Cafe Buffet Fiberglass Reflections

Transcription

1 B Cafe Buffet Fiberglass Reflections In This Section Hot Food Unit B Hot Top B Hot/Cold Combo Unit B Cold Food Unit Ice or Mechanically Refrigerated B Frost Top Mechanically Refrigerated B Cool Breeze Unit Listed NSF/ANSI Standard 7 B Solid Top Unit B Beverage Counter B Cashier Stand B Corner Unit B-11-B...74 Tray Stand B Beverage Cooler B Bloomington Cold Extra Deep Cold Pan - Listed NSF/ANSI Standard 7 B

2 Hot Food Unit R4-HF Operator s side shown with optional RBPG protector guard and open under storage with hinged doors JOB ITEM # QTY # MODEL NUMBER R2-HF R3-HF R4-HF R5-HF R6-HF FEATURING WORKS IN A DRAWER. QUICKLY REPLACE & REPAIR HEATING ELEMENTS. The versatile modular design of the Reflections Hot Food units allows you to customize either a cafeteria or a buffet unit to fit your line-up. These hot food serving units will hold pans up to 6 in depth. Reflections units are compatible and will interlock with other Reflections units. Only Piper's equipment has the advantage of technology and certification. This ensures that your food is kept "out of the DANGER-ZONE." Food spoilage occurs mainly because of rapidly accelerated bacteriological activity within the 40F-140F "DANGER-ZONE." With hot food stays above 140 F longer and cold food is kept below 40 F. Both are key factors in HACCP compliance and the fight against foodborne pathogens. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base 20-gauge stainless steel bottom-mounted wet/dry food wells with 12 x 20 die-stamped opening and 1/4 raised beaded edge top centered 2 insulation on sides and between wells, 1-1/2 on bottom, 1 on the ends and 1/4 fiber frax all around 208VAC/1000W or 240VAC/1330W heating element per well wired to a thermostat mounted to the control panel Wells can be run wet or dry Works-in-a-drawer allows element access without removal of unit top 4 diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units Drain option comes with 3/4" FPT ball valve under unit DIMENSIONS R2-HF - 36 H x 30 D x 36 L R3-HF - 36 H x 30 D x 50 L R4-HF - 36 H x 30 D x 60 L R5-HF - 36 H x 30 D x 74 L R6-HF - 36 H x 30 D x 96 L ELECTRICAL All units available in 208 or 240 volt, single-phase standard Seven foot electrical cord and plug STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides Protector guards Under storage, hinged doors Common drains and manifolds See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-1 52

3 Hot Food Unit 36" Model# # of Wells B-1 (A) Length 208V Wattage 240V Wattage RSCB 8 stainless steel cutting board RMCB 8 maple cutting board RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RSES End shelf - drop type RBHL Heat lamps, bullet-type (buffet only) RCPG Cafeteria style protector guard RCPGC Classic tubular glass cafeteria guard RCPGL Cafeteria style protector guard with incandescent RCPGFL Cafeteria style protector guard with fluorescent RCPGHL Cafeteria style protector guard with heat and light strips RCPGH Cafeteria style protector guard with heat strips RCDD Two tier cafeteria protector guard RCDDC Classic two tier tubular glass cafeteria guard RCDDL Two tier cafeteria protector guard with fluorescent RCEG Cafeteria end guards (pr) ROHS Overhead shelf RSCPGC Cafeteria single tubular vertical glass guard RBPG Buffet style protector guard RBPGC Classic tubular glass buffet guard Amperage NEMA Cap Number Ship Wt. 208V 240V 208V 240V (lbs) R2-HF P 6-15P 245 R3-HF P 6-30P 270 R4-HF P 6-30P 295 R5-HF P 6-50P 335 R6-HF P 6-50P 360 *Amperage/NEMA plug type may vary with options Petite Reflections is 30 high-under counter storage is shortened and does not have intermediate shelf RBPGIL Buffet style protector guard with incandescent RBPGFL Buffet style protector guard with fluorescent RBPGH Buffet style protector guard with heat strips RBPG1 Single sided buffet style protector guard RBPG1C Classic single sided tubular glass buffet guard RBPG1IL Single sided buffet style protector guard with incandescent RBPG1FL Single sided buffet style protector guard with fluorescent RBDD Two tier buffet protector guard RBDDL Two tier buffet protector guard with fluorescent RBEG Buffet end guards (pr) ROU Open under storage with shelf RHD Under storage hinged doors RHU Heated storage base with doors and pan slides (convertible racks hold 10-2 deep 12 x 20 pans or x 26 bun pans) RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (120V, 15 AMP) RDRN Drain and manifold with shut-off valve RBKR Common circuit breaker for well heaters only FF Fill Faucet DIMENSION ADDITIONS FOR OPTIONS Add 23-3/4 to height for buffet protector guard Add 14 to height for cafeteria protector guard Add 22-3/4 to height for double display shelf Add 8 to width for cutting board Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Note: Line-up drawing required when ordering interconnected units. LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 53

