CIRRUS AIRPLANE MAINTENANCE MANUAL

Size: px
Start display at page:

Download "CIRRUS AIRPLANE MAINTENANCE MANUAL"

Transcription

1 CABIN 1. GENERAL The aft passenger windows are manufactured of acrylic and adhesive bonded to the fuselage. Replacement is accomplished by removing the interior trim around the window, removing the sealant around the window, and then removing the window from the fuselage. In general, the reverse process is used to install a replacement window. This method is literally seamless, and the fuselage will show no marks or evidence of maintenance. Page 1

2 2. MAINTENANCE PRACTICES A. Aft Passenger Window (1) Removal - Aft Passenger Window (See Figure 1) (a) Acquire necessary tools, equipment, and supplies. Description P/N or Spec. Supplier Purpose Die Grinder (1-Inch Cut-Off Disk) - Any Source Cut window. Masking Tape 2-inch Any Source Prevent damage to the window. Drop Cloth - Any Source Prevent contamination. Isopropyl Alcohol 99% or higher purity Any Source General cleaning. Aluminum Oxide Sandpaper Phenolic or Hardwood Utility Knife 80-grit Any Source Sealant removal. 1-inch Any Source Sealant removal. (b) Remove the interior trim panels from around the window. (Refer to 25-10) (c) Cover the interior and instrument panel with a drop cloth to prevent foreign material from contaminating the interior and instruments. (d) Using several pieces of duct tape, make handles on the exterior of the window. Exercise care to prevent the removal of laminate from the fuselage when cutting and removing the sealant from between the fuselage and window. If laminate is damaged, it must be repaired prior to installing the window. If window is being replaced, it will be easier to use a die grinder and a cutoff disk to cut out the inner portion of the window to gain access to the bonding flange. The window should be cut as close as possible to the fuselage. (e) (f) Cut sealant loose from between fuselage and window using a small pocket knife. While pushing in on the window, follow the edge of the fuselage with the tip of the blade, then back cut in towards the fuselage to clean out the sealant. (See Figure 1) Using a phenolic or hardwood utility knife, isopropyl alcohol and aluminum oxide sandpaper (80-grit), remove all remaining sealant from the fuselage bonding flange. Page 2

3 BONDING FLANGE Cut window out next to bonding flange, do not damage laminate. Any laminate which becomes damaged must be repaired prior to inatalling the new window. WINDOW BONDING FLANGE SEALANT Push window inward while cutting sealant between bonding flanges. FUSELAGE BONDING FLANGE FUSELAGE (REF) SECTION SR20_MM56_4350 Figure 1 Window Removal Page 3

4 (2) Installation - Aft Passenger Window (See Figure 2) (See Figure 3) Window sealant is intended to provide an acceptable seal between the window and fuselage and to prevent the leakage of air through the airframe structure. Window sealant is used in the installation of all windows in the aircraft. Isopropyl alcohol, kerosene, white alptha naptha, mineral spirits, and cotton are acceptable for cleaning acrylic windows. Residue left behind by the Spraylat protective coating may be removed by soaking the area with isopropyl alcohol and rubbing with an alcohol soaked soft flannel cloth. Residue left behind by the adhesive backed paper covering can also be removed by the above method. If, however, the paper covering has been stored on the window for an extended period of time, soak paper with kerosene and keep it wet for several hours. Remove any remaining adhesive by using a mixture of equal parts of kerosene and isopropyl alcohol. Soak a soft flannel cloth with this mixture and rub the window with the cloth. The window should be cleaned after this procedure with a dish washing liquid and plenty of water. WARNING: Never use organic solvents such as Methyl Ethylketone (MEK), acetone, or lacquer thinner. Do not use jewelry cleaner or paper towels to remove any contaminates. Never use ice scrapers on acrylic windows. Do not store any window outdoors while the protective covering is still on the window. The covering will become very difficult, if not impossible, to remove without damaging the window. It is very important to keep the window well supported at all times. Warm temperatures are not required during these operations; however, acrylic will take much more abuse at 80 degrees than at 30 degrees. Always inspect the window before final installation. Use care to prevent staining or scratching the window. (a) Acquire necessary tools, equipment, and supplies. Description P/N or Spec. Supplier Purpose Padded Cargo Rods - Any Source Temporarily secure window. Masking Tape 2-inch Any Source Prevent damage to the window. Temperature-Resistant Sealing Compound MIL-S-8802 Type II, Class B (Refer to 20-10) Seal windows. Isopropyl Alcohol 99% or higher purity Any Source General cleaning. Cotton Gloves (clean, lint free) Cotton Cloth (clean, lint free) Application Spatula (nonnylon) - Any Source Protect hands. - Any Source Clean sealing surface. 1-inch Any Source Smooth adhesive. Page 4 Primer MC-145 LP Aero Plastics Aid in adhesion.

5 Description P/N or Spec. Supplier Purpose Protective Coating AC-940 Blue AC Products, Inc. Prevent damage to the window. Fine Line Tape (pin stripping) Sandpaper, Aluminum Oxide 1/4-inch 3M Company ow smooth transition between fuselage and window. 80-grit or finer Any Source Abrade acrylic surface prior to adhesion. Exercise care to protect the inner and outer window surfaces from damage during the installation process. The stepped area on the edge of the window (which is bonded to the fuselage) is called the bonding flange. (b) (c) (d) (e) Verify that sealant is within storage-life requirements. Inspect fuselage bonding flange for any remaining sealant or contaminates, remove and clean as necessary. Remove the protective covering from the window and inspect the window for damage or defects, never install a defective window. Install a continuous piece of fine line tape on the edge of the fuselage window opening (next to the bonding flange). (See Figure 2) The masking tape will provide a smooth and continuous parting line at the bonding flange. (f) (g) Working in one direction on the fuselage window opening, place 2-inch masking tape on top of the outer edge (the edge furthest away from the bonding flange) of the fine line tape. Make a directional mark on the masking tape to indicate the proper direction for removal. (See Figure 3) Do not apply protective coating on the window bonding flange. (h) (i) Apply three coats (in opposing directions) of protective coating (AC-940 Blue) on the outer window surface. Using several pieces of duct tape, make handles on the exterior of the window after the protective coating has fully cured. Five or more padded cargo rods may be necessary to hold the window into the proper position. Padded cargo rods may be placed on each corner of the window and in the center of the window. Additional padded cargo rods may be required to prevent the window from sliding down. (j) (k) Place window into position and secure the window into the fuselage using padded cargo rods. (See Figure 3) Inspect the window for proper fit. The window must have equal amounts of space around the perimeter of the window. The exterior surface of the window should be flush with exterior surface of fuselage. Page 5

