Installation Instructions
|
|
- Asher Garrett
- 6 years ago
- Views:
Transcription
1 Installation Instructions EPK12, EPK16, EPK20 & EPK24 Entrance Panels 2) Mount brass Extension Bars to Interior Ground Bar using hardware provided. Figure #3. EPK12 Figure #1: Assembled Entrance Panel NOTE: EPK panels are shipped in a master package that contains two boxes. One contains components for Shelter Installation and the other for Field Installation. EPK12 is shown for illustrative purposes. SHELTER INSTALLATION 1) Predrill (2) 1 diameter through holes approximately 6 below the opening for the waveguide entry panel. Holes should be centered underneath entry panel. Figure #2. Figure #3: Interior Ground Bar 3) Mount Interior Ground Bar to wall surface. (Hardware not included) 4) Mount Exterior Ground Bar to brass Extension Bars using hardware provided. Figure #4. Figure #4: Exterior Ground Bar Figure #2: Through Hole Interior View Rev. 5/5/ Ziegler Drive, Grayslake, IL Phone: Fax: Website: 1
2 5) When installed the Exterior Ground Bar will extend between 3-1/2 to 5-1/2 from the shelter depending on wall thickness. Figure #5. EXTERIOR FIELD INSTALLATION Option A: (Preferred Method) At time of ground electrode installation Option B: After ground electrode installation Option A: 1A) Place Ground Plate Assembly in trench 6 below frost line and 2 away from building. Figures #7 and #8. Figure #5: Exterior Ground Bar Location 6) Shelter Installation Complete. Assembly Shown. Figure #6. Figure #7: Option A Installation Figure #6: Complete Shelter Installation Figure #8: Option A (Cross Section) 2
3 2A) Loosen fasteners holding Flat Strap Ground Clamps to Exterior Ground Bar enough to apply Antioxidant Joint Compound (supplied) to the inside of the Clamps and to the Ground Bar. Unroll Ground Straps and pull them up through the Clamps and Ground Bar. Tighten Clamps securing the Ground Straps. Cut off any excess Strap. Figure #9. 4A) Fasten Ground Straps to side of shelter using channel support (EPKPPCST) and appropriate fasteners (EPKPPCST and fasteners not included). Figure #11. Protective Plastic Channel Support (EPKPPCST) Flat Strap Ground Clamp Ground Plate Assembly Figure #9: Ground Strap Attachment 3A) Connect the #2 AWG solid tinned tails of the Ground Plate Assembly to the #2 solid tinned ground ring using a #BS2SB Ultraweld mold with a UWM32 weld metal. Requires two connections. Figure #10. Figure #11: Ground Strap Support 5A) Backfill trench and around Ground Plate Assembly. Exterior installation complete. Ready for installation of Coax Ground Kits (Not Included). Figure #12. Figure #10: Connection to Ground Ring Figure #12: Option A Exterior Complete 3
4 Option B: 1B) When installing Ground Electrode System, stub up two pigtails for later installation of Ground Plate Assembly. Figure #13. 3B) Reference (2A) for instructions on installation of Flat Ground Straps to the Exterior Ground Bar. Figure #7. 4B) Fasten Ground Straps to side of shelter using appropriate fasteners (Not Included). Figure #11. 5B) Backfill trench and around Ground Plate Assembly. Exterior installation complete. Ready for installation of Coax Ground Kits (Not Included). Figure #15. Figure #13: Option B Installation 2B) Trench down 6 to 12 for installation of Ground Plate Assembly. Cut stubbed up pigtails and the pigtails on the Ground Plate Assembly to allow for a BS2SB (UWM 32) connection at both locations. A PT2S2SB (UWM65) if a BS2SB is not available. Figure #14. Figure #15: Option B Exterior Complete Go To Next Page Figure #14: Connection to Ground Ring 4