4 Hot Top JOB ITEM # QTY # MODEL NUMBER R1-HT R2-HT R3-HT R4-HT R5-HT R6-HT R3-HT Perfect for holding pizza or other hot entrees, the Hot Top unit will hold your hot food at just the right serving temperature. The versatile modular design allows you either a cafeteria or a buffet unit to fit your line-up. Reflections units are compatible and will interlock with other Reflections units. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base An insulated heat blanket is securely mounted to the underside of the top. Surface temperature is controlled by an infinite control with pilot light 4 diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units DIMENSIONS R1-HT - 36 H x 30 D x 28 L R2-HT - 36 H x 30 D x 36 L R3-HT - 36 H x 30 D x 50 L R4-HT - 36 H x 30 D x 60 L R5-HT - 36 H x 30 D x 74 L R6-HT - 36 H x 30 D x 96 L 36 height on all standard units 30 height is available on Petite units ELECTRICAL All units available 120 volt standard Six foot electrical cord and plug STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides Protector guards Under storage, hinged doors See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-2 54

5 Hot Top Model# (A) Length Width (B) Height 120V Wattage Amps NEMA Cap Number Ship Wt. (lbs) Ship Class R1-HT P R2-HT P R3-HT P R4-HT P R5-HT P R6-HT P DIMENSION ADDITIONS FOR OPTIONS Add 23-3/4 to height for buffet protector guard Add 14 to height for cafeteria protector guard Add 8 to width for cutting board Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Note: Line-up drawing required when ordering interconnected units. RSCB 8 stainless steel cutting board RMCB 8 maple cutting board RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RSES End shelf - drop type RBHL Heat lamps, bullet-type (buffet only) RCPG Cafeteria style protector guard RCPGC Classic tubular glass cafeteria guard RCPGL Cafeteria style protector guard with incandescent RCPGFL Cafeteria style protector guard with fluorescent RCPGHL Cafeteria style protector guard with heat and light strips RCPGH Cafeteria style protector guard with heat strips RCDD Two tier cafeteria protector guard RCDDC Classic two tier tubular glass cafeteria guard RCDDL Two tier cafeteria protector guard with fluorescent RCEG Cafeteria end guards (pr) ROHS Overhead shelf RSCPGC Cafeteria single tubular vertical glass guard RBPG Buffet style protector guard RBPGC Classic tubular glass buffet guard RBPGIL Buffet style protector guard with incandescent RBPGFL Buffet style protector guard with fluorescent RBPGH Buffet style protector guard with heat strips RBPG1 Single sided buffet style protector guard RBPG1C Classic single sided tubular glass buffet guard RBPG1IL Single sided buffet style protector guard with incandescent RBPG1FL Single sided buffet style protector guard with fluorescent RBDD Two tier buffet protector guard RBDDL Two tier buffet protector guard with fluorescent RBEG Buffet end guards (pr) ROU Open under storage with shelf RHD Under storage hinged doors RHU Heated storage base with doors and pan slides (convertible racks hold 10-2 deep 12 x 20 pans or x 26 bun pans) RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (120V, 15 AMP) B-2 LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 55

6 Hot/Cold Combo Unit JOB ITEM # QTY # MODEL NUMBER R1H2CM R1H5CM R1H3CM R2H4CM R1H4CM R3H3CM R2H3CM R4H2CM R3H2CM R1H2CI R1H3CI R1H4CI R2H3CI R3H2CI R1H5CI R2H4CI R3H3CI R4H2CI R3H3CM operator s side shown with optional CPG protector guard The Reflections Hot/Cold Combo units are ideal for use in cafeteria/buffet lines, school line-ups, hospital cafeterias and lounges. With works-in-a-drawer access, these units are easy to maintain. The Reflections units are compatible and will interlock with other Piper Reflections units. Only Piper's equipment has the advantage of technology and certification. This ensures that your food is kept "out of the DANGER-ZONE." Food spoilage occurs mainly because of rapidly accelerated bacteriological activity within the 40F-140F "DANGER-ZONE." With hot food stays above 140 F longer and cold food is kept below 40 F. Both are key factors in HACCP compliance and the fight against foodborne pathogens. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base Patented Works-in-a-drawer allows element access without removal of unit top 4 diameter swivel plate casters, 2 with brakes Interlocking mechanism is provided to interlock with other Reflections units REFRIGERATION SYSTEM (CM UNITS) Fully hermetic condensing unit located on slide-out rails behind removable louvered panels for crossflow ventilation Welded watertight well 5 deep has a concealed continuous refrigerated coil bond to the bottom and is fully insulated ICE-COOLED COLD PAN (CI UNITS) 5 deep ice-cooled fully welded, watertight pan of 20-gauge stainless steel is fully insulated, 3/4" FPT ball valve provided under unit. HOT FOOD UNIT 20-gauge stainless steel bottom-mounted wet/dry food wells with 12 x 20 die-stamped opening and 1/4 raised beaded edge 208VAC/1000W or 240VAC/1330W heating element per well wired to a thermostat mounted to the control panel DIMENSIONS R1H2CM or R1H2CI - 36 H x 30 D x 50 L R1H3CM or R1H3CI - 36 H x 30 D x 60 L R1H4CM or R1H4CI - 36 H x 30 D x 74 L R2H3CM or R2H3CI - 36 H x 30 D x 74 L R3H2CM or R3H2CI - 36 H x 30 D x 74 L R1H5CM or R1H5CI - 36 H x 30 D x 96 L R2H4CM or R2H4CI - 36 H x 30 D x 96 L R3H3CM or R3H3CI - 36 H x 30 D x 96 L R4H2CM or R4H2CI - 36 H x 30 D x 96 L ELECTRICAL All units available in 208 or 240 volt, single-phase standard Seven foot electrical cord and plug Some options or accessories may not be available with certain voltages STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-3 56