6 The window bonding flange must never be trimmed to a thickness less than of an inch. The window bonding flange must never be less than ½- inch wide. The window bonding flange should have equal amounts of space around it. If the window doesn t fit into the fuselage with equal amounts of space around it, the window and/or bonding flange will need to be trimmed accordingly. The window should be flush with the exterior surface of the fuselage. If the window cannot be made flush by adding moderate pressure on the cargo rods, the thickness of the window bonding flange must be trimmed accordingly. Aluminum oxide sandpaper (80-grit) on a sanding board may be used to trim the window. (l) Mark and trim the window as required to ensure a perfect fit. Five or more padded cargo rods may be necessary to hold the window into the proper position. Padded cargo rods may be placed on each corner of the window and in the center of the window. Additional padded cargo rods may be required to prevent the window from sliding down. (m) Place the prefit window into position and clamp the window into position using padded cargo rods. Page 6

7 BONDING FLANGE HANDLE Trim window as required to ensure equal spacing on all sides NOTE Placement of padded cargo rods. Trim window thickness as required to obtain a flush fit to fuselage. Trim window bonding flange as required to obtain a 0.5 inch flange. Apply protective coating on window to prevent damaging window during the installation process " MINIMUM WINDOW BONDING FLANGE 0.5" MINIMUM FUSELAGE (REF) SECTION Figure 2 Window Alignment SR20_MM56_4351 Page 7

8 (n) (o) (p) Remove a small amount (approximately 2-inches wide) of protective coating from around edge of window. Install a continuous piece of fine line tape (pinstripe tape) around the edge of the window (next to the bonding flange). The fine line tape should be adhered to the window with equal amounts of space between the fine line tape on the fuselage and the fine line tape on the window. Working in one direction on the window, place 2-inch masking tape on top of the inner edge (the edge furthest away from the bonding flange) of the fine line tape. The alignment marks will be used to ensure that the window will be installed into the exact location in which it was during prefit. (q) (r) (s) Using a straight edge, make several alignment marks around the edges of the masking tape on the fuselage to the masking tape on the window. Carefully remove window from fuselage. Using aluminum oxide 80-grit paper, abrade the bonding flange of the window in a random pattern. Remove all surface gloss. Wax or grease pencil markings on any part are not allowed. Any such markings inadvertently occurring must be removed prior to application of primer. surfaces shall be thoroughly cleaned and dried before application of primer. Immediately prior to applying any primer on the window bonding flange, solvent clean the flange with isopropyl alcohol. When handling cleaned surfaces, wear clean cotton gloves to prevent surface contamination. Surfaces must be re-cleaned in the event of contamination. Fold cloth in such a manner to eliminate raw edges to reduce the possibility of lint. Always clean an area larger than the application area. (t) Remove contaminates from the window bonding flange and the immediate work area using a vacuum and a clean brush attachment. Do not apply primer to the composite bonding surface. (u) Ensure that all surfaces adjacent to the window bonding flange are masked to prevent them from coming into contact with any primer or sealant. (v) Using isopropyl alcohol, solvent clean fuselage bonding flange. (Refer to 20-30) (w) Verify all required materials are present and all parts have been prepared and pre-fit. (x) Wearing clean gloves, lightly dampen a cloth with primer. Fold the cloth in such a manner to eliminate raw edges to reduce the possibility of lint. (y) Apply primer to the acrylic bonding flange. Wipe the cloth over the prepared area. Apply as little primer as possible while still wetting the entire surface. Keep primed area clean and free from contaminates while primer is drying. Seal window as soon as practical after primer drying period to minimize contamination. (z) (aa) ow the primer to dry for thirty to sixty minutes. Mix sealant per manufacturer's instructions. Mix the required quantity in the ratio specified in the adhesive manufacturer's instructions. (Refer to 20-10) Page 8

9 Do not apply sealant to window bonding flange. The sealant must be applied to the fuselage bonding flange. (ab) Apply a thin layer of sealant to the outer edge of the fuselage bonding flange. Spread the sealant out using an application spatula. (Refer to 20-10) When spreading the sealant, ensure all air pockets are removed. If more than one bead is required, apply it immediately adjacent to the prior bead to form one large bead. (ac) Directly on top of the sealant previously spread, apply a 1/4-inch to 3/8-inch bead of sealant down the center of the bond area. (Refer to 20-10) Five or more padded cargo rods may be necessary to hold the window into the proper position. Padded cargo rods may be placed on each corner of the window and in the center of the window. Additional padded cargo rods may be required to prevent the window from sliding down. (ad) (ae) Using padded cargo rods, secure the window into position making sure the reference marks made earlier are perfectly aligned and that the contour of the window matches the contour of the fuselage. Using a 1-inch application spatula, push sealant into the gap between the window and the fuselage. (Refer to 20-10) To prevent sealant from becoming damaged, pull tape towards sealant while the sealant is still damp. (af) Remove masking tape and fine line tape from the perimeter of the window and the fuselage. Overheating windshield can cause window damage. (ag) ow the sealant to air dry. Following the manufacturer s instructions, the sealant can be heat cured using a heat gun. (ah) Remove cargo rods. (ai) Remove the drop cloth. (aj) Using a vacuum cleaner, remove all debris. (ak) Install and secure interior trim panels. (Refer to 25-10) (al) Clean window. (Refer to 56-10) Page 9

