IVT Guide and Marker. Ø 7.0mm Pad with 3.5mm Guide and 4.0mm guide, 45 angled shafts, total length 140mm

Transcription

1 IVT Guide and Marker H-2004 IVT Guide Pad, Double Ended, 3.5 / 4.0mm Ø 7.0mm Pad with 3.5mm Guide and 4.0mm guide, 45 angled shafts, total length 140mm H-2670A IVT Marker, pointed 4.0 mm and 3.5 mm, Stainless Steel

2 LASIK Fixation Ring H-7200 Krumeich LASIK-Suction-Ring Outer Diameter: 18 mm Inner Diameter: 11 mm Marking on 0, 90, 180 and 270 LASIK-Suction-Ring to avoid aberrations The appearance of higher-order aberrations (HOA) seems to be a common and not avoidable and unwanted result during LASIK procedures. The induction of such, not previously detectable HOAs, does not dependent on whether a mechanical microkeratome or Femto - laser was used to cut the flap. It accrues by using Excimer-lasers with 200 Hz, as well as with the latest models of Hz. HOAs appear when saccades of spontaneous rapid eye movements are reported during the operation. These movements should be compensated by the Tracker, but according to several tests of Dr. Krumeich, the only reliable method to avoid HOIs is a mechanical fixation of the eye. The fixation with the Krumeich suction ring does not increase the intraocular pressure. In this respect, also the blood supply is not stopped or a Venous Stasis is not caused. A fixation ring which is built according to the principle of the Barraquer increases intraocular pressure to approximately 60 mmhg and stops the blood flow for the time of the intake. Such a ring is not suitable for fixation. The Krumeich Suction Ring has a inner diameter of 11 mm, so that it doesn't bother the trace of the laser. The ring is placed after creating the flap and manually fixed with vacuum of mbar.

3 Instruments for Capsulorrhexis H-2651 H-2652 Capsulorrhexis Marker 6.0 mm diameter marking ring with 2.5mm extensions for alignment with the limbus, Stainless Steel Capsulorrhexis Marker 5.5 mm diameter marking ring with 2.5mm extensions for alignment with the limbus, Stainless Steel H-6087 H-6087G vaulted long shanks, 6 mm round handle, stainless steel vaulted long shanks, with 1 mm graduation, 6 mm round handle, stainless steel H-6088 H-6088G vaulted long shanks, 8 mm round handle, stainless steel vaulted long shanks, with 1 mm graduation, 8 mm round handle, stainless steel

4 IOL Explantation through small incisions H-4294 H-4295 IOL scissors Grooves on the lower cutting blade guarantees no sliding effect while cutting the lens Secure cutting thanks to strong and sharp blades Blade length: 8 mm Diameter in the joint: 1.8 m H-6038 IOL Grasping Forceps Secure holding of the lens and the fragments during cutting it inside the capsule sac Fragments can be easily removed thanks to the special strong teeth at distaltip of the jaws Jaw length: 11 mm Diameter in the joint: 1.2 mm

5 Phaco Choppers H-1938 Davidoff Ambidextrous Nucleus Chopper, Stainless Steel H-1939A H-1939B Tomahawk Nucleus Chopper, Right Hand Dominant, Stainless Steel Tomahawk Nucleus Chopper, Left Hand Dominant, Stainless Steel H-1943 Minardi Phaco Chopper, short (0.75mm) pointed "quick chop" tip, Stainless Steel

6 Iridectomy Forceps H-6324 Iridectomy forceps 20 Ga. 1x2 straight teeth, vertical opening of the jaws Scleral Shield Scleral shield non-reflective exterior surface, stainless steel To protect the eye during blepharoplasty and skin resurfacing procedures. H-2940 H x 28mm, small (pair) 22 x 30mm, large (pair)

7 Needle Holders H-4555A H-4555B Micro-Needle Holder, extra delicate jaws, curved, without lock, Stainless Steel Micro-Needle Holder, extra delicate jaws, curved, with lock, Stainless Steel