17500 VRANJE, SRBIJA Radnička 1, Tel.: 017/ INSTRUCTIONS FOR INSTALLATION, ADJUSTMENT AND USE

Transcription

1 17500 VRANJE, SRBIJA Radnička 1, Tel.: 017/ STOVE OF THICK METAL SHEETS PREMIJER PREMIJER K INSTRUCTIONS FOR INSTALLATION, ADJUSTMENT AND USE 1.Technical data about continuously burning stove of thick metal sheets 1

2 -width (Premijer / Premijer K ).580 / 603mm -depth (Premijer / Premijer K ) mm -height (Premijer / Premijer K ) / 1135mm -diameter of flue extension mm -stove mass (Premijer / Premijer K).. 190kg / 215kg -Rated heating power.. 7 KW -heating volume: non-insulated housing.75m 3 insulated housing..100m 3 -flue draft....12pa 2. Description of continuously burning stove of thick metal sheets According to its construction, the continuously burning stove of thick metal sheets differs from the other solid fuel stoves, both in the design, as well as in the composition of certain elements. It is made of sheet metal positions with a cast grate which provides it very easy maintenance and cleaning. The doors of the stove are made of cast iron positions fitted with sealing pigtails which provide tightness and enable function in operation. The firebox cladding is made of steel sheet with a thickness of 4 and 3 mm. The firebox is inlaid with changeable chamotte plates. The emission heat is emitted by hot external surfaces of the stove, and especially through the glass. The primary and secondary air intake opening is located on the back side of the stove. 3.Air regulation (fig.1) Primary and secondary air regulation is performed by knobs located below the extension of the lower door, which is previously open (fig. 1). The air flow is shown on fig.2. Secondary air regulation knob Primary air regulation knob 3.1. Primary air regulation fig.1 2

3 The lower knob is for primary air regulation. The shaft is connected to a thermostat which depending on the set power from 0 to 5 automatically releases certain quantity of air, which through the firebox grate enters in the firebox from below and enables fuel combustion according to previously desired and set temperature. Make sure that the ashtray is not overfull and that it is regularly emptied, in order to provide free air intake Secondary air regulation The upper knob is for secondary air regulation. The shaft is connected to a secondary air intake flap. The secondary air supplies the required oxygen for the firebox, thus enabling full fuel combustion. The secondary air intake regulators must not be completely closed since the glass would become smoky and high emissions of harmful substances would be created which can lead to flue clogging. Topli Hot vazduh air Odvod Flue gas dimnih outlet gasova Flue Dimni gases gasovi are exhausted se odvode through preko usmerivača a gas router gasova Dovod Secondary sekundarnog air intake vazduha for combustion-2 za sagorevanje-2 Dovod Secondary sekundarnog air intake vazduha for combustion-1 za sagorevanje-1 Dovod primarnog vazduha Primary air intake for za sagorevanje combustion Hladan Cold air vazduh Fireplace Kamin PREMIJER PREMIJER strujanje air flow vazduha fig.2 4. Handling and manner of use 4.1. Stoking Before ignition, open the air intake regulators. Ignition is performed with paper and chopped wood. 3