10 WINDOW BONDING FLANGE SEALANT FUSELAGE (REF) SECTION FINE LINE TAPE 2" MASKING TAPE SEALANT FUSELAGE WINDOW OPENING FINE LINE TAPE 2" MASKING TAPE DIRECTIONAL ARROW WINDOW BONDING FLANGE HANDLE Trim window as required to ensure equal spacing on all sides NOTE Remove approximately 2-inches of protective coating. Make alignment marks to ensure proper alignment after fit up. Remove surface gloss from bonding flange using 80-grit sandpaper. Force the sealant into the bonding flange to ensure no air is trapped in the sealant. SR20_MM56_4352 Page 10 Figure 3 Window Installation

CIRRUS AIRPLANE MAINTENANCE MANUAL MODELS SR22 AND SR22T CHAPTER 56-20: CABIN GENERAL. Cabin 56-20: CABIN. 1. General

CIRRUS AIRPLANE MAINTENANCE MANUAL MODELS SR22 AND SR22T CHAPTER 56-20: CABIN GENERAL. Cabin 56-20: CABIN. 1. General CIRRUS AIRPLANE MAINTENANCE MANUAL Cabin CHAPTER 56-20: CABIN GENERAL 56-20: CABIN 1. General The aft passenger windows are manufactured of acrylic and adhesive bonded to the fuselage. Replacement is accomplished

More information

Baggage Door. 1. General

Baggage Door. 1. General CIRRUS AIRPLANE MAINTENANCE MANUAL Baggage Door CHAPTER 52-30: BAGGAGE DOOR GENERAL 52-30: BAGGAGE DOOR 1. General The baggage door is located on the left side of the fuselage, just aft of the wing. This

More information

3M Wind Protection Tape 2.0 Application Instructions W8750, W8780

3M Wind Protection Tape 2.0 Application Instructions W8750, W8780 3M Wind Protection Tape 2.0 Application Instructions W8750, W8780 April 2017 Technical Data Note: The following technical information and data should be considered representative or typical only and should

More information

Model 205 Fireview Maintenance Kit

Model 205 Fireview Maintenance Kit Model 205 Fireview Maintenance Kit Please read all of the instructions before you begin the procedure. Confirm that you have all the necessary tools and parts required. Allow about one hour to complete

More information

Chinastars Reflective Heat Transfer Film

Chinastars Reflective Heat Transfer Film Chinastars Reflective Heat DESCRIPTION Chinastars reflective heat transfer film is composed of micro glass beads bonded to a heat activated adhesives, with a transparent PVC liner to protect the reflective

More information

250 SERIES 1" STRUCTURAL TUBE MULLION ASSEMBLY INSTRUCTIONS

250 SERIES 1 STRUCTURAL TUBE MULLION ASSEMBLY INSTRUCTIONS 2014 Pella Corporation Part Number: V985711 250 SERIES 1" STRUCTURAL TUBE MULLION ASSEMBLY INSTRUCTIONS Be sure to thoroughly read and understand all the steps before beginning the mullion assembly process.

More information

Applications Engineering Notes

Applications Engineering Notes Applications Engineering Notes Document Title Document Number MTP Brand Connector Installation Onto AEN-1401 Revision Number 2.1 Effective Date November 15, 2011 THE USE OF SAFETY GLASSES FOR EYE PROTECTION

More information

TAKE EVERY PRECAUTION TO PREVENT CONTACT WITH SKIN OR HAIR!!!

TAKE EVERY PRECAUTION TO PREVENT CONTACT WITH SKIN OR HAIR!!! Rev. 1 Rev. Date 5/31/2018 Seat Insert Instructions _ You have purchased the safest and easiest to use seat insert kit available. Please read these instructions and review the images carefully before starting

More information

WARNING: IMPROPER INSTALLATION WILL RESULT IN LINER FLYING OUT OF THE TRUCK. FOLLOW INSTRUCTIONS EXACTLY

WARNING: IMPROPER INSTALLATION WILL RESULT IN LINER FLYING OUT OF THE TRUCK. FOLLOW INSTRUCTIONS EXACTLY Preparation Instructions Part Number(s): Multiple Kit Contents Item # Qty Req'd Description 1 1 BedTred Floor Panel 2 1 BedTred Bulkhead Panel 3 2 BedTred Sidewall Panels (L&R) 4 1 BedTred Tailgate Panel

More information

JOINING MULLION (DIRECT MULL) ASSEMBLY INSTRUCTIONS FOR 3-WAY OR 4-WAY JOINTS FOR IMPERVIA AWNING, CASEMENT AND LARGE AWNING

JOINING MULLION (DIRECT MULL) ASSEMBLY INSTRUCTIONS FOR 3-WAY OR 4-WAY JOINTS FOR IMPERVIA AWNING, CASEMENT AND LARGE AWNING 2014 Pella Corporation JOINING MULLION (DIRECT MULL) ASSEMBLY INSTRUCTIONS FOR 3-WAY OR 4-WAY JOINTS FOR IMPERVIA AWNING, CASEMENT AND LARGE AWNING For Additional Mullion Assembly Information; Visit www.installpella.com/mullions,

More information

Applications Engineering Notes

Applications Engineering Notes Applications Engineering Notes Document Title Document Number MTP Brand Connector Installation Onto AEN-1420 Revision Number 1.1 Effective Date January 17, 2017 THE USE OF SAFETY GLASSES FOR EYE PROTECTION

More information

Suggested Installation Instructions for: , Embroidered Front End Mask

Suggested Installation Instructions for: , Embroidered Front End Mask I I 1 Suggested Installation Instructions for: 602-246, 1975-1979 Embroidered Front End Mask 2-Cover Hooks 4-Air Foil Inserts 2-2" "U" Shaped Trim Locks 4-2" ADHESIVE BACKED Hook Strips 2-14" ADHESIVE

More information

Applications Engineering Notes

Applications Engineering Notes Applications Engineering Notes Document Title Document Number MTP Brand Connector Installation Onto 3.0 mm Jacketed Round Cable With Loose Fibers AEN-1407 Revision Number 2.1 Effective Date November 15,

More information

Series 2050 Garden Window Frequently Asked Questions

Series 2050 Garden Window Frequently Asked Questions 1. What is the difference between new construction and retrofit? The difference is in the overall jamb depth and required components: For new construction, the flash flange on the head of the unit is left