7 Hot/Cold Combo Unit Ice Cooled Refrig. Hot Wells Cold Wells Length *Amps 120/208 Nema Plug Type CI Ship Wt. CM Ship Wt. R1H2CI R1H2CM P R1H3CI R1H3CM P R1H4CI R1H4CM P R2H3CI R2H3CM P R3H2CI R3H2CM P R1H5CI R1H5CM P R2H4CI R2H4CM P R3H3CI R3H3CM P R4H2CI R4H2CM P *Petite Reflections is 30 high - under counter storage is shortened and does not have intermediate shelf. *Amperage/NEMA plug type may vary with options. *Specify voltage 208/60/1 or 240/60/1. RSCB 8 stainless steel cutting board RMCB 8 maple cutting board RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RSES End shelf - drop type RBHL Heat lamps, bullet-type (buffet only) RCPG Cafeteria style protector guard RCPGC Classic tubular glass cafeteria guard RCPGL Cafeteria style protector guard with incandescent RCPGFL Cafeteria style protector guard with fluorescent RCPGHL Cafeteria style protector guard with heat and light strips RCPGH Cafeteria style protector guard with heat strips RCDD Two tier cafeteria protector guard RCDDC Classic two tier tubular glass cafeteria guard RCDDL Two tier cafeteria protector guard with fluorescent RCEG Cafeteria end guards (pr) ROHS Overhead shelf RSCPGC Cafeteria single tubular vertical glass guard RBPG Buffet style protector guard RBPGC Classic tubular glass buffet guard RBPGIL Buffet style protector guard with incandescent RBPGFL Buffet style protector guard with fluorescent RBPGH Buffet style protector guard with heat strips RBPG1 Single sided buffet style protector guard RBPG1C Classic single sided tubular glass buffet guard RBPG1IL Single sided buffet style protector guard with incandescent RBPG1FL Single sided buffet style protector guard with fluorescent RBDD Two tier buffet protector guard RBDDL Two tier buffet protector guard with fluorescent RBEG Buffet end guards (pr) ROU Open under storage with shelf RHD Under storage hinged doors RHU Heated storage base with doors and pan slides (convertible racks hold 10-2 deep 12 x 20 pans or x 26 bun pans) RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (120V, 15 AMP) RDRN Drain and manifold with shut-off valve RBKR Common circuit breaker for well heaters only FF Fill Faucet B-3 LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 57

8 Cold Food Unit Ice or Mechanically Refrigerated JOB ITEM # QTY # MODEL NUMBER R2-CI R3-CI R4-CI R5-CI R6-CI R2-CM R3-CM R4-CM R5-CM R6-CM R5-CM shown with optional 3-ribbed tray slide The Piper Cold Food Units are available mechanically cooled (R-CM) or ice only (R-CI). These units are designed to serve a variety of refrigerated food products and are ideal as a salad bar merchandiser. The versatile modular design allows you either a cafeteria or a buffet unit to fit your line-up. Reflections units are compatible and will interlock with other Reflections units. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base 20-gauge stainless steel fully welded 5 deep cold pan The welded, watertight well has a concealed continuous refrigeration coil bonded to the underside and is fully insulated on R-CM Cold pan has a 3/4" FPT ball valve located below the unit 4 diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units ELECTRICAL - R-CM UNITS ONLY Units available in 120 volt standard Seven foot electrical cord and plug DIMENSIONS R2-CI - 36 H x 30 D x 36 L R3-CI - 36 H x 30 D x 50 L R4-CI - 36 H x 30 D x 60 L R5-CI - 36 H x 30 D x 74 L R6-CI - 36 H x 30 D x 96 L R2-CM - 36 H x 30 D x 36 L R3-CM - 36 H x 30 D x 50 L R4-CM - 36 H x 30 D x 60 L R5-CM - 36 H x 30 D x 74 L R6-CM - 36 H x 30 D x 96 L 36 height on all standard units REFRIGERATION - R-CM UNITS ONLY 1/3 horsepower compressor Fully hermetic condensing unit, located on slide-out rails behind removable louvered panels for cross-flow ventilation Fan-cooled condensing unit with an expansion valve pressure control switch Refrigerant coils shall be of copper tubing attached to the bottom of the well STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides Protector guards See reverse side for additional options B-4 58

