front & Rear c/w Front Rubber Belting 2, (recommended for cotton & corn) 2) C Single Safety Chains Front Only c/w Front & Rear Rubber Belting 1, (recommended for dry grass staw, wheat straw & barley straw) 3) C Single Safety Chains Front & Rear c/w frt & rear belting 2, ) C Single Safety Chains Front & Rear 1, a) C Cable Through Chains (optional for C & C ) ) C Double Safety Chains Front & Rear 2, a) C Cable Through Chains (optional for C & C ) IMPORTANT: OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown Object Shield Information Message in the Rotary Cutter Spec Section in the sales price book. PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

8 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, Rotary Cutter ~ ~ Selection 5 ~ Choose Axle Option ~ ~ Price CDN Wt/kgs 1) C Standard Axle Kit (Choose 6 tires) 2, ) C Standard Axle Kit (choose 8 tires) 3, ) C Walking Axle Kit (Choose 8 Tires) 4, ) C Walking Axle Kit (Choose 8 tires) 6, ~ ~ Selection 6 ~ Choose Tire Kit~ ~ 5) NRWG Used Aircraft Tire (Choose quanity of tires needed 6 or 8) ) WG Light Truck Tire (Choose quanity of tires needed 6 or 8) ~ ~ Selection 7 ~ Schulte Fan Kit ~ ~ 1) C Fan Debris Kit, Factory Installed 7, ) C Fan Debris Kit, Crated 7, ~ ~ Selection 8 ~ Choose a Destination Code ~ ~ Please select the destination of the cutter for proper Decals and Manuals. 1) C502-NA North America and Australia Destination Kit ) C502-UK United Kingdom Destination Kit ) C502-FR France Destination Kit ) C502-SE Sweden Destination Kit ) C502-DE Germany Destination Kit ) C502-RU Russia Destination Kit ) C502-UA Ukraine Destination Kit PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

9 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, Rotary Cutter ~ ~ Selection 9 ~ Extra Options ~ ~ S Safety Light Kit C Crop Dividers C HYD Cooler Factory Installed 4, C HYD Cooler Factory Crated 4, IMPORTANT: When moving equipment on any type of road, if the rotary cutter obscures the tractor warning or tail lights, the cutter must be equipped with the S Safety Light Kit PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

10 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-520 Rotary Cutter SPECIFICATIONS - Overall Width " (6.2m) - Transport Width " (2.32m) - Min. Tractor Size hp (75kw) - Overall Length " (6.15m) - Transport Height " (3.05m) - Blade Tip Speed ,000 ft/min - Cutting Height --- 2" " - Cutting Capacity --- 2" (51mm) - Blade Overlap --- 6" (153mm) (Depending on Tire Size) 2" (51mm) Fixed Knife - Deck Thickness " (7 ga) (4.6mm) - Cutting Width " (6.10m) 4" (102 mm) Pan Unit HOW TO ORDER: You must select from 1-6 to receive a complete rotary cutter including standard features. To receive additional options, choose from selection 7. Price CDN ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Wt/kgs 1) C Basic 20' Unit, 1000 RPM 36, ,368 2) S Safety Light Kit (Required) ~ ~ Selection 2 ~ Choose a Hitch Type and Accessories ~ ~ 2) C Trailing hitch, CV Style 1, Choose a Clevis: a) C WG Solid Tongue b) C WG Open Clevis c) C WG Precision hitch d) C WG Adjustable Hitch e) C WG Solid Tongue with 2-3/16" hole for 2" pin d) C WG Clevis with 2 3/16" Opening Choose a Tractor Shaft: a) WG CV Shaft, 1 3/8" x 21 Spline 1, b) WG CV Shaft, 1 3/4" x 20 Spline 1, ) C Parallel Ring hitch (For European Applications Only) 1, a) WG Shaft, 1 3/8" x 6 with Over-Running Clutch 1, ) C High hitch (For Germany Only) 1, Choose a Tractor Shaft: a) AWG CV Shaft, 1 3/8" x 21 Spline 1, b) AWG CV Shaft, 1 3/4" x 20 Spline 1, Assembly charge on pan units Net Assembly charge on fixed blade units Net PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

11 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-520 Rotary Cutter ~ ~ Selection 3 ~ Choose a Blade Configuration ~ ~ Price CDN Wt/kgs 1) C Pan Kit with Updraft Blades and Shrouds 3, ) C Pan Kit with Shredder Blades and Shrouds 3, ) C Fixed Knife Shredder Kit with Updraft Blades & Shrouds 5, ) C Fixed Knife Cotton Kit with Flat Blades & Shrouds 4, ~ ~ Selection 4 ~ Choose a Safety Guard and Accessories ~ ~ 1) C Single chains front and rear 1, a) C Half Length Front Belting (Must be used with a chain option) ) C Double chains front and rear 1, a) C Half Length Front Belting (Must be used with a chain option) IMPORTANT: OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown ~ ~ Selection 5 ~ Choose Axle and Tire Option ~ ~ 1) C Standard 318 Axle kit (Choose 4 Tires) 3, ) C Axle Kit c/w Center duals (choose 6 Tires) 4, ) C Axle Kit c/w Center Walking (choose 6 Tires) 4, ) C Dual Axle Kit (Choose 8 Tires) 4, ) C Walking Axle kit (Choose 8 Tires) 5, ) C Center Walking Axle c/w Duals on Wings (Choose 8 Tires) 4, ~ ~ Selection 6 ~ Choose Axle and Tire Option ~ ~ 7) WG Tire Assembly 11L Stubble Proof (Choose quanity of tires needed 4, 6 or 8) ) NRWG Used Aircraft Tire (Choose quanity of tires needed 4, 6 or 8) ) WG Light Truck Tire (Choose quanity of tires needed 4, 6 or 8)

12 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-520 Rotary Cutter ~ ~ Selection 7 ~ Choose a Destination Code ~ ~ Please select the destination of the cutter for proper Decals and Manuals. Price CDN 1) C520-NA North America and Australia Destination Kit ) C520-UK United Kingdom Destination Kit ) C520-FR France Destination Kit ) C520-DE Germany Destination Kit ) C520-RU Russia Destination Kit ) C520-UA Ukraine Destination Kit ~ ~ Selection 8 ~ Schulte Fan Kit ~ ~ 1) C Fan Debris Kit, Factory Installed 7, ) C Fan Debris Kit, Crated 7, ~ ~ Selection 9 ~ Extra Options ~ ~ 2) C Crop Divider IMPORTANT: When moving equipment on any type of road, if the rotary cutter obscures the tractor warning or tail lights, the cutter must be equipped with the S Safety Light Kit PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER Wt/kgs 14