More information

Instructions. Fibrlok TM 2670 Multi-Fiber Ribbon Construction Tool. November, B

Instructions. Fibrlok TM 2670 Multi-Fiber Ribbon Construction Tool. November, B Instructions Fibrlok TM 2670 Multi-Fiber Ribbon Construction Tool November, 1998 34-7032-7181-6-B Contents: 1.0 General... 3 2.0 Ribbon Construction Tool Kit...3 3.0 Preparing the Fibers...3 4.0 Arranging

More information

SB3T. Roll-InBuddy + Tilt. Dignity + Ease + Comfort. Product features include:

SB3T. Roll-InBuddy + Tilt. Dignity + Ease + Comfort. Product features include: SB3T Roll-InBuddy + Tilt The revolutionary tilt option incorporated into the Roll-InBuddy Tilt allows for pressure release as well as a more thorough bathing experience for the user and easier reach for

More information

FISH CAT SCOUT OWNER S MANUAL

FISH CAT SCOUT OWNER S MANUAL FISH CAT SCOUT OWNER S MANUAL ALWAYS WEAR A COAST GUARD APPROVED FLOTATION DEVICE WHEN OPERATING THE FISH CAT SCOUT. Know the limits of your abilities and the limits of your equipment. Changes in air temperature

More information

Super Fat Cat-LCS ASSEMBLY INSTRUCTIONS AND OWNER S MANUAL

Super Fat Cat-LCS ASSEMBLY INSTRUCTIONS AND OWNER S MANUAL Super Fat Cat-LCS ASSEMBLY INSTRUCTIONS AND OWNER S MANUAL This owner s manual will help you with initial set up of your new float tube, provide basic safety information, review boat maintenance tips,

More information

3 Nomad Scraper Matting 9100 (formerly 3M Entrap Recessed Well Matting)

3 Nomad Scraper Matting 9100 (formerly 3M Entrap Recessed Well Matting) 3 Nomad Scraper Matting 9100 (formerly 3M Entrap Recessed Well Matting) Technical Data/ Product Specifications 1.0 Product Description The product is a durable, all-vinyl floor mat having an open, continuously

More information

Operating Instructions

Operating Instructions Operating Instructions High Throughput Dialysis MODEL HTD96b www.htdialysis.com HTD96b : Operating Instructions Components Universal Base Unit Teflon block assembly: 9 Teflon bars, labeled sequentially

More information

Written By: Sam Lionheart

Written By: Sam Lionheart ipad Air Wi-Fi LCD Replacement Use this guide to replace the LCD screen in your ipad Air. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 27 INTRODUCTION Replace a damaged or nonfunctioning

More information

INSTALLATION INSTRUCTIONS FOR BALCO, INC. FLOOR MATS FM2R-(A, C, D) W/O FRAME 4V

INSTALLATION INSTRUCTIONS FOR BALCO, INC. FLOOR MATS FM2R-(A, C, D) W/O FRAME 4V 2626 South Sheridan PO Box 17249 Wichita, Kansas 67217 Phone: (316) 945-9328 Fax: (316) 945-0789 INSTALLATION INSTRUCTIONS FOR BALCO, INC. FLOOR MATS FM2R-(A, C, D) W/O FRAME 4V 2012, Balco, Inc. INSTALLATION

More information

Termination Procedure LC 1.6mm & 2.0mm Connectors: 1060XX Series

Termination Procedure LC 1.6mm & 2.0mm Connectors: 1060XX Series Connector Piece Parts LC Simplex Connector Boot LC Duplex Connector LC Connector CriMp Tulolng LC Duplex Clip Boot 86001-0110, Rev. B USN30MFO/5/2010 Procedure Chart Procedure Tool Required Tool Part Number

More information

BRJK11F2, BTJK11F2, BRJK07F2, BTJK07F2, kit

BRJK11F2, BTJK11F2, BRJK07F2, BTJK07F2, kit BRJK11F2, BTJK11F2, BRJK07F2, BTJK07F2, FRONT KITS: BRJK07F4, BTJK07F4 Jeep Wrangler JK BedRug/BedTred Interior Installation Instructions Congratulations on choosing the finest interior flooring kit available

More information

Header Bikini Installation Instructions

Header Bikini Installation Instructions Header Bikini Installation Instructions For: Jeep Wrangler 1997-2002 Part Number: 52525 with or without Soundbar with or without Door Surround DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER THAN THOSE

More information

SYSTIMAX RoloSplice Multiple Splice Organizer Installation

SYSTIMAX RoloSplice Multiple Splice Organizer Installation SYSTIMAX RoloSplice Multiple Splice Organizer Installation General This instruction sheet provides procedures for installing the SYSTIMAX RoloSplice, multiple splice organizer management system and is

More information

Accu-Chart TM Healthcare Systems, Inc.

Accu-Chart TM Healthcare Systems, Inc. Accu-Chart TM Healthcare Systems, Inc. Training Guide for DeBlister-RX 1305 Remington Rd., Suite I Schaumburg, IL 60173 847-252-7183 Fax: 630-307-5982 techsupport@accuchart.com Accu-Chart TM Healthcare

More information

1 Pan - 6 Ways to Cook! Works in the Oven & On All Stovetops! electric gas ceramic induction. Broil Bake Sauté Fry Steam Braise

1 Pan - 6 Ways to Cook! Works in the Oven & On All Stovetops! electric gas ceramic induction. Broil Bake Sauté Fry Steam Braise *only use non-metal utensils 1 Pan - 6 Ways to Cook! Broil Bake Sauté Fry Steam Braise Non-stick Cerami-Tech Ceramic Coating Even Heating Good for All Surfaces Easy Cleaning Durable, Stain Resistant Coating

More information

International Scout 80/800

International Scout 80/800 International Scout 80/800 Tools needed: sockets wrenches powered drill #2 phillips bit for drill #3 phillips bit for drill or screwdriver tape measure Contents: 2- bedrails, (2 pieces each) 4- bedrail

More information

INSTALL INSTRUCTIONS for VEHICLES

INSTALL INSTRUCTIONS for VEHICLES INSTALL INSTRUCTIONS for VEHICLES Issued: 1 st December 2011 These are the recommended steps for installing One Way Vision (OWV) film onto a vehicle rear windscreen or side glass panels. Location: Applicable

