SPECIFICATIONS. For 1 8 OD Tubing FERRULES FOR 1 8 OD TUBING. One piece PTFE ferrule with SS casing1. One piece PTFE ferrule with SS casing2 008FT32

Transcription

1 4 OMNI-LOK FITTING SYSTEMS OMNI-LOK TYPE P For 1 16, 1 8 or 3 16 OD semi-rigid tubing and ¼ -28 UNF, M6 or UNF threaded flat-bottom ports Pressure rated up to 1000psi (69 bar) when hand-tight High chemical inertness with only PTFE in the fluid path Permanently attached ferrule ideal for repeated connect/ disconnect Ideal for shallow or PTFE ports. The Omni-Lok Type P fitting system uses a pre-assembled one-piece ferrule which when fitted onto tubing offers uniform compression for a secure, permanent fit. Ferrules consist of an inner PTFE sealing surface surrounded by a stainless steel casing with only the PTFE inner portion in the fluid path. The Omni-Lok Type P ferrule design is similar to that of the Omnifit Gripper. Stainless steel casing The fitting nut can spin freely against the ferrule, eliminating tubing twist and subsequent loosening of the nut. A recess in the fitting houses the ferrule, allowing maximum thread engagement between the port and the robust, glass-filled polypropylene fitting nuts. This ensures the system stays sealed when hand-tight up to 1000psi (69 bar) pressure, even in shallow PTFE ports. A range of different color nuts are available for easy line identification. A longer length nut is available for applications where accessibility is an issue (1 8 OD tubing only). PTFE sealing surface PTFE tubing NB: Omni-Lok type P fittings require no special tooling for assembly, but fixing of the ferrule onto tubing does require the aid of pliers or similar. See the assembly instructions on our website for full details. For 1 8 OD Tubing FERRULES FOR 1 16 OD TUBING FERRULES FOR 1 8 OD TUBING 008FT16 One piece PTFE ferrule with SS casing1 008FT32 One piece PTFE ferrule with SS casing2 NUTS FOR 1 16 OD TUBING NUTS FOR 1 8 OD TUBING 008NF16-YC5B PP Black ¼28 008NF16-YC5U PP Blue ¼28 008NF16-YC5W PP Brown ¼28 008NF16-YC5A PP Gray ¼28 008NF16-YC5G PP Green ¼28 008NF16-YC5N PP Orange ¼28 008NF16-YC5R PP Red ¼28 008NF16-YC5H PP White ¼28 008NF16-YC5Y PP Yellow ¼28 008NF16-YC5V PP Violet ¼28 008NF16-YC6B PP Black M6 1The 008FT16 ferrule can be used with all nuts listed and is suitable for both ¼28 and M6 flat-bottom ports. 008NF32-YC5B PP Black ¼28 008NF32-YC5U PP Blue ¼28 008NF32-YC5W PP Brown ¼28 008NF32-YC5A PP Gray ¼28 008NF32-YC5G PP Green ¼28 008NF32-YC5N PP Orange ¼28 008NF32-YC5R PP Red ¼28 008NF32-YC5H PP White ¼28 008NF32-YC5Y PP Yellow ¼28 008NF32-YC5V PP Violet ¼28 008NF32-YL5B PP Black ¼28 008NF32-YC6B PP Black M6 2 The 008FT32 ferrule can be used with all nuts listed and is suitable for both ¼28 and M6 flat-bottom ports.

2 For 3 16 OD Tubing A nut and ferrule combination specifically to connect 3 16 OD tubing into UNF flat-bottom ports. OMNI-LOK FITTING SYSTEMS 5 FERRULES FOR 3 16 OD TUBING 008FT47 One piece PTFE ferrule with SS casing NUTS FOR 3 16 OD TUBING 008NF47-YC7B PP Black FT-16 Type P ferrule for 1 16 OD tubing 008FT-32 Type P ferrule for 1 8 OD tubing 008FT-47 Type P ferrule for 3 16 OD tubing NF16-YC5U ¼28, blue 008NF16-YC6B NF32-YC5R ¼28,red 008NF32-YC6B 2 [1.142] Ø786 [0.310] [0.933] 008NF32-YL5B Long nut for 1 8 OD tubing, ¼28, black [0.500] 008NF47-YC7B Nut for 3 16 OD tubing , black TECH TIP: Problems with shallow or PTFE ports? Some shallow ports, especially those found in solenoid valves, may offer limited thread engagement for most standard fittings. Ports machined from PTFE can also be slippery and difficult to seal, with fittings becoming loose and backing out. With glassfilled polypropylene and a recessed ferrule, Omni-Lok fittings are specifically designed for for use in shallow and PTFE ports to ensure maximum security and a leak-free seal.