13 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-318 ROTARY CUTTER CUTTER FEATURES - North America's First 18' Flex Wing Mower Equal angle non cv drive - 540/1000 RPM 80⁰ CV Drive - Height Control Cylinder & Hoses - Replaceable Skid Shoes -Wing Lift Cylinders & Hoses - 7 ga Single Domed Deck and Stump Jumpers " to 16.75" (44.5mm to 425mm) Cutting Height - Rubber 3 Puck Grommet Suspension - Operator's and Parts Manual Holder - 90 HP Recommended Tractor - Over Center Folding Wings - Cutting Width 216" (5.5m) - Transport Width (max with duals on wings) 96"(2.4m) more specs on brochure ~ ~ Selection 1 ~ Choose a Basic Unit, Drive Package ~ ~ Price CDN WT(kgs) C Schulte FX-318, Basic Unit 14, S Safety Light Kit (Required) Choose a Drive Package: a) C Drive Package, CW Center, 540 RPM 5, in base b) C Drive Package, CW Center, 1000 RPM 5, in base Note: It using Equal Angle Hitch Skip to Selection 3 C Trailing Hitch, CV Style Required Choose a CV Shaft: a) WG CV Shaft, 540 RPM 1, b) WG CV Shaft, 1000 RPM 1, c) WG CV Shaft 1000 RPM 1 3/4" shaft 1, Choose a Clevis ~ ~ Selection 2 ~ Trailing Hitch ~ ~ CS01-106WG Open Clevis (Minimum Requirments) C WG Adjustable Clevis C WG Precision hitch C WG Solid Tongue ~ ~ Selection 3 ~ Equal Angle Clevis ~ ~ C Equal Angle Hitch Kit w/ 540 RPM Shaft c/w Non CV Drive Shaft 2, PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

14 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-318 ROTARY CUTTER ~ ~ Selection 4 ~ Choose a Chain Guards ~ ~ C Chain Guards Single Front and Rear C Chain Guards Double Front and Rear 1, C Front Half Belting (Must be used with a chain option) C Rear Half Belting (Must be used with a chain option) ~ ~ Selection 5 ~ Choose a Pan Kit ~ ~ C Pan Kit (required) 1, ~ ~ Selection 6 ~ Choose a Blade Configuration ~ ~ C Updraft Blades, CW Center C Shredder Blades, CW Center (optional) ~ ~ Selection 7 ~ Choose a Both Wheel Standard Kits ~ ~ C Wing Wheel Standard, 1 or 2 Tires Required 1, C Dual Wheel Standard on the Center Required 1, ~ ~ Selection 8 ~ Choose a Axle Kit ~ ~ C Axle Kit for 4 Tires C Axle Kit for 6 Tires C Axle Kit for 8 Tires 1, ~ ~ Selection 9 ~ Choose a Tire Option ~ ~ Please state the quantity of tires that you would like to order as the numbers listed below are single tires and not tire kits WG Solid Laminated Tires, 6 x 9 x WG Forklift Tire 6.5 x ply on 2 pce 5 bolt rim WG Tire 24x Ply Severe Duty FWG Tire 24x Ply Severe Duty Foam Filled PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

15 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-318 ROTARY CUTTER ~ ~ Selection 10 ~ Choose a Destination Code ~ ~ C318-NA North American & Australian Decal Kit ~ ~ Selection 11 ~ Choose Extra Options ~ ~ C Crop Dividers (Used in Cotton) Assembly Charge on Pan Units PDI PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER IMPORTANT: 1) Safety Chain Kit must be used at all times when moving equipment on any type of road. 2) OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown Object Shield Message in the Rotary Cutter Spec section in sales price book.

16 S CANADIAN MACHINE PRICES AND SPECIFICATIONS Subject to GST Effective July 2, 2016 FX-315 ROTARY CUTTER STANDARD & OPTIONAL CUTTER FEATURES - 7GA deck - Residue distribution tailboard - Replaceable deck protection rings - Transport width of 99" - Variable position shrouding - Single domed, sweep clean deck - 4 gearbox drive layout - Fixed knife technology - Two piece replaceable skid shoes - Optional belting front or rear - Category 5 & 6 drivelines - Pentagon blade bolt design - Hyd Phasing lift system - Rubber suspension - standard - Optional dbl safety chains front or rear Hubs and axles - Speed levelling system - Full floating front hitch HOW TO ORDER: You must select from 1-8 to receive a complete rotary cutter including standard features. To receive additional options, choose from selection 9. ~ ~ Selection 1 ~ Choose a Basic Unit, Drive Package & Back Beam ~ ~ Price CDN Wt/kgs 1) C FX-315 Rotary Cutter 17, ,650 2) S Safety Light Kit Choose a Drive Package: a) C Drive Package, CW Center, 540 RPM 6, b) C Drive Package, CW Center, 1000 RPM 6, Must Choose the Center Back Beam 1) C Standard Back Beam 1, ~ ~ Selection 2 ~ Choose a Hitch Type and Accessories ~ ~ 1) C Trailing CV hitch Kit Choose a Clevis: a) CS01-106WG Open Clevis b) C WG Adjustable Clevis (Not Required with FLX15 or FLX10) c) C WG Precision hitch d) C WG Solid Tongue (Not Required with FLX15 or FLX10) e) C WG Clevis with 2 3/16" Opening Choose a Tractor Shaft: a) WG CV Shaft, 540 RPM 1, b) WG CV Shaft, 1000 RPM 1, ) C Equal Angle Non-CV hitch Kit w/ 540 RPM Shaft 2, ) C Parallel Ring hitch 1, a) WG Pintle Ring, Forged,PT-48 (installed on Parallel hitch) Choose Tractor Shaft b) WG CV Shaft, 1000 RPM 1, ) C German high hitch 1, a) WG Pintle Ring, Forged,PT-48 (installed on Parallel hitch) Choose Tractor Shaft b) WG CV Shaft, 1000 RPM 1,

17 S CANADIAN MACHINE PRICES AND SPECIFICATIONS FX-315 ROTARY CUTTER Subject to GST Effective July 2, 2016 ~ ~ Selection 3 ~ Choose a Skid ~ ~ Price CDN Wt/kgs 1) C Regular Skids ~ ~ Selection 4 ~ Choose a Safety Guard Kit ~ ~ 1) C Chain Guards Double Front NOTE: Any combination of chains 1, ) C Chain Guards Double Rear & belting can be used ) C Full Front Belting NOTE: When ordering Residue 4) C Full Rear Belting Distribution Tailboard NO rear guards are needed 5) C Residue Distribution Tailboard 2, (recommended with C ) IMPORTANT: Safety Tow Chain Kit must be used at all times when moving equipment on any type of road. IMPORTANT: OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown ObjectShield Information Message in the Rotary Cutter Spec Section in the sales price book.