5 INTERIOR FIELD INSTALLATION 1) Mount Arrestor Ground Straps as needed to the Interior Ground Bar with the stainless steel hardware supplied. Figure #16. Arrestor Ground Straps 3) For a Flange Mounted Lightning Arrestor, the end of the Arrestor Ground Strap can be cut off to accommodate the flange connection. Figure #18. Flange Mounted Lightning Arrestor Interior Ground Bar Figure #16: Arrestor Ground Straps Arrestor Ground Strap Figure #18: Flange Mount Arrestor 2) Arrestor Ground Straps can be attached to either Type N Bulkhead or Flange Mounted Lightning Arrestors. A typical mounting of Type N Arrestors are shown in Figure 17. Figure #17: Type N Arrestor/Ground Strap Installation 5
ZICO 3090PM4. Horizontal Hard Suction Mount Kits HHS-TM-1, HHS-TM-2, HHS-TM-1-ST, HHS-TM-2-ST, HHS-TMV-2, HHS-TMV-2-ST Parts and Instruction Manual
Horizontal Hard Suction Mount Kits Models HHS-TM-1, HHS-TM-2, HHS-TM-1-ST, HHS-TM-2-ST, HHS-TMV-2, HHS-TMV-2-ST Parts and Instruction Manual ZICO 3090PM4 Rev. 9-27-18 I. SYSTEMS AVAILABLE A. HHS-TM-1:
More informationTarp Return. Questions? Contact Customer Or Parts Diagrams see Parts and Diagrams section on web at
Roll Rite, LLC and its entire staff would like to not only Thank You but congratulate you on your purchase of one of what we feel to be the finest line of tarping systems in the industry. Tarp Return RR
More informationREAD ME FIRST! IMPORTANT WARNING! ENG. Roof top tent
Roof top tent ENG TENT031 220 min READ ME FIRST! Thank you for purchasing a Front Runner Roof Top Tent. Before you start, take a moment to familiarize yourself with these Fitting Instructions and the components
More informationGoBidet Bidet Attachment
GoBidet Bidet Attachment 151 Ruths Place #5 Sequim, WA 98382 Tel 1-800-681-0753 Fax +1 360-681-4029 www.go-bidet.com MODEL #2003C In this box: 1 User Manual 1 GoBidet Unit w/ mounting bracket, nut, rubber
More informationInstruction Manual Remote Swabbing and Microbiological Sampling and Teflon template tools Version , Rev.0
ASSEMBLY AND OPERATIONAL INSTRUCTIONS The remote swabbing and microbiological sampling tool and the Teflon template tool are shipped partially assembled. Complete assembly instructions are provided below:
More information4-foot Economy Sign Post. 4-foot post is rated at 2 pounds per foot. 7-foot Economy Sign Post
Introduction: ComplianceSigns.com offers a variety of sign posts, sign mounting hardware, sign bases, mounting tape and more to mount your safety signs indoors or out. We offer three styles of sign posts,
More informationInstallation Instructions for Wall Mount, Deck Mount and Pre-rinse Faucets
Installation Instructions for Wall Mount, Deck Mount and Pre-rinse Faucets SAVE FOR END USER ELKAY 2222 CAMDEN COURT OAK BROOK, IL 60523 USA WALL MOUNT ASSEMBLY General Instructions Turn off the water
More informationAdvantage Plus TIM-3600 Series Reel
Read the following precautions and instructions before you begin assembly or using. Failure to comply with these instructions could result in personal injury or property damage. Keep these instructions
More information3300-KIT, ELITE, VALVE SWITCHING PARTS INCLUDED. The Recirculating Freshwater Flush Conversion Kit. Questions, problems, missing parts?
00-KIT, ELITE, VALVE SWITCHING The Recirculating Freshwater Flush Conversion Kit PARTS INCLUDED Questions, problems, missing parts? 0 Sun Dolphin Drive Muskegon, MI 4444 Phone: -0-0 Fax: -- www.fivepeaks.net
More informationTOKISTAR. Exhibitor TOKISTAR LIGHTING
TOKISTAR Exhibitor TOKISTAR LIGHTING Exhibitor TM T okistar Exhibitor Series is a wet-location festoon lighting system used in amusement parks, shopping centers, street decorations and promenades. Exhibitor
More informationDO NOT USE WITH CROSSBAR SPREAD LESS THAN 24.
