Shark Guard Installation
|
|
- Teresa Sheena Fox
- 5 years ago
- Views:
Transcription
1 Shark Guard Installation
2 In the Package When you receive your Shark Guard, verify that nothing was damaged in shipping. Here is a current list of parts that should be included with a standard Felder and Hammer saw packages. You won't find a printed manual inside the box. This is cost reduction to you. It's Greener and also allows you to get the most up to date information by viewing this online. Please print out the PDF instructions from the link above. The guard Clamp and knob assembly Two riving knives Shark face decals Other accessories you may have ordered
3 Riving Knife Lets start with the riving knife. This is the heart of this guard system and will be used most often. I suggest you apply some Johnson's Paste wax or Minwax Paste wax to the riving knife. This should be done periodically to clean and protect the riving knife and to slick up the surfaces to reduce friction. DISCONNECT THE POWER SOURCE. NEVER COUNT ON YOUR SWITCH ALONE TO CONTROL THE POWER WHEN WORKING ON MACHINERY. THEY CAN FAIL. Currently, this riving knife is designed to mount very much like your OEM blade guard. It utilizes the mounting hardware and mounting point inside the throat plate and behind the saw blade away from the operator. Remove your throat plate. It may also be easier initially to remove the saw blade as well. This would be a good time to clean out the inside of your saw. Remove any knife or guard that you have mounted now. There are two riving knives that come with the SG package. These are for 10 and 12 inch blades. The top of the SG riving knife has to remain parallel to the table top in order to work properly. It shouldn't take any longer to swap out the riving knives than it would to adjust the orignal knife when changing blades, so this difference should not cost any time.
4 Insert the riving knife you intend to use following the instructions in your saws Operator's manual. The big knife is for 12 inch blades. The knives are engraved to help tell them apart at a glance. The RK should sit so that the top is level or parallel with the table top and just shy of as high as the blade teeth. There is only a 1/16" difference or less between the top of the RK and the blade height. A scrap piece of material can help check this difference, but you could use different types of measuring devices. See images above. Check to make sure that you have clearance at the top, back and at the blade teeth along the front arc of the RK. Spin the blade carefully by hand to check for any contact. Sight down the front of the blade or use a straight edge ruler to determine that the splitter is trailing behind the blade. It should not be outside the blade path or blades teeth when checked with a straight edge front to back. These guards are designed to be used just a bit different than the original. Aside from the other features of easy removal and versatility, they feature a hold down. You must set the guard height every time you change material thickness. This insure that the stock will feed under the guard as well as have that extra safety of the clamp acting as a hold down device. This prevents the stock from lifting off the table. Lifting stock is how most kickbacks start, so setting this each time provides both smooth operation of the guard as well as the extra protection not afforded by the factory guard. It is imperative that the guard be at the correct height for the material that you are cutting. You must set the guard for the material thickness each time you change to a different thickness. Feeding the wrong thickness material can be dangerous. It can stop material in mid
5 cut. Always check or adjust the guard height for material being cut. This is designed this way so that when you remove the guard and clamp, you have a true riving knife that can be left in place for non-through cuts. This insures that when a riving knife is needed on the saw, it is there. No fiddle factor. Having to align the riving knife each and every time you swap them out on these saws can become a real issue with time constraints as well as ease of use. This lessens the risk of not having a knife on the saw when needed. There are now warning labels on all SGK1 shark guards that serve to help as a reminder to do this for you and others who may use the saw. If you have an older Shark Guard, send me an and I will get a warning label with instructions mailed to you. The image below is an older style RK and clamp for Powermatic 2000, but are similar to the new ones that ship with the SGK1.
6 Riving Knife Alignment At this point of setup you will need to align or verify alignment of the RK to the blade. Install your blade if you have removed it earlier. You will need to use a straight edge, steel ruler, framing square or something similar. The RK needs to be completely in the shadow of the blade. Alignment can be accomplished a few different ways. Refer to your Operator's Manual.
7 The Clamp assembly Once you have the riving knife securely installed and aligned, you can install your throat plate. Install this according to your Operator's manual. The three slots on the top of the two largest splitters are used with this clamp. The three steel pins in the lower portion of the clamp slip into these slots and lock down when the knobs of the clamp are tightened. There are also set screws in one clamp half that serve to keep the two clamp halves parallel when tightening regardless of RK thickness. You loosen the knobs and slide the clamp toward the rear of the saw and lift up. Installation is the reverse. This clamp helps to prevent lifting of the material depending on material thickness being cut. Feeding the wrong thickness material can be dangerous. It can stop material in mid cut. Always check or adjust the guard height for material being cut.