18 S CANADIAN MACHINE PRICES AND SPECIFICATIONS FX-315 FX315 ROTARY CUTTER Subject to GST Effective July 2, 2016 ~ ~ Selection 5 ~ Choose Pan Kit or Fixed Knife Blade Configuration ~ ~ Price CDN 1) C Pan Kit 1, Choose a blade configuration a) C Updraft Blades, CW Center b) C Shredder Blades, CW Center Wt/kgs Optional a) C Bolt-On Deck Ring Option for Pan Kit ) C Fixed Knife Bars, Blades (Updraft), Mounts, CW Rotation on Center 2, ) C Variable Position Shrouding (recommended with C ) 1, ~ ~ Selection 6 ~ Choose An Axle Kit ~ ~ 1) C Axle Kit for 4 Tires ) C Axle Kit for 6 Tires 1, ) C Axle Kit for 8 Tires 2, ~ ~ Selection 7 ~ Choose A Tire Option ~ ~ 1) WG Solid Laminated Tire, 6 x 9 x ) WG Tire 24x Ply Severe Duty ) FWG Tire 24x Ply Severe Duty Foam Filled ) WG Tire Assy, Forklift, 6.50x10-10 Ply Rated on 2pce 5 Bolt Rim PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

19 S CANADIAN MACHINE PRICES AND SPECIFICATIONS Subject to GST Effective July 2, 2016 FX-315 ROTARY CUTTER ~ ~ Selection 8 ~ Choose a Destination Code ~ ~ Please select the destination of the cutter for proper Decals, Manuals and CE Shielding Upgrade. Price CDN 1) C316-NA North American English Destination Kit Wt/kgs 2) C316-FR France Destination Kit ) C316-DE German Destination Kit ~ ~ Selection 9 ~ Extra Options ~ ~ 1) C Chock Blocks ) C Light Mount Plates, France IMPORTANT: When moving equipment on any type of road, if the rotary cutter obscures the tractor warning or tail lights, the cutter must be equipped with the S Safety Light Kit Assembly Charge Net Optional Factory PDI Net OPTIONAL PDI INCLUDES: greasing of all pivot points, gearbox oil checked, charge hydraulic cylinders and install pioneer ends. Tires will be installed where necessary. It is the dealers responsibility to remove shipping brackets & banding as well as to adjust mower height as specified in the operators manual. Please go to the Schulte website/dealer access for further information. PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

20 S CANADIAN MACHINE PRICES AND SPECIFICATIONS Subject to GST Effective July 2, 2016 XH1500 Series 4 Rotary Cutter CUTTER FEATURES - 7GA deck - Single domed, sweep clean deck - S safety chain kit 1/4" grade 70 - Two piece replaceable skid shoes - Rubber suspension - standard with 10,000 lbs capacity - Double safety chains front & rear - Four gearbox drive layout - 1/4" Round skid pans (Stump Jumpers) - Walking axles on center section 210hp down, 260hp splitter c/w 6 updraft blades - Hydraulic phasing lift system - Full floating front hitch - Pentagon blade bolt design - Hydraulic wing lift system - Inboard rotation - Operator's manual in holder Hubs and axles - Deck protection rings HOW TO ORDER: You must select from 1-7 to receive a complete rotary cutter including standard features. To receive additional options, choose from selection 7. ~ ~ Selection 1 ~ Choose a Basic Unit and Drive Package ~ ~ Price CDN Wt/kgs 1) C Basic 15' Unit, S required in North America, but needed with FLX , ,175 2) S Safety Light Kit (Required) Choose a Drive Package: a) C CW Rotation on Center, 540 RPM 6, b) C CCW Rotation on Center, 540 RPM 6, c) C CW Rotation on Center, 1000 RPM 5, d) C CCW Rotation on Center, 1000 RPM 5, ~ ~ Selection 2 ~ Choose a Hitch Type and Accessories ~ ~ 1) C Trailing Hitch CV Style 1, Choose a Clevis: a) CS01-106WG Open Clevis (Minimun Requirement) b) C WG Adjustable Clevis c) C WG Precision Clevis (not required with FLX-1510) d) C WG Solid tongue (not required with FLX-1510) e) C WG Clevis 2 3/16 " opening Choose a Tractor Shaft: a) WG CV Shaft, 540 rpm 1, b) WG CV Shaft, 1000 rpm 1, c) WG CV Shaft 1000 RPM 1 3/4" shaft 1, ) C Trailing Equal Angl Hitch c/w 540 Tractor Shaft 2, (Not Available with FLX-1510)

21 S CANADIAN MACHINE PRICES AND SPECIFICATIONS XH1500 Series 4 Rotary Cutter Subject to GST Effective July 2, 2016 ~ ~ Selection 3 ~ Choose a Blade Configuration ~ ~ Price CDN Wt/kgs 1) C Blade Pan Kit - cw Schulte Super Suction Updraft 4" Blades 1, ) C Blade Pan Kit - ccw Schulte Super Suction Updraft 4" Blades 1, ) C Blade Pan Kit - cw Basic Suction Updraft 4" Blades 1, ) C Blade Pan Kit - ccw Basic Suction Updraft 4" Blades 1, ) C Blade Pan Kit - Bush Blades Non Updraft 2, ) C Blade Pan Kit - cw Schulte Super Suction Updraft 5" Blades 2, ) C Blade Pan Kit - cw Schulte Super Suction Updraft 5" Blades 2, ~ ~ Selection 4 ~ Choose a Wing Axle Kit ~ ~ 1) C Single Axles for Wings (6 Tires required) 1, ) C Walking Axles for Wings (8 Tires Required) 2, ~ ~ Selection 5 ~ Choose a Tire Option ~ ~ Please state the quantity of tires that you would like to order as the numbers listed below are just single tires and not a tire kit. Price USA Wt/lbs PRICE PER TIRE 1) WG Solid Laminated Tire, 6 x 9 x ) WG Tire 24x Ply Severe Duty ) FWG Tire 24x Ply Severe Duty Foamed Filled ) WG Forklift Tire 6.5x10-10 Ply Rated ~ ~ Selection 6 ~ Choose a Destination Package ~ ~ Please select the destination of the cutter for proper Decals, Manuals, and Shielding 1) C308-NA North American/ Australia Destination Kits