TM Please read all instructions carefully before assembly, installation and/or use of this product. DO NOT USE WITH CROSSBAR SPREAD LESS THAN 24. WARNING: Do not exceed the weight limit of your vehicle
More informationSteadiCam Parts List*
SteadiCam Parts List* A. 1 Bogen 3232 Monopod Swivel Tilt Head B. 1 1/2 internal to 1/2 external brass bushing flare adapter (part 9402249 at osh.com¹) C. 2 3/8 internal to 1/2 external brass bushing flare
More informationM A N U A L ARCTIC SHELTER LTD. OFFICE WATER ST. VANCOUVER, BC V6B 0M9 CANADA
ARCTIC SHELTER LTD. OFFICE 8098 200-375 WATER ST. VANCOUVER, BC V6B 0M9 CANADA Help Desk: arctic@hdshelter.com 2016 Arctic Shelter Ltd. All Rights Reserved. NOT FOR SALE INSTRUCTION M A N U A L 2016-2017
More informationGlass Door Fittings Glass Door Accessories
Angled striking plate Aluminium stainless steel coloured 981.27.983 Recess striking plate DIN left DIN right Steel nickel plated matt 911.39.285 911.39.28 WC thumbturn cylinder Area of application: For
More informationRhino-Rack SUNSEEKER II Awning 2.0 metres (32109)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationFILTERED FAN PACKAGES
FILTERED FAN PACKAGES PLASTIC & METAL FILTERED FANS EFFICIENT, QUITE BALL BEARING MOTORS NEMA TYPE 1 AND 3R ALL KITS INCLUDE GASKETS, HARDWARE, AND TEMPLATE UL LISTED Plastic FILTER FAN PACKAGES Injection
More informationWIDESPREAD LAVATORY MODELS WITH HI-ARC SPOUT
5951, 5961, 5981, 5983, 5993 SERIES MT122B INSTALLATION INSTRUCTIONS THESE INSTRUCTIONS MUST BE LEFT WITH HOMEOWNER WIDESPREAD LAVATORY MODELS WITH HI-ARC TRADITIONAL CROSS NOTE: Handle Inserts are not
More information1Perma-Shield Gliding Doors (PSI 1968 to 1978)
1Perma-Shield Gliding Doors (PSI 1968 to 1978) Parts Catalog Main Menu Section TOC Search What s in This Section 2-Panel, 3-Panel, and Sidelights...................................... Page 3 Parts Illustration...........................................................
More informationCloset and Specialty Hardware
Closet and Specialty Hardware Door & Mirror Hardware...100 Magnetic and Bullet Catches... 100 Sliding Door Pulls........................................ 100 Mirror Clips/Glass Clips, Fittings and Latches...
More information1Perma-Shield Gliding Doors (PSI 1968 to 1978)
1Perma-Shield Gliding Doors (PSI 1968 to 1978) Parts Catalog Main Menu Section TOC Search What s in This Section 2-Panel, 3-Panel, and Sidelights...................................... Page 3 Parts Illustration...........................................................
More informationTuf-Lite II Fans 7000 Series Hub
Tuf-Lite II Fans Series Hub INSTALLATION MANUAL Hudson Tuf-Lite II fan blades Adjustable Pitch Fan Assembly 34 & 3 Diameter Hudson Tuf-Lite II (white, prev. blue***) fan blades are made from fiberglass
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationTABLE & FURNITURE LEGS
LEGS & LEVELERS TABLE & FURNITURE LEGS Furniture Levelers Furniture levelers from, perfect for entertainment and built-in shelving units. Table Legs The PMI Table Leg line has been very popular for more
More informationTuf-Lite III Fans 4000KW Series Hub
Tuf-Lite III Fans 4000KW Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 11 through 20 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass
More informationTuf-Lite and Tuf-Lite II Fans 6000M Series Hub
Tuf-Lite and Tuf-Lite II Fans 6000M Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 32.8 or 10 Meter Diameter Hudson Tuf-Lite and Tuf-Lite II fan blades Hudson Tuf-Lite (black) fan blades
More informationGround Clamps Cable Tray
COMMERCIAL AND INDUSTRIAL FITTINGS: GROUNDING FITTINGS AND SOLDERLESS CONNECTORS Clamps Cable Tray Terminates ground wire to cable tray. For aluminum or copper conductors. 1 4 hex wrench tightens both
More informationD. S. HULL COMPANY, INC
Perko Flush Ring Pull Chrome plated zinc. Order No Mfg No O.D. List 340427 1232DP1CHR 1-5/8 $15.78 340434 1232DP2CHR 2 $18.38 Perko Flush Lifting Handle Chrome plated brass. Screw size: #8. Note: 776DP2
More informationRUPHIS Blade Clamp. Instruction Manual
RUPHIS Blade Clamp P/N 1006800 NSN 1615-01-562-8156 Instruction Manual AH-64D UH-60A/L UH-60M S-70i S-92 REVISION AUTHORIZATION / RECORD These instructions are primarily for inspection of the RUPHIS Blade
More informationASSEMBLY GUIDE. Customer Service: INCH² 2-BURNER & 864 INCH² 2-BURNER
ASSEMBLY GUIDE 688 INCH² 2-BURNER & 864 INCH² 2-BURNER DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open lid. 4. If odor continues, keep away from the appliance
More informationStandard Awning Installation Instructions
Standard Awning Installation Instructions Important Note: Please become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and will make
More informationThermostatic Griddle Field Service Kit Instructions
Thermostatic Griddle Field Service Kit Instructions The following document provides instructions on how to install a Garland Thermostatic Griddle Field Kit and is applicable to each 2 section of a Garland
More informationTWO PERSON WALL MOUNT
ONE TIER TWO TIER THREE TIER FOUR TIER FIVE TIER SIX TIER 16 PERSON TWO PERSON WALL MOUNT Specifications Body: Entire unit (bottom, sides, top, back, and shelves) constructed of mild cold rolled 24 ga.