More information

Assembly instructions of an entry boot for fiberglass tanks. Model SEBEF-SEBEFM INSTALLATION TOOLS SHOWN ON PAGE VIII

Assembly instructions of an entry boot for fiberglass tanks. Model SEBEF-SEBEFM INSTALLATION TOOLS SHOWN ON PAGE VIII Assembly instructions of an entry boot for fiberglass tanks Model SEBEF-SEBEFM INSTALLATION TOOLS SHOWN ON PAGE VIII Fig.1 Assemble the mandrel (Model SMAN) and the hole saw (Model STAZ) and insert them

More information

Mini-Condor. Mini-Condor. (Competition Boost Glider for 1/2A & A motors) Shock Cord Anchor Pattern. Kit # Skill Level 3: Average Skills Needed

Mini-Condor. Mini-Condor. (Competition Boost Glider for 1/2A & A motors) Shock Cord Anchor Pattern. Kit # Skill Level 3: Average Skills Needed Mini-Condor Kit #05008 Mini-Condor (Competition Boost Glider for 1/2A & A motors) P/N Description Qty 10058 AT-13/9.0 Body Tube 1 13020 CR 10-13 Green Engine Block 1 13051 1/8 Launch Lug 1 Long 1 15578

More information

FEATURES & BENEFITS OF THE TOW PRO ELITE :

FEATURES & BENEFITS OF THE TOW PRO ELITE : To Protect & Preserve PRODUCT MANUAL & FITTING GUIDE tow pro elite TYPE: TAILORED FIT EACH TOW PRO ELITE COMES WITH THE FOLLOWING: 8mm thick body armour material QUICK ZIP SYSTEM to aid fitting 2 CLEAR

More information

STEALTH PRO OWNER S MANUAL

STEALTH PRO OWNER S MANUAL STEALTH PRO OWNER S MANUAL ALWAYS WEAR A COAST GUARD APPROVED FLOTATION DEVICE WHEN OPERATING THE STEALTH PRO. Know the limits of your abilities and the limits of your equipment. Changes in air temperature

More information

Butler Personnel Parachute Systems, LLC

Butler Personnel Parachute Systems, LLC Butler Personnel Parachute Systems, LLC 1820 Loudon Avenue NW PO Box 6098 Roanoke, VA 24017-0098 (540) 342-2501 (540) 342-4037 (FAX) Info@butlerparachutes.com Butler Personnel Parachute Systems Back Pack

More information

Operating Instructions

Operating Instructions Operating Instructions High Throughput Buffer Exchange or Desalting Dialysis MODEL HTD12a www.htdialysis.com HTD12a : Operating Instructions Components Pressure Plate Clamp In Closed Position Place Stainless

More information

Instruction Manual please read before use

Instruction Manual please read before use Instruction Manual please read before use XL Burner (patent pending) 307 Tchoupitoulas Street, Suite 100 New Orleans, LA 70130 p : 888.596.6960 504.596.6960 e : office@brasafire.com www.brasa.co Item Identification

More information

2008 Equalizer Industries, Inc. Revision 4/23/

2008 Equalizer Industries, Inc. Revision 4/23/ 2008 Equalizer Industries, Inc. Revision 4/23/2018 www.equalizer.com All Equalizer tools are warranted for one year to be free of factory defects. Warranty does not apply to abuse, misuse, or normal wear

More information

Ultimate survival knife The basic survival gear is a knife, so today I am going to be showing you how to make this bush craft knife

Ultimate survival knife The basic survival gear is a knife, so today I am going to be showing you how to make this bush craft knife Ultimate survival knife The basic survival gear is a knife, so today I am going to be showing you how to make this bush craft knife Things you ll need Tools 1. Grinder 2. Emery 3. Clamps 4. Vice grip 5.

More information

How to make an inflatable cube

How to make an inflatable cube How to make an inflatable cube Beta instruction manual produced by Tools for Action. First Edition November 2015. Paris. Second Edition March 2016. Materials & Tools Mylar insulation foil (we use Parotec

More information

Instruction Manual please read before use

Instruction Manual please read before use Instruction Manual please read before use Slim Burner Insert (patent pending) 307 Tchoupitoulas Street, Suite 100 New Orleans, LA 70130 p : 888.596.6960 504.596.6960 e : office@brasafire.com www.brasafire.com

More information

Tuf-Lite III Fans 4000KW Series Hub

Tuf-Lite III Fans 4000KW Series Hub Tuf-Lite III Fans 4000KW Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 11 through 20 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass

More information

VACATION'R A ROOM FOR VERTICAL ARM AWNINGS

VACATION'R A ROOM FOR VERTICAL ARM AWNINGS VACATION'R A ROOM FOR VERTICAL ARM AWNINGS RV Made of durable, lightweight polyester material - the same material used for tents. Does not require hardware that is attached to the RV. No rafters to install.

More information

LESSON ASSIGNMENT. Surgical Asepsis and Sterile Technique. After completing this lesson, you should be able to:

LESSON ASSIGNMENT. Surgical Asepsis and Sterile Technique. After completing this lesson, you should be able to: LESSON ASSIGNMENT LESSON 3 Surgical Asepsis and Sterile Technique. LESSON OBJECTIVES After completing this lesson, you should be able to: 3-1. Identify the basic principles for using sterile materials.