9 Cold Food Unit Ice or Mechanically Refrigerated Model# 12x20 Pan Capacity (A) Length Width (B) Height *Amps 120V *NEMA Cap No. Ship Wt. (lbs) Model# Ship Wt. (lbs) R2-CM P 350 R2-CI 200 R3-CM P 485 R3-CI 245 R4-CM P 500 R4-CI 280 R5-CM P 580 R5-CI 330 R6-CM P 640 R6-CI 390 *Amperage/NEMA plug type may vary with options Petite Reflections is 30 high-under counter storage is shortened and does not have intermediate shelf DIMENSION ADDITIONS FOR OPTIONS Add 23-3/4 to height for buffet protector guard Add 14 to height for cafeteria protector guard Add 22-3/4 to height for 2-tier display stand Add 8 to width for cutting board Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Note: Line-up drawing required when ordering false front, cashier stand or interconnected units. B-4 RSCB 8 stainless steel cutting board RMCB 8 maple cutting board RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RSES End shelf - drop type RBHL Heat lamps, bullet-type (buffet only) RCPG Cafeteria style protector guard RCPGC Classic tubular glass cafeteria guard RCPGL Cafeteria style protector guard with incandescent RCPGFL Cafeteria style protector guard with fluorescent RCPGHL Cafeteria style protector guard with heat and light strips RCPGH Cafeteria style protector guard with heat strips RCDD Two tier cafeteria protector guard RCDDC Classic two tier tubular glass cafeteria guard RCDDL Two tier cafeteria protector guard with fluorescent RCEG Cafeteria end guards (pr) ROHS Overhead shelf RSCPGC Cafeteria single tubular vertical glass guard RBPG Buffet style protector guard RBPGC Classic tubular glass buffet guard RBPGIL Buffet style protector guard with incandescent RBPGFL Buffet style protector guard with fluorescent RBPGH Buffet style protector guard with heat strips RBPG1 Single sided buffet style protector guard RBPG1C Classic single sided tubular glass buffet guard RBPG1IL Single sided buffet style protector guard with incandescent RBPG1FL Single sided buffet style protector guard with fluorescent RBDD Two tier buffet protector guard RBDDL Two tier buffet protector guard with fluorescent RBEG Buffet end guards (pr) ROU Open under storage with shelf RHD Under storage hinged doors RHU Heated storage base with doors and pan slides (convertible racks hold 10-2 deep 12 x 20 pans or x 26 bun pans) RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (120V, 15 AMP) RDRN Drain and manifold with shut-off valve RBKR Common circuit breaker for well heaters only RMRCE Extended compressor warranty LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 59

10 Frost Top Mechanically Refrigerated JOB ITEM # QTY # MODEL NUMBER R2-FT R3-FT R4-FT R5-FT R6-FT R4-FT Frost Top units are perfect for dessert and salad merchandising such as parfaits, pastry, jello and a variety of salads. The versatile modular design allows you either a cafeteria or a buffet unit to fit your line-up. Reflections units are compatible and will interlock with other Reflections units. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base Mechanically cooled and thermostatically controlled top of 14-gauge stainless steel The welded, watertight well has a concealed continuous refrigeration coil bonded to the underside and is fully insulated Cross-flow ventilation has two stainless steel exterior frames with removable stainless steel louvers for easy access Fully hermatic condensing unit shall be connected to the frost top and controls, sized to the evaporator load Condensing unit on slide-out rails for ease of service Full perimeter drain trough has a 3/4" FPT drain valve below the base 4 diameter swivel plate casters, 2 with brakes Interlocking mechanism is provided to interlock with other Reflections units DIMENSIONS R2-FT - 36 H x 30 D x 36 L R3-FT - 36 H x 30 D x 50 L R4-FT - 36 H x 30 D x 60 L R5-FT - 36 H x 30 D x 74 L R6-FT - 36 H x 30 D x 96 L 36 height on all standard units 30 height is available on Petite Elite units ELECTRICAL All units available in 120 volt, single-phase standard Six foot electrical cord and plug STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides, cutting boards Protector guards Under storage, hinged doors Common drains and manifolds See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-5 60

11 Frost Top Mechanically Refrigerated Model# (A) Length (B) Height 120V Wattage Amperage 120V NEMA Plug Type Ship Wt. (lbs) R2-FT P 380 R3-FT P 460 R4-FT P 550 R5-FT P 620 R6-FT P 690 DIMENSION ADDITIONS FOR OPTIONS Add 23-3/4 to height for buffet protector guard Add 14 to height for cafeteria protector guard Add 8 to width for cutting board Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Note: Line-up drawing required when ordering interconnected units. B-5 RSCB 8 stainless steel cutting board RMCB 8 maple cutting board RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RSES End shelf - drop type RBHL Heat lamps, bullet-type (buffet only) RCPG Cafeteria style protector guard RCPGC Classic tubular glass cafeteria guard RCPGL Cafeteria style protector guard with incandescent RCPGFL Cafeteria style protector guard with fluorescent RCPGHL Cafeteria style protector guard with heat and light strips RCPGH Cafeteria style protector guard with heat strips RCDD Two tier cafeteria protector guard RCDDC Classic two tier tubular glass cafeteria guard RCDDL Two tier cafeteria protector guard with fluorescent RCEG Cafeteria end guards (pr) ROHS Overhead shelf RSCPGC Cafeteria single tubular vertical glass guard RBPG Buffet style protector guard RBPGC Classic tubular glass buffet guard RBPGIL Buffet style protector guard with incandescent RBPGFL Buffet style protector guard with fluorescent RBPGH Buffet style protector guard with heat strips RBPG1 Single sided buffet style protector guard RBPG1C Classic single sided tubular glass buffet guard RBPG1IL Single sided buffet style protector guard with incandescent RBPG1FL Single sided buffet style protector guard with fluorescent RBDD Two tier buffet protector guard RBDDL Two tier buffet protector guard with fluorescent RBEG Buffet end guards (pr) ROU Open under storage with shelf RHD Under storage hinged doors RHU Heated storage base with doors and pan slides (convertible racks hold 10-2 deep 12 x 20 pans or x 26 bun pans) RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (120V, 15 AMP) RDRN Drain and manifold with shut-off valve RBKR Common circuit breaker for well heaters only LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 61