More informationJ C / Sunshine Sales, Inc Sales: (800) W. 109th Terr Kansas City, Mo K C : (816) Fax: (816)
Sunshine Tub spouts Mixet Style Diverter Spout Tub Filler Spouts Unique! Mixet Style Diverter Spout 5/8 od Slip Fit Stock # TS132 List Price $ 9.48 1/2 FIP Nose End Stock # TS137 List Price $ 6.68 Pull
More informationPARTS INCLUDED IN YOUR KIT. You may want to lay them out in this manner for accessibility. Foam has NO adhesive to touch truck finish.
INSTALL ATION SHEET Tarp Assembly with Cab Rail, Tail Rail and Support Bows attached. Left and Right Side Rail Assemblies U Clamps (x 6) NOTICE: If your truck has a bedliner that wraps over any top edges,
More informationUrea/Adblue Hose Reel
www.scintex.com.au sales@scintex.com.au Model: SHR3408 Urea/Adblue Hose Reel Product Manual Specifications Spring driven drum: for automatic rewind. Locking ratchet: to maintain the desired length of hose
More information* * 4023 KR. Step 1 Prepare the Keyed Removable Unit. Not for use on electric or fire rated removable mullions
condition. *64009-00* 64009-00 Keyed Removable Mullions 403 KR Installation Instructions Not for use on electric or fire rated removable mullions This kit includes the following parts: (Not to scale) 5/6
More informationAJW. Athletic Series Lockers. Architectural Products ONE TIER TWO TIER THREE TIER FOUR TIER FIVE TIER SIX TIER
ONE TIER TWO TIER THREE TIER FOUR TIER FIVE TIER SIX TIER Specifications Body: Backs constructed of mild cold rolled 18 ga. commercial grade steel. Bottom, sides, top, and shelves constructed of 16 ga.
More informationCloset and Specialty Hardware
Closet and Specialty Hardware Door & Mirror Hardware...100 Magnetic and Bullet Catches... 100 Sliding Door Pulls........................................ 100 Mirror Clips/Glass Clips, Fittings and Latches...
More informationDC 700 Series Hose Reel - September 2010
Instructions Parts List Service Manual DC 700 Series Hose Reel - September 2010 Suitable for dispensing, transfer and evacuation of lubricants, fuels, air & other automotive & industrial products. To be
More informationCarbon Lite Volleyball system ( Either in packages or components ordered separately )
Instruction Manual VB7222 Carbon Lite Volleyball system ( Either in packages or components ordered separately ) Customer Service (800) 247-7668 P A R T S L I S T Item Qty Description Item Qty Description
More informationRhino-Rack SUNSEEKER II Awning (32105)
(32105) Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the
More informationPARTS LIST COLT COLT HEPA
PARTS LIST COLT 800-1250 - 1450 COLT HEPA - 1250-1450 MOTOR / LID ITEM PART NO. PART DESCRIPTION QTY. 101 0891201 TOP COVER 1 102 0294341 TOP MOTOR SEAL 1 103 0299861 STRAIN RELIEF CORD CLAMP 1 104 0891131
More informationLITE Spear Awning Instructions
LITE Spear Awning Instructions IMPORTANT NOTE: Please take a few minutes to become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and
More information* * KR54-F, KR9854 & KR9954 Installation Instructions. Read All Warnings Before Starting Installation! Index:
*941061-00* 941061-00 Keyed Removable Mullion KR54-F, KR9854 & KR9954 Installation Instructions CLASSIFIED CLASSIFIED C Read All Warnings Before Starting Installation! Index: General Information ----------------
More informationRhino-Rack SUNSEEKER II Awning
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationSolar Power Shade INSTRUCTION MANUAL