3 6 OMNI-LOK FITTING SYSTEMS OMNI-LOK TYPE S For 1 16, 1 8 or 3 16 OD rigid or semi-rigid tubing and flat-bottom ¼ -28 UNF, M6 or UNF threaded ports Pressure rated up to 500psi (34 bar) when hand-tight Chemically resistant only PEEK or ETFE in the fluid path ETFE ferrules can be used with rigid tubing such as stainless steel or PEEK The Omni-Lok Type S fitting system uses an easy to assemble twopiece ferrule which when fitted onto tubing offers uniform compression for a secure, permanent fit. Two-part ferrules consist of an inner PEEK or ETFE sealing surface surrounded by a stainless steel lock ring with only the inner portion in the fluid path. Stainless lock ring The fitting nut can spin freely against the ferrule, eliminating tubing twist and subsequent loosening of the nut. A recess in the fitting houses the ferrule, allowing maximum thread engagement between the port and the robust, glass-filled polypropylene fitting nuts ensuring the system stays sealed when hand-tight up to 500psi (34 bar) pressure even in shallow PTFE ports. A range of different color nuts are available for easy line identification and a longer length nut is available for 1 8 OD tubing for applications where accessibility is an issue. PEEK or ETFE sealing surface Perfect for rigid tubing such as stainless steel or PEEK! The Type S ETFE ferrule is ideal for fitting to rigid tubing such as PEEK or stainless steel. NB: Omni-Lok Type S uses a two-part ferrule and requires assembly using the special Assembly Tool - see page 7. For 1 8 OD Tubing FERRULES FOR 1 16 OD TUBING 008FK16 008FZ16 PEEK ferrule with separate SS lock ring1 ETFE ferrule with separate SS lock ring1 FERRULES FOR 1 8 OD TUBING 008FK32 008FZ32 PEEK ferrule with separate SS lock ring2 ETFE ferrule with separate SS lock ring2 NUTS FOR 1 16 OD TUBING 008NF16-YC5B PP Black ¼28 008NF16-YC5U PP Blue ¼28 008NF16-YC5W PP Brown ¼28 008NF16-YC5A PP Gray ¼28 008NF16-YC5G PP Green ¼28 008NF16-YC5N PP Orange ¼28 008NF16-YC5R PP Red ¼28 008NF16-YC5H PP White ¼28 008NF16-YC5Y PP Yellow ¼28 008NF16-YC5V PP Violet ¼28 008NF16-YC6B PP Black M FK16 and 008FZ16 ferrules can be used with all nuts listed and are suitable for ¼28 and M6 flat-bottom ports. NUTS FOR 1 8 OD TUBING 008NF32-YC5B PP Black ¼28 008NF32-YC5U PP Blue ¼28 008NF32-YC5W PP Brown ¼28 008NF32-YC5A PP Gray ¼28 008NF32-YC5G PP Green ¼28 008NF32-YC5N PP Orange ¼28 008NF32-YC5R PP Red ¼28 008NF32-YC5H PP White ¼28 008NF32-YC5Y PP Yellow ¼28 008NF32-YC5V PP Violet ¼28 008NF32-YL5B PP Black ¼28 008NF32-YC6B PP Black M FK32 and 008FZ32 ferrules can be used with all nuts listed and are suitable for ¼28 and M6 flat-bottom ports.

4 OMNI-LOK FITTING SYSTEMS 7 For 3 16 OD Tubing A nut and ferrule combination specifically to connect 3 16 OD tubing into UNF flat-bottom ports. OMNI-LOK TYPE S ASSEMBLY TOOL For easy assembly of Omni-Lok two-part ferrules onto tubing in seconds! FERRULES FOR 3 16 OD TUBING 008FK47 008FZ47 NUTS FOR 3 16 OD TUBING PEEK ferrule with separate SS lock ring ETFE ferrule with separate SS lock ring The Omni-Lok Type S two-piece ferrule is easily assembled onto tubing using this tool. Simply cut the tube end square, then fit the Omni-Lok ferrule and lock ring onto the squarely cut tube end, load into the assembly tool and squeeze the tool handles together to press the lock ring onto the ferrule. Full instructions are provided with the tool and on our website. 008NF47-YC7B PP Black 5/ [0.110] 2.80 [0.110] 008NF16-YC5U ¼28, blue 008FK16 Two-part ferrule, PEEK 008FZ16 Two-part ferrule, ETFE 1 008NF32-YC5R ¼28,red 008FK32 Two-part ferrule, PEEK 008FZ32 Two-part ferrule, ETFE [1.142] 008NF16-YC6B 008NF32-YC6B 008NF32-YL5B Long nut for 1 8 OD tubing, ¼28, black OMNI-LOK TYPE S ASSEMBLY TOOL 008AT Assembly tool ea TUBING CUTTER Tubing cutter ea Ø786 [0.310] [0.933] 2.65 [0.104] 2.65 [0.104] Replacement blades ea Ø6.35 [0.250] [0.500] 3.45 [0.1364] Ø6.35 [0.250] 3.45 [0.1364] 008NF47-YC7B Nut for 3 16 OD tubing , black 008FK47 Two-part ferrule, PEEK 008FZ47 Two-part ferrule, ETFE