8 Using the tail hook The Shark Guard has a horizontal hooked slot at the rear and a vertical slot further forward. These slots are the mounting slots for this guard. The hooked slots get hooked on the rear studs of the clamp. There is a safety hook that slips down over the rear stud to keep the guard from coming off when not intended. You can see in this image that the guard can be left in the upward position by hooking only the rear slots and resting the guard on the front stud and brass bushings. This ability is beneficial when measuring between the fence and blade with a steel rule. The front slots just slip down over the front studs with care taken to use the smaller bushing diameters. With this done and your tail hook swung down into place, your blade guard is installed.
9 Using the Shark Guard Here is a link to some video's that help to show how these guard are intended to be used. Watch the videos that deal with riving knives. This guarding system is designed to collect maximum dust during a cut, so the front roller underneath always rides on the stock. This helps prevent dust from getting slung forward by the blade on most cuts except at the very end of the cut and when cleaning up an edge. All guards with dust collection have trouble in those areas. If you ordered a guard with a dust port, a dust collection hose can be hooked up to the top of the guard using a hose clamp or just by slip fit. The dust port to hose connection is usually a snug fit. I suggest that something be done to the port though. If left open, you can get a fountain effect of sawdust right into your face. For a good fit with something that is readily available, spray paint tops will serve as a good cap for the 2.5 inch dust port. Larger ports might be capped using various plastic lids or tops.
10 Dust collection installations Rockler, Woodcraft and other outlets sell nice clear flex hose that fit these dust ports very well. If you leave the hose as a slip fit without a clamp, the hose can conveniently do duty on a router table as well. If you are installing a larger hose, you should also include a blast gate in line and easily accessible. This really is a requirement for 4 inch ports and is a good idea for smaller ones. When you will be cutting material that will have a small offcut, the suction from the dust port can be so powerful that it will lift the small parts and it can get thrown into the dust hose or into the front of the guard with extreme force. This is undesirable and easily prevented with a blast gate. There are numerous ways the you can support the hose for the dust collection. On my Gallery page, you will see some photo's of different setups. On my Review page, you will find links to individual websites where some owners used varied methods of supporting this hose. Here is a link with information on mounting the SGK1 overhead.
11 Shark face decal application The decals come in two parts. The mouth and the eye. If you are looking at the shark from the front, the decals go in on the left side. We recommend that you use Windex (any glass cleaner) and a soft cotton cloth like a T-shirt to clean the guard first. It may help to look at a photo like this one below. Remember, you are looking at the reverse side in this image. This was done so that you wouldn't have to handle the decal when moving the shark. It also gives is a nice appearance from the outside of the lexan. These are water slide decals. Below are the instructions for applying these. Place decal into a cup of clean water for seconds and remove when the thin decal film begins to slip along backing. (Discard backing material after the decal has been removed) Apply decal to clean surface. Here is a link to a PDF file that you can print out. It will help you get the proper placement for these. Just print page two. Lay the guard down on the image and then you will be able to place the decals on the inside where they should go. Once you have them in position, gently pat the decals dry with a soft cloth or towel going from one side to the other. Insure there are no air bubbles under the decals. They should dry in a matter of hours. Decal placement file.
12 Care and cleaning of the Shark Guard For splitters and riving knives, I suggest paste wax like Johnson's or Minwax to both clean and smooth the surfaces for less friction. On the guards we like to use Windex and a soft cloth to periodically keep the guard clear. Dust can build up inside and out, so it provides the best visibility when clean. Replacement parts Replacement, spare or upgrade parts can be ordered using this link. If you don't find what you need there, then just send an . Still have questions or concerns? If you have any questions about installation, setup or usage of this blade guard or parts associated with it, please don't hesitate to contact us. We are happy to help insure your satisfaction and safe usage of these products. Thanks a bunch and I hope that you enjoy using your Shark Guard.
Shark Guard SGK1 Installation
Shark Guard SGK1 Installation for riving knife based saws These instructions apply to numerous brand and model saws that we make guards for. This information is fairly generic and good for all those saws.