INSTRUCTION MANUAL 20 June 2006, Revision Initial Release 26 September 2006, version 2 Powerfilm, Inc. 2337 230th Street Ames, IA 50014 (515) 292-7606 Web Site: www.powerfilmsolar.com Table of Contents
More informationDOOR - Single Leaf, Premium Duty, Quick-Acting Model 1430 Features 1
DOOR - Single Leaf, Premium Duty, Quick-Acting Model Features 1 FREEMAN MARINE Quick-Acting doors feature patented chain-drive, single actuation dogging. This design feature allows for quick-acting doors
More informationASSEMBLY & CARE INSTRUCTIONS
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 3 9 Part No. FT3711 - on road FT3923 - off road OPTIONAL SUNROOM Wall and floor kit Part No. FT3723 - on road FT39 - off road OPTIONAL SPARE ROOM Roof,
More information80070 TOP MOUNT CAMPER SHELL and TRANSIT CONNECT RACK TMCS_3:1
ASSEMBLY INSTRUCTIONS for : 80070 TOP MOUNT CAMPER SHELL and TRANSIT CONNECT RACK TMCS_3:1 (916) 638-8703 (800) 343-7486 11261 Trade Center Drive Rancho Cordova, CA 95742 www.kargomaster.com Transit ASSEMBLY
More informationMACHETES & MACHETE SHEATHS HUDSON BAY AXE SINGLE EDGE AXE GUARD DOUBLE EDGE AXE GUARD LADDER PLATFORM. Machete CAT. NO.
Phone: 800-227-4255 www.hallssafety.com Fax: 724-458-0592 MACHETES & MACHETE SHEATHS Machete 2PMA18-18 Blade 2PMA22-22 Blade High quality machete. High carbon tempered steel blade. Black poly handle with
More informationIntegrated Process Solutions
Integrated Process Solutions w w w. m k s i n s t. c o m Series 31 ISO-KF fittings Sizes to 0 ( to 4'') Series 31 is a line of ISO-KF standard vacuum components. The ISO-KF system refers to the family
More informationORDIC FIBERGLASS, INC.
s, 1 Phase Sectionalizing ORDIC FIBERGLASS, INC. 15/25kV 200Amp Single Phase Sectionalizing s Rust free fiberglass construction and stainless steel hardware. The exterior Munsell green coating which contains
More informationASSEMBLY & CARE INSTRUCTIONS. 7 x4 TRAILER TENT SERIES 4 9. OPTIONAL SUNROOM Wall and floor kit. OPTIONAL SPARE ROOM Roof, wall and floor kit
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 9 Part No. TM709 OPTIONAL SUNROOM Wall and floor kit Part No. TM723 OPTIONAL SPARE ROOM Roof, wall and floor kit Part No. TM76 Please keep these instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS KR54, KR1654, & KR4954 Keyed Removable Mullion NOT FOR USE ON ELECTRIC OR FIRE RATED MULLIONS. This kit includes the following parts: (Not to scale) WARNING Remove key, reinstall,
More informationTuf-Lite and Tuf-Lite II Fans 6000 Series Hub
Tuf-Lite and Tuf-Lite II Fans 6000 Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 32 and 33 Diameter Hudson Tuf-Lite and Tuf-Lite II fan blades Hudson Tuf-Lite (black) fan blades are made
More informationAnchor Family Product Manual for the Rifton Anchors
Anchor Family Product Manual for the Rifton Anchors Contents Warnings and important information 3 Check your order 4 Anchors Hand Anchor 4 Wrist Anchor 4 Grab bar 4 Elbow Anchor 5 Horizontal Anchor 5 Arm
More informationRhino-Rack FOXWING Awning by OZTENT
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationAutomated Tiki Torch Installation Instructions
Automated Tiki Torch Installation Instructions Automated Tiki Torch with Poles (Exploded View) 14 Automated Tiki Head 6 8 Tiki Pole (Powder Coated Aluminum or Faux Bamboo Pole) 18 Base Pole (Powder Coated
More informationPN-3, PN-4 Powernode Enclosures
PN-3, PN-4 Powernode Enclosures Addendum to Site Preparation and Installation Manual Effective: March, 2001 200 2 031-103-C1-001 Rev. A 2001 031-103-C1-001 Rev. A March, 2001 2001 Alpha Technologies Introduction