More information

Professional Mandoline Manual. Model: 90757

Professional Mandoline Manual. Model: 90757 Professional Mandoline Manual Model: 90757 Introduction Your MIU France Composite Mandoline features a selection of blades with variable thickness adjustments which make it one of the most versatile kitchen

More information

READ AND SAVE THESE INSTRUCTIONS! EasyAwn Standard Awning Installation

READ AND SAVE THESE INSTRUCTIONS! EasyAwn Standard Awning Installation EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Standard Awning Installation

More information

HOSE ASSEMBLY CLEANLINESS

HOSE ASSEMBLY CLEANLINESS November 18, 2002 HOSE ASSEMBLY CLEANLINESS Preface Hydraulic system cleanliness is a term used to describe the level of solid and liquid contamination found in hydraulic systems. Contamination may be

More information

1946 READ AND SAVE THESE INSTRUCTIONS!

1946 READ AND SAVE THESE INSTRUCTIONS! EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Quarter Round Awning Installation

More information

Operation Manual SUPER BEAST Multi-tool SC-11M-10

Operation Manual SUPER BEAST Multi-tool SC-11M-10 Operation Manual SUPER BEAST Multi-tool SC-11M-10 Technical Specifications General Safety/Operating Instructions Attaching/Changing the Head Using the SUPER BEAST as a Cutter Using the SUPER BEAST as a

More information

Written By: Arthur Shi

Written By: Arthur Shi ipad 5 LTE LCD Replacement Follow this guide to replace the LCD screen in an ipad 5 LTE. Written By: Arthur Shi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Use this guide to replace the

More information

LVS BASE VEST OPERATOR S MANUAL

LVS BASE VEST OPERATOR S MANUAL LVS BASE VEST OPERATOR S MANUAL CONTENTS 02 INTRO 04 FITTING 06 ADJUSTING SIDE-STRAPS 10 STORAGE 14 CARE 16 OPTIONAL SIDE ARMOR 20 COVERS AND ACCESSORIES This manual must be carefully read by all persons

More information

CJ-7 YJ PREPARATION INSTALLING THE WHEEL WELLS. Jeep Wrangler CJ-7/YJ BedRug Interior Installation Instructions

CJ-7 YJ PREPARATION INSTALLING THE WHEEL WELLS. Jeep Wrangler CJ-7/YJ BedRug Interior Installation Instructions CJ-7 YJ BRCJ76R BRCJ81R REAR KITS: BRYJ87R Jeep Wrangler CJ-7/YJ BedRug Interior Installation Instructions Congratulations on choosing the finest interior flooring kit available for your Jeep. BedRug material

More information

Installation and User s Manual 12 x 10 MOTORIZED AWNING

Installation and User s Manual 12 x 10 MOTORIZED AWNING 12 x 10 MOTORIZED AWNING Installation and User s Manual 12 x 10 MOTORIZED AWNING 088-1763-0 Stop Please read and understand this manual before any assembly or use of this product. Before beginning assembly

More information

Chapter 8. Knives and Hand Tools in the Professional Kitchen

Chapter 8. Knives and Hand Tools in the Professional Kitchen Chapter 8 Knives and Hand Tools in the Professional Kitchen Objective Explain the elements of knife construction and how they relate to quality Knives The knife is the chef s most important tool The cutting

More information

READ AND SAVE THESE INSTRUCTIONS! EasyAwn Dome Awning Installation

READ AND SAVE THESE INSTRUCTIONS! EasyAwn Dome Awning Installation EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Dome Awning Installation

More information

For Outdoor Use Only!

For Outdoor Use Only! ITEM NAME: Red Ember 4 ft. Smokestack Rubbed Bronze Fireplace with Cover SKU: ALZ655-1 For Outdoor Use Only! 1. Improper installation, adjustment, alteration, service or maintenance can cause injury or

More information

Tuf-Lite and Tuf-Lite II Fans 6000 Series Hub

Tuf-Lite and Tuf-Lite II Fans 6000 Series Hub Tuf-Lite and Tuf-Lite II Fans 6000 Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 32 and 33 Diameter Hudson Tuf-Lite and Tuf-Lite II fan blades Hudson Tuf-Lite (black) fan blades are made

More information

TJ Tinted Window Kit. Installation Instructions INSTALLATION TIME SKILL LEVEL TOOLS. Vehicle Application

TJ Tinted Window Kit. Installation Instructions INSTALLATION TIME SKILL LEVEL TOOLS. Vehicle Application Installation Instructions TJ Tinted Window Kit Vehicle Application Jeep TJ 2003 and newer Part Number: 58128 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question. Click here

More information

Thank you for purchasing ANYWARE cookware by Little Griddle! ANYWARE

Thank you for purchasing ANYWARE cookware by Little Griddle! ANYWARE A WORD FROM THE MAKER (READ ME FIRST!!!): Thank you for purchasing ANYWARE cookware by Little Griddle! ANYWARE is made from cast aluminum with an advanced ceramic coating and a hightemperature nonstick

More information

Preparation. BEDRUG, INC. n 635 Old Hickory Blvd, Old Hickory, TN n n bedrug.com

Preparation. BEDRUG, INC. n 635 Old Hickory Blvd, Old Hickory, TN n n bedrug.com BRJK07F4, BRJK07F2, FRONT KITS: BTJK07F4, BTJK07F2 Jeep Wrangler JK BedRug/BedTred Interior Installation Instructions Congratulations on choosing the finest interior flooring kit available for your Jeep.

More information

Standard Awning Installation Instructions

Standard Awning Installation Instructions Standard Awning Installation Instructions Important Note: Please become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and will make

More information

Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E

Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E The Trimfast Ream Cutters are reliable, high performance cutters that will give you the results you need quickly

More information

TCWS.38NG03.C BLACK DIAMOND BURNER KIT INSTRUCTIONS

TCWS.38NG03.C BLACK DIAMOND BURNER KIT INSTRUCTIONS IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER These instructions are supplementary to the Installation and Operating Instructions supplied with the fireplace and should be kept together.

More information

1612P MODEL 1612P SLICER MODEL EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO FORM (4-95)

1612P MODEL 1612P SLICER MODEL EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO FORM (4-95) 1612P MODEL 1612P SLICER MODEL 1612P ML-104587 EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO 45374-0001 FORM 19370 (4-95) Installation, Operation, and Care of MODEL 1612P SLICER SAVE THESE INSTRUCTIONS

More information

Making Solar Cells 1 from Household Materials (mostly :)

Making Solar Cells 1 from Household Materials (mostly :) Making Solar Cells 1 from Household Materials (mostly :) Equipment and Materials List Safety Glasses (20+ pairs for students and instructors) Nitrile Gloves (Supreno, 15 pairs of small or medium for students,

More information

FT054 BearMountain OWNER'S MANUAL

FT054 BearMountain OWNER'S MANUAL FT054 BearMountain 10'x10'x84"(H) OWNER'S MANUAL PAT PENDING o 145 145 PENDING PAT o PAT PENDING 145 o 145 PENDING PAT o 145 o PENDING PAT 12 11 10 155 PAT PENDING o Assembly instructions IMPORTANT We