22 S CANADIAN MACHINE PRICES AND SPECIFICATIONS XH1500 Series 4 Rotary Cutter Subject to GST Effective July 2, 2016 ~ ~ Selection 7 ~ Extra Options ~ ~ Price CDN Wt/kgs 1) C Manual Winch Kit ) C Towing Hitch Kit ) C Three Spool Valve Kit (For tractors with limited remote outlets) 1, ) C Double Acting Cylinder Kit "TEE" Connection ) C Hydraulic Hose Ends Kit (Pioneer Ends) ) C Independent Double Acting Cylinder Kit ) C Extra Long Hoses for Spool Valve Kit ) C Right Wing Gauge Wheel Kit ) C Left Wing Gauge Wheel Kit ) C Tool Box Kit ) C Flex Arm Mount ) C Tire Bumper Kit Assembly Charge Net Optional Factory PDI Net OPTIONAL PDI INCLUDES: greasing of all pivot points, gearbox oil checked, charge hydraulic cylinders and install pioneer ends. Tires will be installed where necessary. It is the dealers responsibility to remove shipping brackets & banding as well as to adjust mower height as specified in the operators manual. Please go to the Schulte website/dealer access for further information. IMPORTANT: When moving equipment on any type of road, if the rotary cutter obscures the tractor warning or tail lights, the cutter must be equipped with the S Safety Light Kit HYDRAULIC REQUIREMENTS FOR XH1500 A three circuit system provides independent lifting of each wing and height adjustment control, with float on two circuits. This system is preferred for optimum performance. If a three circuit system three spool valve kit is required - part #C PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

23 S CANADIAN MACHINE PRICES AND SPECIFICATIONS Eliminator Subject to GST Effective July 2, 2016 ELIMINATOR FEATURES - Chemical application spray kit for XH US Gallon (189 Litres) Capacity Tank - Adjustable Flow rate (can be matched to the product you are using) - Great for brush and weed control - Monitor for speed, pressure and application rates - Reduce drift while mowing- Spraying is done unbder the deck ` ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Price CDN 1) C Eliminator Spray Kit 11, Wt/kgs Factory Installation on XH IMPORTANT: OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown ObjectShield Information Message in the Rotary Cutter Spec Section in the sales price book.

24 CANADIAN MACHINE PRICES AND SPECIFICATIONS XH1000 Series 4 Rotary Cutter Subject to GST Effective July 2, 2016 CUTTER FEATURES - 7GA deck - Single domed, sweep clean deck - S safety chain kit 1/4" grade 70 - Two piece replaceable skid shoes - Rubber suspension - standard with 10,000 lbs capacity - Double safety chains front & rear - Four gearbox drive layout - 1/4" Round skid pans (Stump Jumpers) - Walking axles on center section 190hp down, 260hp splitter c/w 6 updraft blades - Hydraulic phasing lift system - Full floating front hitch - Pentagon blade bolt design - Hydraulic wing lift system - Inboard rotation - Operator's manual in holder Hubs and axles - Deck protection rings HOW TO ORDER: You must select from 1-6 to receive a complete rotary cutter including standard features. To receive additional options, choose from selection 7. ~ ~ Selection 1 ~ Choose a Basic Unit and Drive Package~ ~ Price CDN Wt/kgs 1) C Basic 10' Unit 20, ) S Safety Light Kit (Required) Choose a Drive Package: a) C CW Rotation on Center, 540 RPM, (Std. Rotation) 4, b) C CW Rotation on Center, 1000 RPM (Std. Rotation) 4, c) C CCW Rotation on Center, 540 RPM (Non Std. Rotation) 4, d) C CCW Rotation on Center, 1000 RPM (Non Std. Rotation) 4, ~ ~ Selection 2 ~ Choose a Hitch Type and Accessories ~ ~ 1) C Trailing Hitch CV Style 1, Choose a Clevis: a) CS01-106WG Open Clevis (Minimum Requirement) b) C WG Adjustable Clevis c) C WG Precision Hitch (Not Required with FLX1510) d) C WG Solid Tongue (Not Required with FLX1510) e) C WG Clevis with 2 3/16" Opening Choose a Tractor Shaft: a) WG CV Shaft, 540 RPM 1, b) WG CV Shaft, 1000 RPM 1, ) C Trailing Equal Angle Hitch c/w 540 Tractor Shaft 2, (Not Available with FLX1510) PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

25 CANADIAN MACHINE PRICES AND SPECIFICATIONS Subject to GST Effective July 2, 2016 XH1000 Series 4 Rotary Cutter ~ ~ Selection 3 ~ Choose a Blade Configuration ~ ~ Price CDN Wt/kgs 1) C Blade Pan kit - CW Schulte Super Suction Updraft 4" Blades 1, ) C Blade Pan kit - CCW Schulte Super Suction Updraft 4" Blades 1, ) C Blade Pan kit - CW Schulte Super Suction Updraft 5" Blades 1, ) C Blade Pan kit - CW Schulte Super Suction Updraft 5" Blades 1, ~ ~ Selection 4 ~ Choose a WIng Axle Kit ~ ~ 1) C Single Axle Kit for Right Wing ) C Wing Walking Axle Kit for Right Wing 1, ~ ~ Selection 5 ~ Choose a Tire Option ~ ~ Please state the quantity of tires that you would like to order as the numbers listed below are single tires and not tire kits. PRICE PER TIRE 1) WG Solid Laminated Tire, 6 x 9 x ) WG Tire 24x Ply Severe Duty ) FWG Tire 24x Ply Severe Duty Foam Filled ) WG Forklift Tire 6.5x10-10 Ply Rated ~ ~ Selection 6 ~ Choose a Destination Code ~ ~ C309-NA North American/ Australia Destination Kits ~ ~ Selection 7 ~ Extra Options ~ ~ 1) C Manual Winch ) C Towing Hitch Kit ) C Three Spool Valve Kit 1, ) C Right Wing Guage Wheel Kit ) C Tool Box Kit ) C Flex Arm Kit ) C Front Belting ) C Pioneer Ends PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

26 S CANADIAN MACHINE PRICES AND SPECIFICATIONS Subject to GST Effective July 2, 2016 XH1000 Series 4 Rotary Cutter IMPORTANT: Safety Tow Chain Kit must be used at all times when moving equipment on any type of road. IMPORTANT: When moving equipment on any type of road, if the rotary cutter obscures the tractor warning or tail lights, the cutter must be equipped with the S Safety Light Kit Assembly Charge Net Optional Factory PDI Net OPTIONAL PDI INCLUDES: greasing of all pivot points, gearbox oil checked, charge hydraulic cylinders and install pioneer ends. Tires will be installed where necessary. It is the dealers responsibility to remove shipping brackets & banding as well as to adjust mower height as specified in the operators manual. Please go to the Schulte website/dealer access for further information. PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