12 Cool Breeze Unit Listed NSF/ANSI Standard 7 JOB ITEM # QTY # MODEL NUMBER R3-CB R4-CB R5-CB R6-CB R4-CB shown with optional 3-ribbed tray slide and 2-tier display stand The Cool Breeze unit is ideal for the front-of-the house for salad bars and kiosks and is the perfect product for cookchill tray lines where cold food temperature maintenance is a must. The Cool Breeze system maintains a cold flow of air moving over the product while not drying it out or allowing it to freezer burn. Reflections units are compatible and will interlock with other Reflections units. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base Fully enclosed and insulated 4-3/4 deep well with electronic thermostat Fan cooled refrigeration unit located on slide-out interior housing behind removable louvered panels for cross-flow ventilation Heated condensate pan Adaptable for up to 4 deep pans or custom displays 4 diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units Drain provided with 3/4" FPT ball valve under unit. ELECTRICAL Units available in 120 volt standard Seven foot electrical cord and plug DIMENSIONS R3-CB - 36 H x 30 D x 50 L R4-CB - 36 H x 30 D x 60 L R5-CB - 36 H x 30 D x 74 L R6-CB - 36 H x 30 D x 96 L 36 height on all standard units NSF/ANSI STANDARD 7 This unit is listed with CSA in NSF/ANSI Standard 7 for design and construction and has been performance tested for the storage of potentially hazardous foods. The performance test criteria is holding a food-like media at or below 41 F without any freezing for four hours at 86 F ambient temperature. REFRIGERATION SYSTEM 1/3 horsepower compressor Fan-cooled condensing unit with an expansion valve pressure control switch Refrigerant coils shall be of copper tubing attached to the bottom of the well STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides Protector guards See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-6 62

13 Cool Breeze Unit Listed NSF/ANSI Standard 7 Model# (A) Length Width (B) Height 120V Wattage Amps. 120V NEMA Cap No. RSCB 8 stainless steel cutting board RMCB 8 maple cutting board RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RSES End shelf - drop type RBHL Heat lamps, bullet-type (buffet only) RCPG Cafeteria style protector guard RCPGC Classic tubular glass cafeteria guard RCPGL Cafeteria style protector guard with incandescent RCPGFL Cafeteria style protector guard with fluorescent RCPGHL Cafeteria style protector guard with heat and light strips RCPGH Cafeteria style protector guard with heat strips RCDD Two tier cafeteria protector guard RCDDC Classic two tier tubular glass cafeteria guard RCDDL Two tier cafeteria protector guard with fluorescent RCEG Cafeteria end guards (pr) ROHS Overhead shelf RSCPGC Cafeteria single tubular vertical glass guard RBPG Buffet style protector guard RBPGC Classic tubular glass buffet guard RBPGIL Buffet style protector guard with incandescent Ship Wt. (lbs) R3-CB P 520 R4-CB P 548 R5-CB P 625 R6-CB P 640 Petite Reflections is 30 high - under counter storage is shortened and does not have intermediate shelf DIMENSION ADDITIONS FOR OPTIONS Add 23-3/4 to height for buffet protector guard Add 14 to height for cafeteria protector guard Add 8 to width for cutting board Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Add 22-3/4 to height for 2-tier display stand Add 32-1/4 to height for 3-tier display stand Note: Line-up drawing required when ordering interconnected units. RBPGFL Buffet style protector guard with fluorescent RBPGH Buffet style protector guard with heat strips RBPG1 Single sided buffet style protector guard RBPG1C Classic single sided tubular glass buffet guard RBPG1IL Single sided buffet style protector guard with incandescent RBPG1FL Single sided buffet style protector guard with fluorescent RBDD Two tier buffet protector guard RBDDL Two tier buffet protector guard with fluorescent RBEG Buffet end guards (pr) ROU Open under storage with shelf RHD Under storage hinged doors RHU Heated storage base with doors and pan slides (convertible racks hold 10-2 deep 12 x 20 pans or x 26 bun pans) RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (120V, 15 AMP) RDRN Drain and manifold with shut-off valve RBKR Common circuit breaker for well heaters only RMRCE Extended compressor warranty RRU Refrigerated storage base with doors and pan slides: holds 8-2" deep 12"x20" pans B-6 LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 63

