W/ MAGNETIC TAPE ON FACE CENTER W/ MAGNETIC TAPE ON FACE CENTER W/ STEEL TAPE ON FACE BOTTOM L3-1 W/ STEEL TAPE ON FACE BOTTOM

Size: px

Start display at page:

Download "W/ MAGNETIC TAPE ON FACE CENTER W/ MAGNETIC TAPE ON FACE CENTER W/ STEEL TAPE ON FACE BOTTOM L3-1 W/ STEEL TAPE ON FACE BOTTOM"

Winfred Simpson
5 years ago
Views:

2 6 4 WITH CE 4 HALF UPRIGHT -1 1 & 5mm Hex key Tool Place vertical extrusion and lock horizontal extrusions by using 5mm hex key tool. W/ MAGNETIC TAPE W/ MAGNETIC TAPE / -2 /-1 HALF UPRIGHT Place horizontal extrusion and lock it by using 5mm hex key tool. 5mm Hex key Tool -1 W/ MAGNETIC TAPE W/ MAGNETIC TAPE POST FOOT DETAIL GRAPHIC BAR POST FOOT Make sure to place with the POST FOOT facing DOWN 1

3 8 CORNER LOCK 4 CORNER LOCK CORNER LOCK DETAIL CORNER LOCK CORNER LOCK / -2 /-1 Slide CORNER LOCK into front channel. CORNER LOCK DETAIL CORNER LOCK SET SCREW CORNER LOCK Slide the the tracks of one extrusion. Then push the two extrusions together. 2

4 GRAPHIC MOUNTING BAR / GRAPHIC MOUNTING BAR TOP HALF UPRIGHT HALF UPRIGHT Code # Description 4 TOP HALF UPRIGHT GRAPHICS MOUNTING BAR CPH C 4 CAP FOR GRAPHIC BA -1 1 STEEL TAPE Place GRAPHIC MOUNTING BAR into channel. Make sure steel tape in facing to the front. GRAPHIC MOUNTING BAR DETAIL Place Graphic Mounting Bar into extrusion channel. TOP & 5mm Hex key Tool STEEL TAPE GRAPHIC MOUNTING BAR Place vertical extrusion and lock horizontal extrusions by using 5mm hex key tool. -1 Place onto top of vertical graphic bar DETAIL Slide the the tracks of one extrusion. Then push the two extrusions together. SET SCREW W/MAGNETIC TAPE -1 W/MAGNETIC TAPE -1-1 W/MAGNETIC TAPE -1 W/MAGNETIC TAPE -1 / -2 /-1 After the extrusions are pushed together tighten all four set screws on both sides to secure the and extrusions into place. 3

5 GRAPHICS WITH HOOK ON TOP HOOK HOOK PLACE GRAPHICS WITH THE HOOKS FOR BETTER ALIGMENT L5-1 Code # Description L5-2 1 GRAPHICS L5-1 1 GRAPHICS L5-3 1 GRAPHICS ll5-4 1 GRAPHICS L5-6 1 GRAPHICS L5-7 1 GRAPHICS L5-5 1 GRAPHICS L5-2 L5-3 ll5-4 L5-5 L5-6 L5-7 / -2 /-1 HOOK 4

LV3 LIGHT 4 GREY SKINNY LIGHT WITH OSRAM TITAN 50W

channel at an angle and then gently lower down.

6 LV3 LIGHT 4 GREY SKINNY LIGHT WITH OSRAM TITAN 50W LAM LV3 LIGHT LV3 LIGHT / -2 /-1 LV3 LIGHT LIGHT DETAIL LV3 LIGHT LIGHT CLIP 0 LIGHT LV1 LIGHT LV3 LIGHT LIGHT CLIP Slide the light clip into the channel at an angle and then gently lower down. Then slide the LV3 Light onto the light clip. 0 Light LV1 Light LV3 5

CKAP Code # Description CKAPS 20 STANDOFFS 1-1 1 GRAPHIC 1-7 1 GRAPHIC 1-2 1 GRAPHIC 1-8 1 GRAPHIC 1-4 2 GRAPHIC 1-3 2 GRAPHIC 1-7 1-6 CKAPS Detail 1-8 1-5 / -2 /-1 1-3 1-4 1-3 SCREW TO TURN HEAD

7 CKAP Code # Description CKAPS 20 STANDOFFS GRAPHIC GRAPHIC GRAPHIC GRAPHIC GRAPHIC GRAPHIC CKAPS Detail / -2 / SCREW TO TURN HEAD SCREW FOR SINTRA/ GRAPHICS Screw the CKAP, clockwise, into the channel until it is tight. Loosen the head screw and make sure the slit in the head is running the correct direction, then tighten back into place. Loosen the SINTRA / GRAPHIC screw and insert the substrate and tighten into place CKAPS CKAP 1-1 SINTRA GRAPHIC 2.5 MM HEX KEY Place SINTRA/ GRAPHIC into CKAP channel. Then gently tighten by using 2.5 mm Hex key 6

8 2 4 SHORT CANOPY CONNECTOR CANOPY SCREW 4 CANOPY SCREW CANOPY WASHER 4 CANOPY WASHER ARCH CANOPY 2 ARCH CANOPY Frame Assembly Assemble frame as shown 3 1 CANOPY SCREW ARCH CANOPY PART LIST: PER UNIT 7 30MM DIA. TUBE SECTIONS Step 1 Assemble frame in numerical order as shown on right. Numbers will be on the backside of the tube. Step 2. Stretch fabric over frame. - When working with fabric use gloves or clean hands and keep fabric away from dirty surfaces. 2 2 CANOPY SCREW / -2 /-1 7 Pull fabric over frame and secure with zipper.. ARCH CANOPY ARCH CANOPY CANOPY SCREW ZIPPER CANOPY WASHER INSTAL COVER DO NOT ZIP ZIP COVER STEP # 3 STEP # 2 FIRST INTALL COVER [ DO NO ZIP]. THEN ASSEMBLE LONG / SHORT CANOPY CONNECTOR STEP #1 7

9 3 2 TABLE TOP V-LEG 4 2 V-LEG TABLE 5 2 V-LEG GRAPHIC #1 4 / -2 /-1 #2 #3 3 TABLE TOP DETAIL 5 TABLE LEG TOOL HEX 4MM TABLE TOP DETAIL TABLE TOP TABLE TOP UPRIGHT Turn Over TABLE TOP and gently tighten TABLE LEG in place. TOOL CORNER LOCK Attach TABLE TOP to bottom upright extrusion by locking CORNER LOCK. 8

10 2 6 2 TABLE TOP V-LEG 4 2 V-LEG TABLE #1 4 #2 #3 / -2 /-1 6 TABLE TOP DETAIL TABLE LEG TOOL HEX 4MM TABLE TOP DETAIL TABLE TOP TABLE TOP UPRIGHT Turn Over TABLE TOP and gently tighten TABLE LEG in place. TOOL CORNER LOCK Attach TABLE TOP to bottom upright extrusion by locking CORNER LOCK. 9

TensionLite Plus 10 ft. Wave Shape Mural Wall Design 2

TensionLite Plus 10 ft. Wave Shape Mural Wall Design 2 TensionLite is a collection of sophisticated, ergonomically designed exhibit booths. Formulate combines state-of-the-art zipper pillowcase dye-sublimated