27 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-1800 ROTARY CUTTER CUTTER FEATURES - 540/1000 RPM Drive - 80 Degree CV Drive - 7 ga. Spun Formed Stump Jumpers - Height Control Cylinder & Hoses -Replaceable Skid Shoes -Wing Lift Cylinders & Hoses - 7 ga Single Domed Deck - S Safety Chain (1/4" gr lbs cap.) - Deck Protection Rings - Operator's and Parts Manual Holder - Weasler Drive Lines with Self Adjusting Clutches - Over Center Folding Wings - Cutting Width 180" (4.57m) - Transport Width (max with duals on wings) 102"(2.59m more specs on brochure ~ ~ Selection 1 ~ Choose a Basic Unit, Drive Package ~ ~ Price CDN WT(kgs) C Schulte FX-1800, Basic Unit 11, ,550 S Safety Light Kit (Required) Choose a Drive Package: a) C Drive Package, CW Center, 540 RPM 6, in base b) C Drive Package, CW Center, 1000 RPM 6, in base ~ ~ Selection 2 ~ Choose a Hitch Option ~ ~ C Trailing Hitch, CV Style Choose a CV Shaft: a) WG CV Shaft, 540 RPM 1, b) WG CV Shaft, 1000 RPM 1, c) WG CV Shaft 1000 RPM 1 3/4" shaft 1, C Equal Angle Hitch Kit w/ 540 RPM Shaft 2, ~ ~ Selection 3 ~ Choose a Clevis ~ ~ CS01-106WG Open Clevis (Minimum Requirments) C WG Adjustable Clevis (not required with FLX10 or FLX15) C WG Precision hitch C WG Solid Tongue ~ ~ Selection 4 ~ Choose a Center and The WIng Axle Kit ~ ~ C Duals Wheel Standard on Center OR 1, C Walking Tandems on center (6 Tires minimum) 2, C Single Axle Kit for Left and Right Wings (required) Prices NOTE: and specifications (accomodates subject to 1 or change 2 tires) without notice or obligation. PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

28 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-1800 ROTARY CUTTER ~ ~ Selection 5 ~ Choose a Safety Guard ~ ~ C Chain Guards Single Front and Rear C Chain Guards Double Front and Rear 1, ~ ~ Selection 6 ~ Choose a Pan Kit ~ ~ C Pan Kit (required) 1, ~ ~ Selection 7 ~ Choose a Blade Configuration ~ ~ C Blades, CW Center C Shredder Blades, CW Center ~ ~ Selection 8 ~ Choose a Axle Kit ~ ~ C Axle Kit for 4 Tires C Axle Kit for 6 Tires C Axle Kit for 8 Tires 1, ~ ~ Selection 9 ~ Choose a Tire Option ~ ~ Please state the quantity of tires that you would like to order as the numbers listed below are single tires and not tire kits WG Solid Laminated Tires, 6 x 9 x WG Forklift Tire 6.5 x ply on 2 pce 5 bolt rim WG Tire 24x Ply Severe Duty FWG Tire 24x Ply Severe Duty Foam Filled ~ ~ Selection 10 ~ Choose a Destination Code ~ ~ C185-NA North American & Australian Decal Kit PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

29 Subject to GST CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX1800 ROTARY CUTTER ~ ~ Selection 11 ~ Choose Extra Options ~ ~ S Safety Light Kit C Strut Mount for Flex Arm,(Factory Installed) C Strut Mount for Flex Arm, (parts only) C Tension Link Leveling Rod, Factory Installed C Tension Link Leveling Rod, Weld on Parts only C Hose Kit, independent wing-lift Assembly Charge on Pan Units PDI PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER IMPORTANT: 1) Safety Chain Kit must be used at all times when moving equipment on any type of road. 2) OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown Object Shield Message in the Rotary Cutter Spec section in sales price book.

30 CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-1200 ROTARY CUTTER CUTTER FEATURES - 540/1000 RPM Drive - 80 Degree CV Drive - 7 ga. Spun Formed Stump Jumpers - Height Control Cylinder & Hoses -Replaceable Skid Shoes -Wing Lift Cylinders & Hoses - 7 ga Single Domed Deck - S Safety Chain (1/4" gr lbs cap.) - Deck Protection Rings - Operator's and Parts Manual Holder - Weasler Drive Lines with Self Adjusting Clutches - Over Center Folding Wings - Cutting Width 126" (3.20m) - Transport Width (max with duals on wings)97.5"(2.47m) more specs on brochure ~ ~ Selection 1 ~ Choose a Basic Unit, Drive Package ~ ~ Price CDN WT(lbs) C FX1200, Basic Unit 11, ,206 S Safety Light Kit (Required) DRIVE PACKAGE (choose one) C CW Rotation on Center, 540 RPM 4, in base C CW Rotation on Center, 1000 RPM 4, in base ~ ~ Selection 2 ~ Choose a Hitch Option ~ ~ C Trailing Hitch, CV Style Choose a CV Shaft: a) WG CV Shaft, 540 RPM 1, b) WG CV Shaft, 1000 RPM 1, C Equal Angle Hitch Kit w/ 540 RPM Shaft 2, ~ ~ Selection 3 ~ Choose a Clevis ~ ~ CS01-106WG Open Clevis (Minimum Requirments) C WG Adjustable Clevis C WG Precision hitch C WG Solid Tongue ~ ~ Selection 4 ~ Choose a WIng Axle Kit ~ ~ C Single Axle Kit for Left and Right Wings (required) (accomodates 1 or 2 tires) C Duals Wheel Standard on Center OR 1, C Walking Tandems on center (6 Tires minimum) 2, PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

31 CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-1200 ROTARY CUTTER ~ ~ Selection 5 ~ Choose a Safety Guard ~ ~ Price CDN WT(lbs) C Chain Guards Single Front & Rear C Chain Guards Double Front & Rear ~ ~ Selection 6 ~ Choose The Pan Kit ~ ~ C Pan Kit (required) 1, ~ ~ Selection 7 ~ Choose a Blade Configuration ~ ~ C Updraft Blades, CW Center C Shredder Blades, CW Center ~ ~ Selection 8 ~ Choose a Axle Kit ~ ~ C Axle Kit for 3 Tires C Axle Kit for 5 Tires C Axle Kit for 6 Tires ~ ~ Selection 9 ~ Choose a Tire Option ~ ~ Please state the quantity of tires that you would like to order as the numbers listed below are single tires and not tire kits WG Solid Laminated Tires, 6 x 9 x WG Tire Assy, Forklift, 6.5 x ply on 2 pce 5 bolt rim WG Tire 24x Ply Severe Duty FWG Tire 24x Ply Severe Duty Foam Filled ~ ~ Selection 10 ~ Choose a Destination Code ~ ~ C195-NA North American & Australian Decal Kit PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

32 CANADIAN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 FX-1200 ROTARY CUTTER ~ ~ Selection 11 ~ Choose a Extra Options ~ ~ S Safety Light Kit C Strut Mount for Flex Arm,(Factory Installed) C Strut Mount for Flex Arm, (parts only) C Tension Link Leveling Rod, Factory Installed C Tension Link Leveling Rod, Weld on Parts only Assembly Charge NET Optional Factory PDI NET IMPORTANT: 2) PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown Object Shield Message in the Rotary Cutter Spec section in sales price book.

