Solera Crank Style Awning OWNER'S MANUAL. Rev: Page 1 Solera Crank Awning Owner's Manual

Transcription

1 Solera Crank Style Awning OWNER'S MANUAL Rev: Page 1 Solera Crank Awning Owner's Manual

2 TABLE OF CONTENTS System Information 2 Operation 3 Extending The Awning 3 Retracting The Awning 4 Adjusting Pitch - All Solera Awnings 5 Maintenance - All Solera Awnings 5 Fabric Care 5 Solera Crank Style Awning Assembly 6 Solera Crank Style Awning Components 7 Variant Code Information 7 Ordering Replacement Components 9 System Information The Solera Crank Style Awning extends and retracts with the easy-to-use hook-and-crank tool. Simply insert the hook into the drive head and turn clockwise to extend the awning and counterclockwise to retract the awning. The Solera Crank Style Awning features an internal gear box that allows the awning to stop at any point during extension or retraction. Additionally, the friction joint allows for rain dump and adjustable pitch features, and there is no rafter arm to lock in place. The friction joint also provides added stability the arms don't need to be locked in place like manual awnings. This manual provides operational procedures for the Solera Crank Style Awning. Operating the Solera Crank Style Awning in any other manner than described may result in personal injury, damage to the recreational vehicle or the awning assembly as well as voiding the Lippert Components Limited Warranty. Rev: Page 2 Solera Crank Awning Owner's Manual

3 Operation Extending The Awning 1. Locate the locking latch (Fig. 1), if equipped, and unlock the latch (Fig. 2). Note: This latch is optional and may or may not be installed on one or both support arms. 2. Locate the crank handle for the awning. 3. Insert the hook end of the crank handle into the eye bolt on the drive head (Fig. 3A). 4. Turn the crank in a clockwise direction and fully extend the awning (Fig. 4). Note: Keeping the handle parallel with the awning head support arm makes it easier to turn. Note: Extension is considered complete when the fabric is completely unrolled, the valance seam is visible and a section of the roll tube is exposed (Fig. 5). Tying the roll tube down once the awning is extended will not allow the free floating support arms to work as designed and may cause damage to the awning or RV. Fig. 1 Fig. 3 Fig. 4 Fig. 2 A Fig. 5 - Complete Extension Valance Seam Fabric Roll Tube Valance Exposed Roll Tube Section Awning Head Rev: Page 3 Solera Crank Awning Owner's Manual

4 Retracting The Awning Note: The awning can be retracted without resetting the pitch (see Page 5.) 1. Insert the hook end of the crank handle into the eye bolt on the drive head (Fig. 6). 2. Turn the crank handle in a counterclockwise direction until the awning is fully retracted (Figs. 7 and 8). NOTE: Keeping the handle parallel with the awning head support arm makes it easier to turn. 3. Locate the locking latch (Fig. 9), if equipped, and lock the latch (Fig. 10). Note: This latch is optional and may or may not be installed on one or both support arms. If not installed, awning is secured and ready for transportation. Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Rev: Page 4 Solera Crank Awning Owner's Manual

5 Adjusting Pitch - All Solera Awnings Note: The awning will pitch itself to purge the pooling of excess water and may dump a significant amount of water without notice. 1. Pitch can be set by adjusting the articulating arm to tip one side of the awning to allow water runoff. 2. Extend the awning to desired position. 3. Choose the side of the awning for optimum shade or convenient water runoff. Pull downward on the joint of the articulating arm until desired pitch is set (Fig. 11) to allow for water runoff. Do not push the joints of the articulating arms up. This will put tension on the gas strut, which can cause the strut to break. Belleville washers and bolt (Fig. 12A) allow for the joint to remain in the position set by the operator. Note: The awning can be retracted without resetting the pitch. If the articulating arm does not hold position, it can be tightened by adjusting the bolt (Fig. 12A) in the center of the articulating arm. Fig. 11 Fig. 12 Pitch A Maintenance - All Solera Awnings Fabric Care If the awning is rolled up while wet, roll it out and let it dry as soon as conditions allow before rolling it up again. This will help prevent the formation of mildew and add greatly to the life of the awning. Mildew does not form on the fabric itself, but on the accumulated dust, dirt and grime. Note: Periodically clean vinyl or woven acrylic fabric using a mixture of 1/4 cup of dish soap and 5 gallons of warm water. Liberally slosh the mixture on the top of the fabric and roll up the awning for 5 minutes. This will apply the mixture to the bottom of the fabric as well. Roll the awning back out and hose off with fresh water. Repeat if necessary. Allow to dry before rolling up. Rev: Page 5 Solera Crank Awning Owner's Manual