4 Ignite the paper and leave the door half-open, so that the sealing pigtail will not stick to the stove paint. The paint completely hardens even after few hours of heating. During the first hours of operation, due to pain hardening, an unpleasant smell might be created in the rooms where stoking is performed. Please, aerate the room well. When the chopped wood filling is well inflame, open the door and fill the stove firebox with the required quantity of adequate fuel. In order to maintain the glass without smoke as long as possible, wood should always be piled so that the cut surface is not turned towards the glass. During paint hardening, please do not he paint or do not put anything on the stove, in order to avoid paint damaging. The stove firebox is inlaid with chamotte plates. The chamotte plates activate heat, and emit it also in the firebox thus increasing the combustion temperature. During stoking of the stove in the transit period, fill the firebox with a smaller quantity of wood. Open the air regulators more so that the current fuel can burn away faster (with the creating of flame), thus stabilizing the flue draft. In order to avoid poor combustion in the firebox, the ash should be more frequently and carefully shined with intense heat Safety measures while using the stove Never use water to extinguish fire. The stove must not be placed on an inflammable pad, that is, the floor must be made of inflammable material, for example plate of metal sheet, ceramics etc. The pad must cover at least 60cm in front of the stove and 20 cm from the sides. The distance to the back wall must be at least 20cm. Inflammable elements must not be found in the area of emission of the stove. The unpleasant smell cannot be avoided. It will disappear, but after few hours, when the paint hardens. During stove commissioning, the paint is soft. Please do not wipe the stove with a cloth and do not put anything on it. Empty the content of the ashtray in some metal or inflammable container intended solely for that purpose. The seemingly cooled ash can be very hot even after cooling for some time. 5. Installation of the continuously burning stove For proper installation of the stove, you should check the draft in the flue, since a good draft is a condition for proper stove operation. Check of the draft strength is best and most easily performed by using a candle (see figure 3). slight draft good draft very strong draft fig.3 4

5 The draft strength depends on the following variables: - on the flue regularity, - on the atmospheric conditions (season), - on the regularity of the stove and other heating elements connected to the flue, - on the position of the house in the environment (whether it is on a hill, plain or valley). If draft in the flue is insufficient, then this can lead to poor combustion and creation of smoke on the glass. 6. Maintenance of the continuously burning stove Mechanical cleaning of the flue pipe is compulsory and must be performed few times in a year, including at least once during the heating season. Check connections and the locking devices, especially parts that provide sealing. Clean the stove grate on regular basis, so that it would remain functional. During stoking of the stove, make sure that smoke is not created on the glass. Smoke is created due to poor combustion, for several reasons: - poor flue draft (bad flue), - the stove is inappropriately used, for example the supply of oxygen is damped too early. We have no influence on these factors. For this reason we do not provide guarantee for the clean glass. In order to keep the glass as clean as possible, the wood should always be inserted so that the truncation surfaces are not in the direction of the glass. The higher the temperature of combustion, that fewer incombustible substances are contained in the exhaust gases. The chamotte plate is easily changeable. The chamotte plate cannot be damaged from mechanical impact. If crack is visible on the chamotte plate, it still does not have to be replaced. This must be done if metal parts behind it are visible. The outer part of the stove should be cleaned with a dust brush or a dry cloth, not with a cloth or water. 7. TIME OF GUARANTEED SERVICING This implies the period during which we guarantee the service, accessories and space parts, starting from the day of purchase of the device. The time of guaranteed servicing is in accordance with the valid legal regulations. In case of change of the model and the design of the device, the term for change of parts that have modified design is within the legal term. After this term we provide the modified parts in the new designs. 7.1 CONDITIONS OF THE GUARANTEE The guarantee of the product is valid within the legally defined term. The guarantee is not valid for the glass, the glass-ceramic panel and the physical damages that have occurred after purchase. THE MANUFACTURER RETAINS ALL THE RIGHTS TO MAKE CHANGES. The device will properly function within the guaranteed term only if it is used in accordance with these guidelines for connection and application. The guarantee cases to apply if it is determined that: -the connection or the repair of the product was performed by an unauthorized person, that is, if unoriginal parts have been embedded, - if the device has not been properly used in accordance with these guidelines, 5

6 - if some mechanical damaging of the device occurred during usage, - if the repairs of defects were performed by an unauthorized person, - if the device has been used for commercial purposes, - if the damage has occurred during transportation after the device was sold, - if the defects occurred due to improper mounting, improper maintenance or mechanical damaging by the buyer, - if the defect occurred after too strong or insufficient power, as well due to force major. We can repair the defects of Your device also outside the guaranteed period, with original spare parts for which we also provide a guarantee under the same conditions. This guarantee does not exclude or affect the rights of the customer in regard to the conformity of the goods pursuant to the legal regulations. If the delivered product does not conform to the agreement, the customer has the right to ask the seller to repair that lack of conformity without any reimbursement, by repair or change of the product in accordance with the valid legal regulations. 6