33 S CANADIAN MACHINE PRICES AND SPECIFICATIONS Subject to GST Effective July 2, 2016 V1280 Rotary Cutter CUTTER FEATURES RPM Drive line - 80 degree CV joint to tractor - Spring steel bushings - Round skid pans L x 15 tires, center section - Rear counterbalance springs - Replaceable skid shoes - Aircraft tires on wings - S safety chain kit 1/4" grade GA Deck - Height control cylinder with hoses with 10,000 lbs capacity - Heavy duty slip clutches - Wing lift cylinder with hoses - Operator's manual in holder - Deck protection rings - Laminated rubber shielding - Rear Mounted Center Rotor HOW TO ORDER: You must select from 1 and 2 to receive a complete rotary cutter including standard features. To receive additional options, choose from selection 3. ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Price CDN Wt/kgs 1) CS Basic 12' Unit, 540 RPM 34, ,750 ~ ~ Selection 2 ~ Choose a Hitch Type ~ ~ 1) CS01-106WG Open Clevis ) C WG Precision hitch ~ ~ Selection 3 ~ Extra Option ~ ~ 1) S Safety Light Kit IMPORTANT: Safety Chain Kit must be used at all times when moving equipment on any type of road. or tail lights, the cutter must be equipped with the S Safety Light Kit IMPORTANT: OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown ObjectShield Information Message in the Rotary Cutter Spec Section in the sales price book. PREDELIVERY SERVICE IS REQUIRED BY DEALER OR END USER

34 S CANADIAN MACHINE PRICES AND SPECIFICATIONS FLX-1510 FLEX ARM Effective July 2, New heavy duty 11l x 15, 2 ply tires, load cap. Of 4000 lbs - Opt. 6 port selector valve kit for independent - Cut dirctly in-line with the tractor or at any offset distance upto 122" wing action or limited tractor hydraulic outlets lb capacity, 6 bolt hubs - Continuous power rating 1000rpm - Spring steel bushings, induction harden pins at major pivot points - Bolt in replacement axles - Minimum of 3 hydraulic circuits required to operate with 15' or 10' mow- Safety light kit - Heavy duty 3-1/2 x 36 welded hydraulic cylinder - Operator's manual in holder HOW TO ORDER: Selection 1 will g` To receive additional options, choose from selection 2. FLEX ARM FEATURES ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Price CDN Wt/kgs 1) A FLX 1510 Flexarm 25, ,850 ~ ~ Selection 2 ~ Extra Options ~ ~ 1) A Six Port Selector Valve Kit for Independent Wing 1, Actions with Limited Tractor Hydraulics (Fits FLX-1510) 2) A Hose kit for independent wing lift- Tractors with 4 valve banks When choosing this opt. you will require a C (Independent Double Acting Cylinder Kit) * C Independent Double Acting Cylinder Kit Assembly $ Factory PDI $ IMPORTANT: OSHA, ASAE, SAE, and ANSI standards REQUIRE the use of Chain Guards, Deflectors, or Solid Skirts/Bands at all times. Schulte recommends mower be equipped with deflectors or double chain guards for all mowing purposes. Single chain guards may be used for agricultural purposes only and are specifically not recommended for highway, right-of-way, parks or greenbelt mowing. Before ordering a mower, read the Thrown ObjectShield Information Message in the Rotary Cutter Spec Section in the sales price book.

35 CDN MACHINE PRICES AND SPECIFICATIONS FX-209 Rotary Cutter Effective July 2, Push or pull capability - Gearbox Rating 210 hp - 9ft / 3m overall width - Two rotor base unit common to all configuration - Cutting Height: 2" - 13" (5.1 cm - 33 cm) - Pans with Schulte Super Suction Blades - Cutting Width: " (2.78 m) - Double Chain Front & Rear - Cutting Capacity: 3" (7.6 cm) - 7 Ga Deck - Minimum Tractor HP 50 HP ( 37.3 kw) and 1000 RPM drive options - Cat. II & III 3 Point / Semi Mount Swing (13 left or right swing), Trailing Pull Price CDN C FX-209 Base Unit 8, Choose One Mount CUTTER FEATURES - ALL HITCH TYPES ~ ~ Selection 1 ~ Choose a FX-209 Base Unit ~ ~ ~ ~ Selection 2 ~ Choose a FX-209 Non Trailing Configuration ~ ~ C PT Mount Option or 1, C Semi Mount Swing or 3, C Semi Mount 1, Choose One Drive Package C RPM Drive Package NON-TRAILING or 2, C RPM Drive Package NON-TRAILING 1, C Front Frame Pushing 540 RPM Drive (only to be used with 2, FM-115 or FM Front mount 3pt frame Not needed with Tractor front 3pt system) Choose One Wheel Assembly C FX-209 Wheel Assembly Non-Trailing Standard or 1, C FX-209 Wheel Assembly Non-Trailing Hydraulic 2, ~ ~ Selection 3 ~ Choose a FX-209 Trailing Hitch Configuration ~ ~ C FX-209 Trailing Hitch 3, CS01-106WG Open Clevis (Minimum Requirement) or C wg Adjustable Clevis or C WG Precision Hitch or C WG Solid Tongue Choose One Drive Package C RPM Drive Package Trailing or 3, C RPM Drive Package Trailing 3, Wt/kgs

36 CDN Effective July 2, 2016 FX-209 Rotary Cutter ~ ~ Selection 4 ~ Choose Options ~ ~ Price CDN C BLADE PAN OPTION (Must Pick) 1, C HALF LENGTH BELTING OPTION (Front and Back) Wt/kgs ~ ~ Selection 5 ~ Choose Tire Options ~ ~ (CHOOSE 2 TIRES PER UNIT) WG Solid Laminated Tires, 6 x 9 x WG Tire 24x Ply Severe Duty FWG Tire 24x Ply Severe Duty Foam Filled WG Forklift New, 6.5 x ply rated on 2 pcs 5 bolt rim