14 Solid Top Unit JOB ITEM # QTY # MODEL NUMBER R1-ST R2-ST R3-ST R4-ST R5-ST R6-ST R5-ST shown with optional 3-ribbed tray slide and BPG protector guard The Reflections Solid Top units are ideal for use as worktops, for plating and for sandwich and salad preparation. This unit can also be used as a counter for other serving and merchandising needs. The design allows it to be used in a cafeteria or buffet line-up, choosing the options and accessories that you need. All Reflections units are compatible and will interlock with other Reflections units. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base Underbracing for heavier loads 4 diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units DIMENSIONS R1-ST - 36 H x 30 D x 28 L R2-ST - 36 H x 30 D x 36 L R3-ST - 36 H x 30 D x 50 L R4-ST - 36 H x 30 D x 60 L R5-ST - 36 H x 30 D x 74 L R6-ST - 36 H x 30 D x 96 L 36 height on all standard units STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides Protector guards Under storage, hinged doors See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-7 64

15 Solid Top Unit Model# (A) Length Width (B) Height Ship Wt. (lbs) R1-ST R2-ST R3-ST R4-ST R5-ST R6-ST Petite Reflections is 30 high - under counter storage is shortened and does not have intermediate shelf DIMENSION ADDITIONS FOR OPTIONS Add 14 to height for cafeteria protector guard Add 22-3/4 to height for 2-tier display stand Add 32-1/4 to height for 3-tier display stand Add 8 to width cutting board Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Note: Line-up drawing required when ordering interconnected units. B-7 RSCB 8 stainless steel cutting board RMCB 8 maple cutting board RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RSES End shelf - drop type RBHL Heat lamps, bullet-type (buffet only) RCPG Cafeteria style protector guard RCPGC Classic tubular glass cafeteria guard RCPGL Cafeteria style protector guard with incandescent RCPGFL Cafeteria style protector guard with fluorescent RCPGHL Cafeteria style protector guard with heat and light strips RCPGH Cafeteria style protector guard with heat strips RCDD Two tier cafeteria protector guard RCDDC Classic two tier tubular glass cafeteria guard RCDDL Two tier cafeteria protector guard with fluorescent RCEG Cafeteria end guards (pr) ROHS Overhead shelf RSCPGC Cafeteria single tubular vertical glass guard RBPG Buffet style protector guard RBPGC Classic tubular glass buffet guard RBPGIL Buffet style protector guard with incandescent RBPGFL Buffet style protector guard with fluorescent RBPGH Buffet style protector guard with heat strips RBPG1 Single sided buffet style protector guard RBPG1C Classic single sided tubular glass buffet guard RBPG1IL Single sided buffet style protector guard with incandescent RBPG1FL Single sided buffet style protector guard with fluorescent RBDD Two tier buffet protector guard RBDDL Two tier buffet protector guard with fluorescent RBEG Buffet end guards (pr) ROU Open under storage with shelf RHD Under storage hinged doors RHU Heated storage base with doors and pan slides (convertible racks hold 10-2 deep 12 x 20 pans or x 26 bun pans) RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (120V, 15 AMP) RDRN Drain and manifold with shut-off valve RBKR Common circuit breaker for well heaters only RMRCE Extended compressor warranty LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 65

16 Beverage Counter JOB ITEM # QTY # R96-BEV1 shown with optional solid ribbed tray slide Designed to keep your serving area clean and functional, these Piper Beverage Counters are sure to complete your line-up. The standard full length drains will keep hazardous spills from your floors. Units are a full 30 deep to accommodate nearly all coffee makers. The versatile modular design allows you to design a cafeteria or buffet unit to fit your line-up. All Reflections units are compatible and will interlock with other Reflections units. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base Under bracing for heavier loads 4-1/2" wide stainless steel removable grate for easy access 3/4" FPT ball valve provided under unit 4" diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units ELECTRICAL Optional outlet locations must be specified MODEL NUMBER R1-BEV1 R2-BEV1 R3-BEV1 R4-BEV1 DIMENSIONS R5-BEV1 R6-BEV1 R1-BEV2 R2-BEV2 R1-BEV1-36 H x 30 D x 28 L R2-BEV1-36 H x 30 D x 36 L R3-BEV1-36 H x 30 D x 50 L R4-BEV1-36 H x 30 D x 60 L R5-BEV1-36 H x 30 D x 74 L R6-BEV1-36 H x 30 D x 96 L R1-BEV2-36 H x 30 D x 28 L R2-BEV2-36 H x 30 D x 36 L R3-BEV2-36 H x 30 D x 50 L R4-BEV2-36 H x 30 D x 60 L R5-BEV2-36 H x 30 D x 74 L R6-BEV2-36 H x 30 D x 96 L 36 height on all standard units STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides Cutting boards Under storage, hinged doors See reverse side for additional options. WARRANTY R3-BEV2 R4-BEV2 R5-BEV2 R6-BEV2 One year parts and labor. Warranty is detailed on inside front cover of the price list. B-8 66

17 Beverage Counter Model# (A) Length Width (B) Height Ship Wt. (lbs) R1-BEV R2-BEV R3-BEV R4-BEV R5-BEV R6-BEV R1-BEV R2-BEV R3-BEV R4-BEV R5-BEV R6-BEV BEV1 - single trough BEV2 - double trough Petite Reflections is 30 high - under counter storage is shortened and does not have intermediate shelf RSCB 8 stainless steel cutting board RMCB 8 maple cutting board RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RSES End shelf - drop type ROU Open under storage with shelf RHD Under storage hinged doors RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (verify electrical requirements) DIMENSION ADDITIONS FOR OPTIONS Add 8 to width for cutting board Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Note: Line-up drawing required when ordering interconnected units. B-8 LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 67