More informationKAWNEER 1786 RIM EXIT DEVICE
FEBRUARY, 2015 1 DOOR STILE Device C L 40" 41-9/32" Cylinder C L Bottom of door RIM EXIT DEVICE LOCATION DOGGING KEY EXIT DEVICE FILLER PLATE CYLINDER & CYLINDER RING HOUSING COVER CYLINDER INSTALLATION
More informationSECTION SPECIFICATIONS PART 1 GENERAL
PART 1 GENERAL 1.1 SECTION INCLUDES A. Shower doors. B. Sliding enclosures. C. Shower doors and panels. 1.2 RELATED SECTIONS A. Section 06100 - Rough Carpentry; blocking. B. Section 15400 - Plumbing Fixtures
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. One-piece connector body: Fastest assembly Field installable Anaerobic epoxy
More informationSeven-eighths-spacing Rackmount Kit/Chassis Rackmount Kit. Techmar enclosure designs include interchangeable modular components,
SRK/CRK SERIES Seven-eighths-spacing Rackmount Kit/Chassis Rackmount Kit Techmar enclosure designs include interchangeable modular components, punched hole patterns and captive hardware, resulting in a
More informationP3000 UNIVERSAL Clamp-On
IHI INSTRUCTION MANUAL Required Tools P3000 UNIVERSAL Clamp-On Wrench Allen Key P3001 65 ENDCAPS P3011 65 BLACK P300 7 ENDCAPS P301 7 WHITE P3003 ENDCAPS P3013 SILVER PART# DESCRIPTION ENDCAPS SIDE SUPPORTS
More informationItem # BJ2PC With 8 Leg Frame, Cover, and Enclosure Kit with Windows Size: 10 8 Wide x 20 Long (Side Height 6 8 ) (Center Peak Height 9 9 )
Item # BJ2PC With 8 Leg Frame, Cover, and Enclosure Kit with Windows Size: 10 8 Wide x 20 Long (Side Height 6 8 ) (Center Peak Height 9 9 ) Powell & Powell Supply Company, L.L.C. Manufactured by: 1730
More informationFEATHER-LITE ROOF TOP TENT SET-UP GUIDE
FEATHER-LITE ROOF TOP TENT SET-UP GUIDE TENT031 INSTALL TIME: 30 minutes 0 GET ORGANIZED you will need: D Your Tent D The Ladder (in a separate box) D A Power Drill w/ Phillips screw bit D A solid, scratch
More informationCREEK COMPANY PONTOONS
CREEK COMPANY PONTOONS ODC Sport XR 1 The ODC Sport XR 1 is an update on our best-selling 8 foot pontoon boat. FRAME Full take down, no-tools-required, heavy-duty black powder coated steel frame with Plastic
More informationREAD AND SAVE THESE INSTRUCTIONS! EasyAwn Spear Awning Installation
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Spear Awning Installation
More informationREAD AND SAVE THESE INSTRUCTIONS! EasyAwn Standard Awning Installation
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Standard Awning Installation
More informationCJ-7 YJ PREPARATION INSTALLING THE WHEEL WELLS. Jeep Wrangler CJ-7/YJ BedRug Interior Installation Instructions
CJ-7 YJ BRCJ76R BRCJ81R REAR KITS: BRYJ87R Jeep Wrangler CJ-7/YJ BedRug Interior Installation Instructions Congratulations on choosing the finest interior flooring kit available for your Jeep. BedRug material
More informationwww Littleton, 9861.horn Titan Park Circle CO etoutdoors.com BEYOND COMPARE
9861 Titan Park Circle Littleton, CO 80125 303.408.0250 www.hornetoutdoors.com BEYOND COMPARE Cargo Bed Rack RZR 2015 RZR-900, 900-S, 900-4 Rack with removable bottom $399.95 Hornet Roof Rack Spare Tire
More informationLockable Fasport. IFP-600 Dimensions Overall Height 9.5" Overall Width 10" Opening Dia. 6.5" Weight 9 lbs. Model
Lockable Fasport IFP-600 Overall Height 9.5" Overall Width 10" Opening Dia. 6.5" Weight 9 lbs Note: Specify glass thickness when ordering. Die cast body and lid. A12 Aluminum body and ASSA deadbolt. Steel
More informationAuxiliary 63.5l Fuel Tank Ford/Mazda Pick-up Truck 2012-Current READ ME! IMPORTANT WARNING!