37 CDN MACHINE PRICES AND SPECIFICATIONS FX-107 Rotary Cutter Effective July 2, 2016 CUTTER FEATURES - ALL HITCH TYPES - Rigid single domed 7 gauge deck construction - Pull type and 3 point hitching options - Overall width: 95.5" ( 2.43 m) - Base unit common to all configurations - Cutting Height: 3" /8" (7.6 cm - 33 cm) RPM drive - Cutting Width: 84" (2.13 m) - Double Chain Front & Rear - Cutting Capacity: 3" (7.6 cm) - 7 Ga Deck - Minimum Tractor HP 50 HP ( 37.3 kw) - Pull type unit has the ability to accept open - Cat. II & III 3 Point / Trailing Pull clevis, solid tongue, adjustable clevis ~ ~ Selection 1 ~ Choose a Base Unit ~ ~ Price CDN C FX-107 Base Unit 5, ~ ~ Selection 2 ~ Choose a 3 Point Option Configuration ~ ~ C PT Mount Option (if this choosen skip Trailing Hitch Option) 2, ~ ~ Selection 3 ~ Choose a Trailing Hitch Configuration ~ ~ C Trailing Hitch 4, CS01-106WG Open Clevis (Minimum Requirement) or C wg Adjustable Clevis or C WG Precision Hitch or C WG Solid Tongue ~ ~ Selection 4 ~ Blade Pan Option ~ ~ C BLADE PAN OPTION (Must Pick) Wt/kgs ~ ~ Selection 5 ~ Choose Tire Options ~ ~ WG (CHOOSE 2 TIRES PER UNIT) Solid Laminated Tires, 6 x 9 x WG Tire 24x Ply Severe Duty FWG Tire 24x Ply Severe Duty Foam Filled WG Forklift New, 6.5 x ply rated on 2 pcs 5 bolt rim

38 CDN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 RDX-117 SNOW BLOWER RDX-117 Snow Blower Specs: Cutting Width: 117" Tractor HP: HP Cutting Height: 45.5" Lower Auger Diameter: 23" Upper Auger Diameter: 14" Adjustable, replacable skid shoes Replaceable Cutting Blade Gear Driven Rotator High molecular plastic chute rotating surface Double chute deflector on HD and Truck loading chutes Fan Diameter: 38" Capacity - Dry Snow / Wet Snow Fan Type: 5 Paddle 762 tons per hr / 2394 per hr Drive: 1000 RPM ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Retail Price Weight (kg) B RDX-117 (117" Snow Blower) 18, WG Standard Gearbox (tractors with cw pto rotation) 3, R Non-standard Gearbox (tractors with ccw pto rotation) 4, WG 1-3/4 Z20 (size 9) for SDX-117 / RDX WG 1-3/8 Z21 (size 9) for SDX-117 / RDX NOTE : Do not order above shaft if going on a Front Mount Instead, order from FM350 price sheet ~ ~ Selection 2 ~ Choose a Gear Box ~ ~ ~ ~ Selection 3 ~ Choose a Power Shaft ~ ~ 1. Factory Assembly Charge: $50 2. Predelivery service is $50.00 or required to be carried out by the Dealer or end user. 3. Prices are subject to change without notice or obligation.

39 CDN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 RDX-117 SNOW BLOWER ~ ~ Selection 4 ~ Choose a Chute kit ~ ~ Retail Price Weight (kg) B Heavy Duty Chute Kit with Dbl Chute Deflector 1, B Cylinder Kit for B (Required) B Truck Loading Chute Kit with Dbl Chute Deflector 1, B Cylinder Kit for B (Required) NOTE: Cylinder kits are complete with 2" x 6" cylinder & hoses B WG Gauge Wheels with Tapered Roller Bearings 1, Factory Assembly Charge: $50 2. Predelivery service is $50.00 or required to be carried out by the Dealer or end user. 3. Prices are subject to change without notice or obligation.

40 CDN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 SDX-117 SNOW BLOWER SDX-117 Snow Blower Specs: Cutting Width: 117" Tractor HP: HP Cutting Height: 45.5" Lower Auger Diameter: 23" Upper Auger Diameter: 14" Adjustable, replacable skid shoes Replaceable Cutting Blade Gear Driven Rotator High molecular plastic chute rotating surface Double chute deflector on HD and Truck loading chutes Fan Diameter: 38" Capacity - Dry Snow / Wet Snow Fan Type: 5 Paddle 762 tons per hr / 2394 per hr Drive: 1000 RPM ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Retail Price Weight (kg) B SDX-117 (117" Snow Blower) 13, WG Standard Gearbox (tractors with cw pto rotation) 3, R Non-standard Gearbox (tractors with ccw pto rotation) 4, WG 1-3/4 Z20 (size 9) for SDX-117 / RDX WG 1-3/8 Z21 (size 9) for SDX-117 / RDX NOTE : Do not order above shaft if going on a Front Mount Instead, order from FM350 price sheet ~ ~ Selection 2 ~ Choose a Gear Box ~ ~ ~ ~ Selection 3 ~ Choose a Power Shaft ~ ~ 1. Factory Assembly Charge: $50 2. Predelivery service is $50.00 or required to be carried out by the Dealer or end user. 3. Prices are subject to change without notice or obligation.

41 CDN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 SDX-117 SNOW BLOWER ~ ~ Selection 4 ~ Choose a Chute kit ~ ~ Retail Price Weight (kg) B Heavy Duty Chute Kit with Dbl Chute Deflector 1, B Cylinder Kit for B (Required) B Truck Loading Chute Kit with Dbl Chute Deflector 1, B Cylinder Kit for B (Required) NOTE: Cylinder kits are complete with 2" x 6" cylinder & hoses B WG Gauge Wheels with Tapered Roller Bearings 1, Factory Assembly Charge: $50 2. Predelivery service is $50.00 or required to be carried out by the Dealer or end user. 3. Prices are subject to change without notice or obligation.

42 CDN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 RDX-102 SNOW BLOWER RDX-102 Snow Blower Specs: Cutting Width: 102" Tractor HP: HP ( kw) Cutting Height: 37" Overall Height: 100" Auger Diameter: 23" Adjustable, replacable skid shoes Replaceable Cutting Blade Gear Driven Rotator High molecular plastic chute rotating surface Double chute deflector on HD and Truck loading chutes Fan Diameter: 30" Capacity - Dry Snow / Wet Snow Fan Type: 4 Paddle 426 tons per hr / 1343 per hr PTO Speed; 540 or 1000 RPM ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Retail Price Weight (kg) B RDX-102 (102" Rotating Drum Snow Blower) 12, WG Size 9 Heavy Duty PTO Shaft 540 RPM WG Size 9 Heavy Duty PTO Shaft (for TV-145 Engine End) 540 RPM Optional Gear Gbox B RPM Gear Box STANDARD 1, B R 1000 RPM Gear Box CCW 2, Power Shaft for 1000 RPM Gear Box WG 1-3/8 21 Spline sahft 1000 RPM NOTE : Do not order above shaft if going on a Front Mount Instead, order from FM350 price sheet ~ ~ Selection 2 ~ Choose a Power Shaft ~ ~ ~ ~ Selection 3 ~ Choose a Chute Kit ~ ~ B Heavy Duty Chute Kit with Dbl Chute Deflector 1, B Cylinder Kit for B (Required) B Truck Loading Chute Kit with Dbl Chute Deflector 1, B Cylinder Kit for B (Required) NOTE: Cylinder kits are complete with 2" x 6" cylinder & hoses 1. Factory Assembly Charge: $50 2. Predelivery service is $50.00 or required to be carried out by the Dealer or end user. 3. Prices are subject to change without notice or obligation. B WG Gauge Wheels with Tapered Roller Bearings 1,