More information

Solar Power Shade INSTRUCTION MANUAL

Solar Power Shade INSTRUCTION MANUAL INSTRUCTION MANUAL 20 June 2006, Revision Initial Release 26 September 2006, version 2 Powerfilm, Inc. 2337 230th Street Ames, IA 50014 (515) 292-7606 Web Site: www.powerfilmsolar.com Table of Contents

More information

Installation & User Manual EW5000 Outdoor Cooking Fire

Installation & User Manual EW5000 Outdoor Cooking Fire Installation & User Manual EW5000 Outdoor Cooking Fire IMPORTANT: Please read this manual before installing and using the ESCEA EW5000 Cooking fire. Failure to follow these instructions may lead to a possible

More information

1 Pan - 6 Ways to Cook!

1 Pan - 6 Ways to Cook! 1 Pan - 6 Ways to Cook! Broil Bake Sauté Fry Steam Braise To see our entire collection of Copper Chef products and all other available accessories, please visit: CopperChef.com *Only Use Non-Metallic Utensils

More information

For Outdoor Use Only!

For Outdoor Use Only! ITEM NAME: Red Ember Bronze Crossweave Firebowl Fire Pit with Free Cover and Fire Tool with Optional Grill Grate SKU: ALZ109 For Outdoor Use Only! 1. Improper installation, adjustment, alteration, service

More information

Latmedical, LLC is the only Caribbean authorize distributor

Latmedical, LLC is the only Caribbean authorize distributor Quality, Value, and Performance are our Promise. Quality in our Products and Operating Systems. Value in our Support Programs and Competitive Pricing. DUKAL's exceeds industry standards on Quality Controls

More information

RUPHIS Blade Clamp. Instruction Manual

RUPHIS Blade Clamp. Instruction Manual RUPHIS Blade Clamp P/N 1006800 NSN 1615-01-562-8156 Instruction Manual AH-64D UH-60A/L UH-60M S-70i S-92 REVISION AUTHORIZATION / RECORD These instructions are primarily for inspection of the RUPHIS Blade

More information

CONVEX Awning Instructions

CONVEX Awning Instructions CONVEX Awning Instructions IMPORTANT NOTE: Please take a few minutes to become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and will

More information

User Manual. 110 Cup (55 Cup Raw) Rice Cooker. Model: 177GRCLP, 177GRCNAT 10/2017. Please read and keep these instructions. Indoor use only.

User Manual. 110 Cup (55 Cup Raw) Rice Cooker. Model: 177GRCLP, 177GRCNAT 10/2017. Please read and keep these instructions. Indoor use only. 110 Cup (55 Cup Raw) Rice Cooker Model: 177GRCLP, 177GRCNAT 10/2017 Please read and keep these instructions. Indoor use only. www.avantcoequipment.com 1 NOTE: Save these instructions for future reference.

More information

IMPORTANT NOTICE. Professional Mandoline Manual

IMPORTANT NOTICE. Professional Mandoline Manual IMPORTANT NOTICE PLEASE DO NOT RETURN TO STORE. If you have any problems with this unit, contact Consumer Relations for service. PHONE: 206-605-0555 Please read operating instructions before using this

More information

Tuf-Lite and Tuf-Lite II Fans 6000M Series Hub

Tuf-Lite and Tuf-Lite II Fans 6000M Series Hub Tuf-Lite and Tuf-Lite II Fans 6000M Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 32.8 or 10 Meter Diameter Hudson Tuf-Lite and Tuf-Lite II fan blades Hudson Tuf-Lite (black) fan blades

More information

Sealing and terminating Wrexham Mineral Cables

Sealing and terminating Wrexham Mineral Cables Sealing and terminating Wrexham Mineral Cables A Termination is required at both ends of each length of cable, and it should be fitted as soon as the cable has been prepared. A complete termination consists

More information

Kontrol Kube Advanced Owners Manual

Kontrol Kube Advanced Owners Manual Mobile Containment. Simplified. TM Kontrol Kube Advanced Owners Manual KONTROL KUBE www.kontrolkube.com 800.343755 1 IMPORTANT SAFETY INFORMATION SAVE THESE INSTRUCTIONS. CAREFULLY READ AND FOLLOW THESE

More information

PLEASE READ BEFORE USE AND SAVE THESE INSTRUCTIONS

PLEASE READ BEFORE USE AND SAVE THESE INSTRUCTIONS Sauce Flip Pan PLEASE READ BEFORE USE AND SAVE THESE INSTRUCTIONS Thank you for purchasing Cook s Companion Sauce Flip Pan. This pan is designed to be one of the most used pans in your kitchen. The Fusion

More information

Operator s Manual. Medium-Duty Electric Slicers ENGLISH. Item Model Description Drive Peak HP Voltage Amps Hz Plug

Operator s Manual. Medium-Duty Electric Slicers ENGLISH. Item Model Description Drive Peak HP Voltage Amps Hz Plug Medium-Duty Electric Slicers 40950 40951 Item Model Description Drive Peak HP Voltage Amps Hz Plug 40950 SLM250/S 10 Knife Medium-Duty Slicer 1/3 2.5 Belt 120 60 5-15P 40951 SLM300P/S 12 Knife Medium-Duty

More information

Corn Flame Energy Corn Stove Model 5000

Corn Flame Energy Corn Stove Model 5000 Corn Flame Energy Corn Stove Model 5000 Installation and Operation Guide Read thoroughly before starting installation Save this manual for future reference SAFETY NOTICE If this stove is not properly installed,

More information

Boardwalk Fire Pit Table

Boardwalk Fire Pit Table Boardwalk Fire Pit Table Installation Instructions 1 P a g e Contents Required Tools....3 Placing the Table 5 Gas Connection..6 Igniter Installation (pt 1)...7 Fire Pit Assembly....8 Igniter Installation

More information

ELECTRIC KNIFE SHARPENER User Guide

ELECTRIC KNIFE SHARPENER User Guide BRAND ELECTRIC KNIFE SHARPENER User Guide Item: 717822 Ginnys.com 800-544-1590 Facebook.com/GinnysBrand Pinterest.com/GinnysBrand Ginnys.com/Blog Thank you for purchasing a Ginny s Brand Electric Knife

More information

Contents. Introduction...3 Description...3. Pack Contents...4. Rada Heavy Duty EV Shower Fittings Right Angled Connector (RAC)...