Auxiliary 63.5l Fuel Tank Ford/Mazda Pick-up Truck 2012-Current ENG FTFM006 90 min READ ME! Thank you for purchasing a Front Runner Ford/Mazda Pick-Up Truck 2012 - Current Fuel Tank. Before you start,
More informationA A A T E C H N O L O G Y
A A A T E C H N O L O G Y & SPECIALTIES CO., INC. H A R D W A R E C A T A L O G TOTAL SOLUTION SERVICE For the Industrial Piping Marketplace 2011 www.aaatech.com 4 0 Y E A R S S E R V I N G I N D U S T
More informationASSEMBLY GUIDE. Customer Service: INCH² 3-BURNER & 545 INCH² 3-BURNER
ASSEMBLY GUIDE 455 INCH² 3-BURNER & 545 INCH² 3-BURNER DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open lid. 4. If odor continues, keep away from the appliance
More informationInstallation Guide Cable
Installation Guide Cable Thank you for selecting a DuctSox System. This guide will be helpful for the installation of a Cable System. Sections of fabric will be labeled, assembled, bagged, and boxed for
More informationAttenda Floor Mount Bed
Attenda Floor Mount Bed ATN101 Bed Deck Width 80" Bed Deck Depth 36" Height 15.5" Overall Width 84" Overall Depth 40" Weight 110-115 lbs solution. Premium Tru material is fully compounded for superior
More informationXENON HELIDECK FLOODLIGHT INDUSTRY USER MANUAL
TEF 9964 XENON HELIDECK FLOODLIGHT INDUSTRY USER MANUAL IMPORTANT Read this instruction carefully before installing the product 996A106032 TUM 1024 REV. E 06.02.14 Tranberg AS P.O. Box 8033 N-4068 Stavanger
More informationCONVEX Awning Instructions
CONVEX Awning Instructions IMPORTANT NOTE: Please take a few minutes to become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and will
More informationStructural Mullion System
Structural Mullion System Installation Instructions DNA Part Number 10300085 This system is designed to allow for larger window combinations. It is not intended to replace structural members in a building.
More informationFormulate Designer Series 10 Backwall - Kit 01
Formulate Designer Series 10 Backwall - Kit 01 FMLT-DS-10-01 Formulate TM Designer Series 10ft displays have unique stylistic features and shapes, are portable and easy to assemble. The aluminum tube frame
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS FRONT TIEDOWNS CHAIN AND CLEVIS REMOVED
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C2205/FMTPJ01NDCHSB FRONT TIEDOWNS CHAIN AND CLEVIS REMOVED 07.06.2011 Minor movement (or settling) can occur in some incidental harsh driving conditions
More informationCloset and Specialty Hardware
Closet and Specialty Hardware Door & Mirror Hardware...108 Magnetic and Bullet Catches... 108 Sliding Door Pulls........................................ 108 Mirror Clips/Glass Clips, Fittings and Latches...
More information1946 READ AND SAVE THESE INSTRUCTIONS!
EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Quarter Round Awning Installation
More informationThe Lock People SERVING INDUSTRY SINCE 1971
1-800-854-3565 U.S. Patent#: 4,694,667. Made in USA. Copyright 2006, Hodge Products, Inc. www.lockpeople.com The Lock People SERVING INDUSTRY SINCE 1971 page 2 Suggested Uses Fences & Gates All Types of
More informationOPERATOR INSTRUCTION MANUAL INCLUDING REPAIR PARTS FOR MODULAR GENERAL PURPOSE TENT SYSTEM (MGPTS) TYPE I
OPERATOR INSTRUCTION MANUAL INCLUDING REPAIR PARTS FOR MODULAR GENERAL PURPOSE TENT SYSTEM (MGPTS) TYPE I Johnson Outdoors Gear, Inc. Eureka! branded tent products 625 Conklin Road Binghamton, NY 13903
More informationAssembly TOOLS REQUIRED: 17mm and 14mm or equivalent wrenches.
Instructions for 3 Trimmer Rack, 3TR* *Patents Pending Assembly TOOLS REQUIRED: 17mm and mm or equivalent wrenches. 15 26 26 16 15 16 Attach the lower mounting brackets to the Trimmer Rack poles as shown
More informationPARTS INCLUDED IN YOUR KIT. You may want to lay them out in this manner for accessibility. Foam has NO adhesive to touch truck finish.
-'07 Ford Sport Trac Tarp Assembly with Cab Rail, Tail Rail and Support Bows attached. Left and Right Side Rail Assemblies Sport Trac Brackets (x4) Clamp Bolts Allen Wrench PARTS INCLUDED IN YOUR KIT.