18 Cashier Stand JOB ITEM # QTY # MODEL NUMBER R1-CS R2-CS R1-CS shown with optional solid ribbed tray slide The Reflections Cashier Stand is a comfortable workstation. Ideal for use in cafeteria/buffet lines, school line ups and hospital cafeterias. This Reflections unit is compatible and will interlock with other Reflection units or the Cashier Stand can be operated as a freestanding separate unit. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Open insert lined with 18-gauge stainless\ steel Stainless steel tubular foot rest secured to interior walls Hole in top with bushing for cash register cord Locking drawer Drawer is centered in the panel on the open side and mounted on roller bearing slides 4 diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units DIMENSIONS R1-CS - 36 H x 30 W x 28 D R2-CS - 36 H x 30 W x 36 D 36 height on all standard units STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides Duplex outlet Adjustable bullet feet See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-11 72

19 Cashier Stand Model# (A) Length Width (B) Height Ship Wt. (lbs) R1-CS R2-CS Drawer is 17 wide, 11-1/2 long and 2-1/2 deep Petite models are not available DIMENSION ADDITIONS FOR OPTIONS Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Note: Line-up drawing required when ordering interconnected units. OPTIONS / ACCESSORIES RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (verify electrical requirements) B-11 LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 73

20 Corner Unit JOB ITEM # QTY # MODEL NUMBER R1-CU R1-CU The Reflections Corner Units are ideal for making L-shaped line-ups to fit your specific needs. Optional T line-up is also available. This Reflections unit is compatible and will interlock with other Reflection units. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 30 square 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base 4 diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units DIMENSIONS R1-CU - 36"H x 30 W x 30"D 36 height on all standard units STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides Adjustable bullet feet See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-11-B 74

21 Corner Unit Model# Length Width Height Ship Wt. (lbs) R1-CU Petite models are not available DIMENSION ADDITIONS FOR OPTIONS Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Note: Line-up drawing required when ordering interconnected units. OPTIONS / ACCESSORIES RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RBL Stainless steel 6 adjustable bullet feet ROU Open under storage with shelf RDOUT Duplex outlet (verify electrical requirements) B-11-B LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 75

22 Tray Stand JOB ITEM # QTY # MODEL NUMBER R1-TS R2-TS R1-TS The Reflections Tray Stand is a must to begin your lineup. Its versatile design can provide for all the required utensils. This Reflections unit is compatible and will interlock with other Reflection units. This Tray Stand unit holds virtually all sizes of food trays. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides 4 diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units DIMENSIONS R1-TS - 36"H x 30 D x 28 L (single stack) R2-TS - 36"H x 30 D x 36 L (double stack) 36 height on all standard units STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Bullet feet Silverware dispenser See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-12 76

23 Tray Stand Model# "A" Width "C" Height Ship Wt. (lbs) R1-TS 30" 30" 14" 36" 155 R2-TS " R1-TS is single stack, R2-TS is double stack Petite models are 30" high. Contact factory for details. OPTIONS / ACCESSORIES RBL Stainless steel 6 adjustable bullet feet RSD Silverware dispenser RSDN Silverware and napkin dispenser Note: Line-up drawing required when ordering interconnected units. B-12 LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 77

24 Beverage Cooler CAN BE CUSTOMIZED WITH YOUR LOGO. JOB ITEM # QTY # MODEL NUMBER R2-BCI R3-BCI R4-BCI R3-BCI The Piper Beverage Cooler is good for back bar or self service ice units for beverages. These units are designed to serve a variety of refrigerated food products and are ideal as a salad bar merchandiser. The versatile modular design allows you to do stand alone kiosks, cafeteria or a buffet unit. Units are compatible and will interlock with other Reflections units. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base 20-gauge stainless steel fully welded 5 deep cold pan Welded, watertight well Cold pan has a 3/4" FPT drain ball valve located below the unit 4" diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units DIMENSIONS R2-BCI - 36 H x 30 D x 36 L R3-BCI - 36 H x 30 D x 50 L R4-BCI - 36 H x 30 D x 60 L STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Unit can be customized with your logo Tray slides Protector guards See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-13 78