Contents. Introduction...3 Description...3. Pack Contents...4. Rada Heavy Duty EV Shower Fittings Right Angled Connector (RAC)... SHOWER FITTINGS PRODUCT MANUAL IMPORTANT Installer: This manual is the property of the customer and must be retained with the product for maintenance and operational purposes. Contents Introduction...3

More information

When moving the frame don t force anything! Move the leg to allow the brace to go over the rod.

When moving the frame don t force anything! Move the leg to allow the brace to go over the rod. THE IDLER Assembly and Care Instructions General notes Please read these instructions in their entirety before constructing your Idler Construction Before you begin constructing your Idler consider where

More information

NNIN Nanotechnology Education

NNIN Nanotechnology Education NNIN Nanotechnology Education Student Worksheet Water purity and filtration Getting down to the nanoscale Water Filtration and Nanoparticles Dear Team: February 11, 2009 Thank you for your recommendation

More information

FOREWORD CONTENTS. 1. Preparation and tools required for assembly. 2. Complete parts

FOREWORD CONTENTS. 1. Preparation and tools required for assembly. 2. Complete parts CONNECTOR ASSEMBLY INSTRUCTION MANUAL FOREWORD Thank you for purchasing FOCI s MT-RJ Optical Fiber Connectors. We are confident that our excellent manufacturing procedures and stringent quality control

More information

1. COMPONENT IDENTIFICATION

1. COMPONENT IDENTIFICATION SC Fiber Optic Connectors Field Polish Termination - Singlemode and Multimode Panduit Corp. 2014 INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS COMPLETELY BEFORE PROCEEDING 1. COMPONENT IDENTIFICATION

More information

Professional Mandoline Manual. Model: 90797

Professional Mandoline Manual. Model: 90797 Professional Mandoline Manual Model: 90797 Introduction Your MIU France Stainless Steel Mandoline features a selection of blades with variable thickness adjustments which make it one of the most versatile

More information

SERVICE MANUAL- M126

SERVICE MANUAL- M126 SERVICE MANUAL- MANUAL CAN OPENER- MODEL # 2 1 Model #2 Can Opener Assembly Procedure The Model #2 can opener will be assembled according to the following procedure. I. Model #2 Handle and Arbor Assembly

More information

7. Do not dispose of the packaging immediately.the package insert contains a template for mounting the slide bar A/Rev01 G1/2" G1/2" G1/2"

7. Do not dispose of the packaging immediately.the package insert contains a template for mounting the slide bar A/Rev01 G1/2 G1/2 G1/2 INSTALLATION INSTRUCTIONS Magnetic Slide Shower 550 552 BEFORE YOU BEGIN MAGNETIC SLIDE SHOWER All information is based on the latest product information available at the time of publication. Kohler Co.

More information

READ AND SAVE THESE INSTRUCTIONS! EasyAwn Spear Awning Installation

READ AND SAVE THESE INSTRUCTIONS! EasyAwn Spear Awning Installation EasyAwn Installation, Care and Maintenance Manual EasyAwn Quality, Since 1946 EasyAwn, LLC Toll Free: 877-EasyAwn http://www.easyawn.com READ AND SAVE THESE INSTRUCTIONS! EasyAwn Spear Awning Installation

More information

Table Of Contents RV WEATHERSTRIPPING

Table Of Contents RV WEATHERSTRIPPING Table Of Contents RV WEATHERSTRIPPING SLIDE OUT SEALS....................... 2 DRIP RAIL SEALS....................... 4 VENT HATCH......................... 4 STATIONARY GLASS.................... 5 SLIDING

More information

Chapter 12 Protective Clothing

Chapter 12 Protective Clothing Protective Clothing General Information Protective clothing is worn during inspections of active asbestos removal projects to prevent asbestos exposure, reduce skin irritation, ease decontamination and

More information

--- BIG LEAGUE BATTING CAGE ---

--- BIG LEAGUE BATTING CAGE --- --- BIG LEAGUE BATTING CAGE --- BGLC-7500 Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev-B Page 1 of 22 IMPORTANT NOTICE: 1. BEFORE

More information

MODEL # 1 MANUAL CAN OPENER

MODEL # 1 MANUAL CAN OPENER REV.B SERVICE MANUAL MODEL # 1 MANUAL CAN OPENER Model #1 Can Opener Assembly Procedure The Model #1 can opener will be assembled according to the following procedure. I. Model #1 Handle and Arbor Assembly

More information

CARE, HANDLING & MAINTENANCE FOR ATTACK HOSE, LARGE DIAMETER HOSE (LDH), & SUPPLY HOSE

CARE, HANDLING & MAINTENANCE FOR ATTACK HOSE, LARGE DIAMETER HOSE (LDH), & SUPPLY HOSE CARE, HANDLING & MAINTENANCE FOR ATTACK HOSE, LARGE DIAMETER HOSE (LDH), & SUPPLY HOSE North American Fire Hose Corporation is committed to providing the highest quality raw materials, unique design features,

More information

ULTRA SLIDE OUT AWNING

ULTRA SLIDE OUT AWNING ULTRA SLIDE OUT AWNING SG5000 INSTALLATION GUIDE REV.01262016 RV AWNING PRODUCTS 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500 www.girardrv.com Girard Systems awnings may

More information

LITE Spear Awning Instructions

LITE Spear Awning Instructions LITE Spear Awning Instructions IMPORTANT NOTE: Please take a few minutes to become familiar with this entire document BEFORE beginning your installation. The time you spend doing this is well spent and

More information

Gerjak Dear Customer, You will find below information that includes: Is the caravan rail in order? Is everything in place?

Gerjak Dear Customer, You will find below information that includes: Is the caravan rail in order? Is everything in place? Gerjak Dear Customer, We would like to wish you much pleasure with your new Gerjak product. We very much appreciate that you have chosen our product! Following are some hints and tips to give you pleasure

More information