5 8 OMNI-LOK FITTING SYSTEMS OMNI-LOK INVERTED CONE FITTINGS Removable and reusable system for quick and convenient low-pressure connections For 1 16, 1 8 or 3 16 OD and metric sizes 2.0, 2.5 or 3.0mm OD tubing For flat-bottom ¼ -28 UNF, M6 or UNF threaded ports Pressure rated up to 250psi (17 bar) when hand-tight Omni-Lok inverted cone fittings provide a simple, easy to use lowpressure connection. No tools are required to assemble a flangeless fitting quickly and economically - just slip the fitting nut and the ETFE cone over the tubing and screw into the port. Only the ETFE inner portion is in the fluid path and with none of the parts permanently attached to the tubing, fittings can easily be removed and reused. A recess in the fitting houses the inverted cone, allowing maximum thread engagement between the port and the robust, glass-filled polypropylene fitting nuts ensuring the system stays sealed when handtight even in shallow PTFE ports and up to 250psi (17 bar) pressure. ETFE inverted cone NB: Omni-Lok Inverted Cones do not require any special tools for assembly [0.189] INVERTED CONES FOR 1 16 OD TUBING 008CZ16 ETFE inverted cone 008NF16-YC5U ¼28, blue 008NF16-YC6B 008CZ-16 Omni-Lok inverted cone for 1 16 OD tubing NUTS FOR 1 16 OD TUBING NC16-YC5U PP Blue ¼28 008NC16-YC5G PP Green ¼28 008NC16-YC6U PP Blue M [0.122] Ø5.00 [0.197] For 1 8, 2.0, 2.5 and 3.0mm OD Tubing 008NF32-YC5R ¼28, red 008NF32-YC6U M6, blue 008CZ-32 Omni-Lok inverted cone for 1 8 OD tubing INVERTED CONES FOR 1 8, 2.0, 2.5 & 3.0MM OD TUBING For 3 16 OD Tubing MATERIAL TO FIT TUBE OD QTY 008CZ19 ETFE mm 008CZ25 ETFE 2.5mm 008CZ30 ETFE 3.0mm 008CZ32 ETFE 1 8 (3.2mm) NUTS FOR 1 8, 2.0, 2.5 & 3.0MM OD TUBING1 008NC32-YC5U PP Blue ¼28 008NC32-YC5G PP Green ¼28 008NC32-YC5N PP Orange ¼28 008NC32-YC5R PP Red ¼28 008NC32-YC5Y PP Yellow ¼28 008NC32-YC6U PP Blue M6 A standard blue nut and ferrule combination specifically to connect 3 16 OD tubing into UNF flat-bottom ports is available. INVERTED CONE FOR 3 16 OD TUBING 008CZ47 ETFE inverted cone NUTS FOR 3 16 OD TUBING 008NC47-YC7U PP Blue Ø786 [0.310] [0.933] 3.20 [0.126] 1 The 008NC nuts can be used with all tube sizes and ferrules listed 008NF47-YC7U Nut for 3 16 OD tubing , blue [0.500] Ø6.60 [0.260] 008CZ-47 Omni-Lok inverted cone for 3 16 OD tubing

6 OMNI-LOK FITTING SYSTEMS 9 HIGH TEMPERATURE INVERTED CONE FITTINGS Removable and reusable system for low-pressure connections in harsh environments or higher temperatures For 1 16 or 1 8 OD tubing and flat-bottom ¼ -28 UNF threaded ports Pressure rated up to 250psi (17 bar) when hand-tight These inverted cone fittings in robust PEEK are designed to provide a simple, easy to use low-pressure connection for use in environments where harsh chemicals or higher temperature preclude the use of a polypropylene fitting. Compact head fittings are available for where space is limited. Inverted cones and fittings are easily reusable because components are not permanently fixed to the tubing. Simply slip the nut and inverted cone over the end of the tubing and screw into the port. Connections are pressure rated up to 250psi (17 bar) pressure. ETFE inverted cone NB: Inverted cone fittings do not require any special tools for assembly INVERTED CONES FOR 1 16 OD TUBING Ø10.00 [0.394] Ø6.30 [0.249] ETFE inverted cone 4.80 [0.189] PEEK NUTS FOR 1 16 OD TUBING HEAD STYLE Standard PEEK Natural ¼28 ea Compact PEEK Natural ¼28 ea PEEK nut for 1 16 OD tubing, ¼ Compact PEEK nut for 1 16 OD tubing, ¼ Inverted cone for 1 16 OD tubing For 1 8 OD Tubing INVERTED CONES FOR 1 8 OD TUBING Ø10.00 [0.394] Ø6.30 [0.249] ETFE inverted cone 4.60 [0.181] PEEK NUTS FOR 1 8 OD TUBING Ø4.90 [0.193] HEAD STYLE Standard PEEK Natural ¼28 ea Compact PEEK Natural ¼28 ea PEEK nut for 1 8 OD tubing, ¼ Compact PEEK nut for 1 8 OD tubing, ¼ Inverted cone for 1 8 OD tubing TECH TIP: Frequent connection / disconnection? For applications needing repeated connect / disconnect we recommend a permanently attached ferrule. Choose from our Omni-Lok and Gripper ranges.