6 SOLERA CRANK STYLE AWNING ASSEMBLY AWNINGS Idler Side Head Crank Handle End Cap Gearbox Head Grommet Awning Fabric #8 Wax Screw Grommet Diaphragm Support Arm Assembly Box Gear with Eyelet Gearbox Head X-Ray View Pin Coupler Screw Box Gear with Eyelet Gas Strut Nylock Nut Roll Tube Rev: Page 6 Solera Crank Awning Owner's Manual

7 SOLERA CRANK STYLE AWNING COMPONENTS AWNINGS A Variant Code Information Solera Awnings have a sticker located on the roll tube with a variant code that is specific to that awning assembly. The sticker on newer units will be located near the gearbox head on the roll tube. There will also be a sticker on the awning fabric. The variant code will determine which variation of the product is being used. When ordering replacement parts, it is imperative to use the variant code to receive the most compatible part. Roll Tube Variant Code Eyelet Detail B D C E G F Callout White Part # Black Part # Description A Idler Side Head B Gearbox C Nut 1/4" - 20 Nylock (for Box Gear) D Box Gear, Manual, with Eyelet (gear will come disassembled) E Coupler (for Box Gear) F Screw 1/4" - 20 x 1 1/8" (for Box Gear) G Pin, Spring Slotted (for Box Gear) Rev: Page 7 Solera Crank Awning Owner's Manual

8 A B C D F E G H I J Callout White Part # Black Part # Description A Screw - # 8-15 x 1/2" B Screw - #6 x 1/2" (fastener for head covers, 6 per cover) C #8 End Cap Wax Screw (head to roll tube) D Screw - #8-32 x 1/2" (back cover to mount) E Nut 5/16"-18 Nylock (head to arm) F Screw 5/16"-18 x 2-1/4" (head to arm) G Crank Handle H End Cap I Rubber Grommet J Grommet Diaphragm Rev: Page 8 Solera Crank Awning Owner's Manual

9 A B C D AF E Callout White Part # Black Part # Description Support Arm Assembly (Short, 61") (One Arm) A Support Arm Assembly (Pitched, 66 1/8") (One Arm) Support Arm Assembly (Flat, 69") (One Arm) B Gas Strut; 26"; 124 LBS (for Short and Flat Arm assemblies) Gas Strut; 26"; LBS (for Pitched Arm assemblies) C Screw - #14-10 x 1 1/2 (arms to coach) D Star Washer (for Gas Strut and Holding Pins) Awning Cradle E NOTE: Only required for Solera Awnings greater than 21' in length F Awning Idler Head Mount Awning Drive Head Mount Ordering Replacement Components 1. Locate the Solera sticker on the roll tube or the awning fabric. 2. Locate the variant code at the bottom of the sticker. 3. Call LCI Customer Service at (574) and provide the variant code. Roll Tube Variant Code Rev: Page 9 Solera Crank Awning Owner's Manual

10 The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. ( LCI ). LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty. The information contained in this manual is subject to change without notice and at the sole discretion of LCI. Revised editions are available for free download from Please recycle all obsolete materials. For all concerns or questions, please contact Lippert Components, Inc. Ph: (574) Web: lci1.com customerservice@lci1.com Rev: Page 10 Solera Crank Awning Owner's Manual