More informationWater Trailer Series. WT5HR Hose Reel Kit Installation REQUIRED TOOLS PARTS WORK SAFELY! PREPARATION
Water Trailer Series WT5HR Hose Reel Kit Installation The following instructions are intended to assist the user in the installation of the WT5HR Hose Reel Kit for use on the WT5C, WTE5C, WT5CSG Series
More informationFLEX KEY ASSEMBLY. ..._ o RAFTER ARM TUBE MAIN ARM TUBE CAP NUT CLAW HINGE
ZIP DEE Inc. 96 Crossen Ave. Elk Grove Village, IL 60007(847)437-0980 (800)338-2378 HEAD CASTING AWNING RAIL FLEX KEY ASSEMBLY..._ o GM1 Installation Instruction GMC Motorhome RAFTER ARM TUBE MAIN ARM
More informationYAMAHA WINCH MOUNT KIT. Installation Instructions KIT NUMBER:
YAMAHA WINCH MOUNT KIT Installation Instructions KIT NUMBER: 25-5160 CUSTOMER MUST RECEIVE A COPY OF THIS INSTRUCTION MANUAL AT TIME OF SALE 2005 CYCLE COUNTRY ACCESSORIES CORP. Rev. 2 9/22/06 Please Note:
More informationPARTS LIST CHARGER 2022 ABLT
PARTS LIST CHARGER 2022 ABLT HEAD ASSEMBLY ITEM PART NO. DESCRIPTION QTY 101 5990731 SPRING CLIP PAD HOLDER SET INCLUDES: 1 101A 9120205 #8 X 1/2 PAN HEAD PHILLIPS SHEET METAL SCREW PACK OF 3 3 102 9121490
More informationAutomated Tiki Torch Installation Instructions
Automated Tiki Torch Installation Instructions Automated Tiki Torch with Poles (Exploded View) 14 Automated Tiki Head 6 8 Tiki Pole (Powder Coated Aluminum or Faux Bamboo Pole) 12 Base Pole (Powder Coated
More informationFactory Style Bow Kit
Installation Instructions Factory Style Bow Kit Vehicle Application: Jeep Wrangler Unlimited 2004 2006 Part Number: 55003 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question.
More informationY Camper Shell Tracks, 37 Cross Bars. Y Camper Shell Tracks, 44 Cross Bars.
Y06-550 63 Camper Shell Tracks, 37 Cross Bars. Y06-560 63 Camper Shell Tracks, 44 Cross Bars. Important: Parts List Please read these instructions carefully prior to installation. Please refer to your
More informationTools. For safety and easy faucet replacement, San-Ei recommends the use of the following helpful tools:
BW-0BH INSTALLATION INSTRUCTIONS SINGLE HANDLE Kitchen Faucet Tools For safety and easy faucet replacement, San-Ei recommends the use of the following helpful tools: SAFETY GLASSES PIPE WRENCH PLIERS CHANNEL
More informationMotorized Oasis Awning RTS Motor Cord Replacement Instructions *Helpers Needed*
RETRACTABLE AWNINGS For Technical Support visit us at www.sunsetter.com/ownerscorner or Call Toll Free 800-670-7071 Fax 877-224-4944 Motorized Oasis Awning RTS Motor Cord Replacement Instructions *Helpers
More informationV O X POP MARKETING SYSTEMS
Exterior Merchandising R Solutions for Checkers & Rally s R 2018 Product & Price Guide 1-800-386-9767 Fax: 410-641-1092 Int l 410-641-1090 Berlin, MD www.voxpopms.com TopLine Banner Frame Rooftop Banner
More information3/8 X 1-7/8 Washer /8-16 Serrated Flange Nut
Mystic II Round Part # 420916-10 Round Packing List ITEM DESCRIPTION PART # 8 21 24 27 30 33 Carton # 1 Carton # 2 Carton # 3 8 x52 Gray Forest 1742 1 - - - - - - - - x52 Gray Forest 1743-1 - - - - - -
More informationINSTALLATION INSTRUCTIONS AND OWNER'S MANUAL AWNINGS. For trailers & motor homes with straight sides TOOLS REQUIRED
AWNINGS INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL For trailers & motor homes with straight sides TOOLS REQUIRED 1/4" electric drill Ratchet handle kit 3/8" & 7/16" socket No. 1 and No. 2 screwdriver
More information