25 Beverage Cooler Model# 12x20 Pan Capacity (A) Length Width (B) Height Ship Wt. (lbs) Capacity* R2-BCI R3-BCI R4-BCI *Based on 12oz. bottles. Capacities will vary depending on product and ice usage. DIMENSION ADDITIONS FOR OPTIONS Add 23-3/4 to height for buffet protector guard Add 14 to height for cafeteria protector guard Add 22-3/4 to height for 2-tier display stand Add 8 to width for cutting board Add 12-3/4 to width for solid ribbed tray slide Add 12-1/2 to width for 3-bar tray slide Note: Line-up drawing required when ordering false front, cashier stand or interconnected units. B-13 RSCB 8 stainless steel cutting board RMCB 8 maple cutting board RSRTS Solid 3-ribbed tray slide, 16-gauge stainless steel RSFTS Solid flat tray slide, 16-gauge stainless steel R3BTS 3-bar tray slide RSES End shelf - drop type RBHL Heat lamps, bullet-type (buffet only) RCPG Cafeteria style protector guard RCPGC Classic tubular glass cafeteria guard RCPGL Cafeteria style protector guard with incandescent RCPGFL Cafeteria style protector guard with fluorescent RCPGHL Cafeteria style protector guard with heat and light strips RCPGH Cafeteria style protector guard with heat strips RCDD Two tier cafeteria protector guard RCDDC Classic two tier tubular glass cafeteria guard RCDDL Two tier cafeteria protector guard with fluorescent RCEG Cafeteria end guards (pr) ROHS Overhead shelf RSCPGC Cafeteria single tubular vertical glass guard RBPG Buffet style protector guard RBPGC Classic tubular glass buffet guard RBPGIL Buffet style protector guard with incandescent RBPGFL Buffet style protector guard with fluorescent RBPGH Buffet style protector guard with heat strips RBPG1 Single sided buffet style protector guard RBPG1C Classic single sided tubular glass buffet guard RBPG1IL Single sided buffet style protector guard with incandescent RBPG1FL Single sided buffet style protector guard with fluorescent RBDD Two tier buffet protector guard RBDDL Two tier buffet protector guard with fluorescent RBEG Buffet end guards (pr) ROU Open under storage with shelf RHD Under storage hinged doors RHU Heated storage base with doors and pan slides (convertible racks hold 10-2 deep 12 x 20 pans or x 26 bun pans) RBL Stainless steel 6 adjustable bullet feet RDOUT Duplex outlet (120V, 15 AMP) RMRCE Extended Compressor Warranty RRB Perforated false bottom RRU Refrigerated storage base with door and pan slides: holds 8-2" deep 12"x20" pans LIMITED WARRANTY: PIPER PRODUCTS warrants to the original purchaser parts and labor for a period of twelve (12) months from the date of purchase. See manufacturer s complete warranty for details. It is our policy to build equipment which is design certified by companies that have been accredited at the Federal Level by the Occupational Safety and Health Agency (OSHA) and ANSI as a National Recognized Testing Laboratory. These companies include CSA International, Underwriters Laboratories, and the National Sanitation Foundation. However, a continuing program of product improvement makes it necessary to submit new models to the agencies as they are developed. Consequently, all models may not bear the appropriate labels at all times. We reserve the right to change specifications and product design without notice. Such revisions do not entitle buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Information is not for design purposes. 79

26 Bloomington Cold Extra Deep Cold Pan - Listed NSF/ANSI Standard 7 JOB ITEM # QTY # MODEL NUMBER R2-BCM R3-BCM R4-BCM R5-BCM R6-BCM The Piper Bloomington Cold Food Unit features an extra deep cold pan of 9-7/16 deep and is listed NSF/ANSI Standard 7. The Bloomington Cold Units are designed to serve a variety of refrigerated food products, these units are ideal as a salad bar merchandiser. Reflections units are compatible and will interlock with other Reflections units. STANDARD FEATURES Seamless, molded FRP body with smooth exterior and rounded corners 14-gauge stainless steel top with fully welded square turndowns on all sides Enclosed base 20-gauge stainless steel fully welded 9-7/16 deep cold pan Fully hermetic condensing unit, located on slide-out rails behind removable louvered panels for cross-flow ventilation Welded watertight well has a concealed continuous refrigerated coil bonded to the sides and is fully insulated Cold pan has a 3/4" FPT drain ball valve located below the unit 4" diameter swivel plate casters with brakes Interlocking mechanism is provided to interlock with other Reflections units ELECTRICAL Units available in 120 volt standard Seven foot electrical cord and plug REFRIGERATION SYSTEM R5-BCM shown with optional 3-ribbed tray slide 1/3 horsepower compressor Fan-cooled condensing unit with an expansion valve pressure control switch Refrigerant coils shall be of copper tubing wrapped around the sides of the well DIMENSIONS R2-BCM - 36 H x 30 D x 36 L R3-BCM - 36 H x 30 D x 50 L R4-BCM - 36 H x 30 D x 60 L R5-BCM - 36 H x 30 D x 74 L R6-BCM - 36 H x 30 D x 96 L 36 height on all standard units NSF/ANSI STANDARD 7 This unit is listed with CSA in NSF/ANSI Standard 7 for design and construction and has been performance tested for the storage of potentially hazardous foods. The performance test criteria is holding a food-like media at or below 41 F without any freezing for four hours at 86 F ambient temperature. STANDARD COLORS Wine Red (RAL 3005) Signal Red (RAL 3001) Yellow (RAL 1021) Light Blue (RAL 5012) Gentiane Blue (RAL 5010) Water Blue (RAL 5021) Moss Green (RAL 6005) Squirrel Gray (RAL 7000) Black White Custom colors available Optional Graphics Packages available COMMON OPTIONS Tray slides Protector guards Refrigerated storage base See reverse side for additional options WARRANTY One year parts and labor. Warranty is detailed on inside front cover of the price list. B-14 80