43 CDN MACHINE PRICES AND SPECIFICATIONS Effective July 2, 2016 SDX-102 SNOW BLOWER SDX-102 Snow Blower Specs: Cutting Width: 102" Adjustable, replacable skid shoes Drive: 540 or 1000 RPM Replaceable Cutting Blade Cutting Height: 35" Gear Driven Rotator Overall Height: 96" Hydraulic Chute Rotation Auger Diameter: 23" Capacity Dry Snow/Wet Snow Fan Diameter: 30" 388 Tons per hr / 1222 tons per hr Fan Type: 4 Paddle Tractor HP: HP ( kw) ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Retail Price Weight (kgs) B SDX102 Standard Drum Snow Blower 8, ~ ~ Selection 2 ~ Choose a Power Shaft ~ ~ WG Size 9 Heavy Duty PTO Shaft 540 RPM WG Size 9 Heavy Duty PTO Shaft (for TV-145 Engine End) 540 RPM Optional Gear Gbox B RPM Gear Box STANDARD 1, B R 1000 RPM Gear Box CCW 2, Power Shaft for 1000 RPM Gear Box WG 1-3/8 21 Spline sahft 1000 RPM NOTE : Do not order above shaft if going on a Front Mount Instead, order from FM350 price sheet ~ ~ Selection 3 ~ Choose a Chute Kit ~ ~ B Heavy Duty Chute Kit with Dbl Chute Deflector 1, B Cylinder Kit for B (Required) B Truck Loading Chute Kit with Dbl Chute Deflector 1, B Cylinder Kit for B (Required) NOTE: Cylinder kits are complete with 2" x 6" cylinder & hoses 1. Factory Assembly Charge: $50 2. Predelivery service is $50.00 or required to be carried out by the Dealer or end user. 3. Prices are subject to change without notice or obligation.

44 Effective July 2, 2016 CDN MACHINE PRICES AND SPECIFICATIONS SDX-102 SNOW BLOWER ~ ~ Selection 4 ~ Choose a Extra Options ~ ~ Weight (kgs) 27 Retail Price 23 B pt Extension Kit - no shaft incl B WG Gauge Wheels with Tapered Roller Bearings 1, Factory Assembly Charge: $50 2. Predelivery service is $50.00 or required to be carried out by the Dealer or end user. 3. Prices are subject to change without notice or obligation.

45 CDN MACHINE PRICES AND SPECIFICATIONS SDX-840 SNOW BLOWER Effective July 2, 2016 Cutting Width: 84" Tractor HP: HP Adjustable, replacable skid shoes Cutting Height: 30" Replaceable Cutting Blade Overall Height: 78" Gear Driven Rotator Auger Diameter: 18" Hydraulic Chute Rotation Fan Diameter: 26" Capacity Dry Snow/Wet Snow Fan Type: 4 Paddle 258 Tons per hr / 810 tons per hr Drive: 540 RPM ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ Retail Price Weight (kgs) B SDX-840 Snow Blower with Chute 8, ~ ~ Selection 2 ~ Choose a Power Shaft ~ ~ WG Heavy Duty PTO Shaft (Size 9) ~ ~ Selection 3 ~ Choose a Extra Options ~ ~ B Hyd Cylinder Kit for Chute Deflector (2"x6" cyl & hoses) B Point Extension Kit ( No Shaft Included) B WG Gauge Wheels with Tapered Roller Bearings 1, B Manual Chute Bar for Chute Deflector ` 1. Factory Assembly Charge: $50 2. Predelivery service is $50.00 or required to be carried out by the Dealer or end user. 3. Prices are subject to change without notice or obligation.

46 CDN MACHINE PRICES and SPECIFICATIONS Effective July 2, 2016 FM-350 Front Mount 3pt Hitch Frame FM-350 Specs: Tractor HP: 85 HP HP Tractor PTO rpm for SDX-117 and SDX-102 Adjustment: Accommodates tractors between 151" and 540 rpm for SDX-102 only 211" measured from mount plate to drawbar pin Lift Capacity : 5000 lbs Nominal Ground Clearance - 13" depending on tractor installation Nominal Lift Range - 18" Weight lbs ~ ~ Selection 1 ~ Choose a Basic Unit ~ ~ RETAIL PRICE WEIGHT (kgs) F FM-350 Front Mount Frame (NO Driveline Package) 6, Used for SV 3pt V-BLADE (must choose for all attactments) Includes 2 hydraulic banks for operation F Driveline package (Used for Snow Blowers) 3, ~ ~ Selection 2 ~ Choose Gear Box ~ ~ F :1 Rear Gear Box 2, Select when connecting a 1000 RPM PTO tractor to a SDX-117 or RDX-117 or when connecting a 540 RPM PTO tractor to a SDX-102 or RDX-102 snow blower F to 540 RPM Rear Reduction Gearbox 2, Select when connecting a 1000 RPM PTO tractor to a SDX-102 or RDX-102 ~ ~ Selection 3 ~ Choose REAR TRACTOR SHAFT ~ ~ NOTE: Power delivered from a 1,000 RPM tractor only WG 1-3/8 Z21 for SDX-102 / RDX WG 1-3/4 Z20 for SDX-102 / RDX WG 1-3/8 Z21 (Size 9) for SDX-117 / RDX WG 1-3/4 Z20 (size 9) for SDX-117 / RDX NOTE: Power delivered from a 540 RPM tractor only WG 1-3/8 Z6 for SDX-102 / RDX Factory Assembly Charge: Call for Price 2. Prices are subject to change without notice or obligation.

47 ver MM MASTER PRICE SHEET CDN MACHINE PRICES and SPECIFICATIONS Effective July 2, 2016 FM-350 Front Mount 3pt Hitch Frame ~ ~ Selection 4 ~ Choose Hydraulic Bank~ ~ RETAIL PRICE WEIGHT (kgs) F Hydraulic Bank and Mount, Single Required for drum rotation on RDX-102 / RDX-117 Tractor Mount ~ ~ Selection 5 ~ Choose Options ~ ~ *Please contact us for tractor mount options & availability Factory Assembly Charge: Call for Price 2. Prices are subject to change without notice or obligation.