More information1000M MANUAL Signature Series Slicer OPERATORS MANUAL
1000M MANUAL Signature Series Slicer OPERATORS MANUAL Persons under age 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. Of Labor Employment Standards Administration
More informationAFC-50 Automatic French Fry Cutter Instruction Manual
AFC-50 Automatic French Fry Cutter Instruction Manual Fry Factory Inc. 67 Watts Ave, Charlottetown, PEI, C1E 2B7, Canada Phone: 902-368-2900 Fax: 902-368-8645 Email: info@fryfactoryinc.com Website: www.fryfactoryinc.com
More informationThomas Scientific Swedesboro, NJ U.S.A.
Thomas Scientific Swedesboro, NJ 08085-0099 U.S.A. Wiley Laboratory Mill, Model 4 3375-E10 (115 V, 50/60 HZ) USE AND CARE OF CATALOG NUMBER: 3375-E10 Wiley Laboratory Mill, Model 4 (115 V, 50/60 HZ) UNPACKING
More informationSERVICE MANUAL- M126
SERVICE MANUAL- MANUAL CAN OPENER- MODEL # 2 1 Model #2 Can Opener Assembly Procedure The Model #2 can opener will be assembled according to the following procedure. I. Model #2 Handle and Arbor Assembly
More informationFLEX KEY ASSEMBLY. ..._ o RAFTER ARM TUBE MAIN ARM TUBE CAP NUT CLAW HINGE
ZIP DEE Inc. 96 Crossen Ave. Elk Grove Village, IL 60007(847)437-0980 (800)338-2378 HEAD CASTING AWNING RAIL FLEX KEY ASSEMBLY..._ o GM1 Installation Instruction GMC Motorhome RAFTER ARM TUBE MAIN ARM
More informationMODEL # 1 MANUAL CAN OPENER
REV.B SERVICE MANUAL MODEL # 1 MANUAL CAN OPENER Model #1 Can Opener Assembly Procedure The Model #1 can opener will be assembled according to the following procedure. I. Model #1 Handle and Arbor Assembly
More informationMAX Series 9514 OPERATOR S MANUAL
MAX Series 9514 OPERATOR S MANUAL Persons under age 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. Of Labor Employment Standards Administration Fact Sheet
More informationProduct instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E
Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E The Trimfast Ream Cutters are reliable, high performance cutters that will give you the results you need quickly
More informationDO NOT USE WITH CROSSBAR SPREAD LESS THAN 24.
TM Please read all instructions carefully before assembly, installation and/or use of this product. DO NOT USE WITH CROSSBAR SPREAD LESS THAN 24. WARNING: Do not exceed the weight limit of your vehicle
More informationFORM (Apr. 2006)
2212 Slcier MODEL 2212 SLICER MODEL 2212 ML-136132 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 35215 (Apr. 2006) Installation, Operation, and Care of MODEL 2212 Slicer
More informationM129 SERVICE MANUAL- M129 MODEL #G-2 MANUAL CAN OPENER
SERVICE MANUAL- M129 MODEL #G-2 MANUAL CAN OPENER Model #G-2 Can Opener Assembly Procedure The Model #G-2 can opener will be assembled according to the following procedure. I. Model #G-2 Handle and Arbor
More informationRAFTER VI. Installation and Operation CAREFREE WITH AUTOMATIC AWNING SUPPORT. RV Accessory PRODUCT OVERVIEW
CAREFREE RAFTER VI RV Accessory WITH AUTOMATIC AWNING SUPPORT Installation and Operation PRODUCT OVERVIEW The gives the awning user the ability to easily tighten the center fabric when the awning is extended.
More informationINSTALLATION INSTRUCTIONS AND OWNER'S MANUAL AWNINGS. For trailers & motor homes with straight sides TOOLS REQUIRED
AWNINGS INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL For trailers & motor homes with straight sides TOOLS REQUIRED 1/4" electric drill Ratchet handle kit 3/8" & 7/16" socket No. 1 and No. 2 screwdriver
More informationPR-429BF-600M. Bell 429 Blade Fold Kit Operations Manual
Table of Contents Table of Contents... 1 Record of Revisions... 2 References... 3 Introduction... 4 Contact Information... 4 Prerequisites... 5 First Time Use... 6 Blade Clamp Placement... 6 Blade Clamp
More informationTidland Class II Razor Cartridge
TIDLAND SLITTING SOLUTIONS Tidland Class II Razor Cartridge Installation and Operation EN MI 755910 1 This document is for use with Tidland Performance Series Knifeholder Manuals Automatic, Manual or Crush
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationRETRACTABLE AWNING w/ OPTIONAL HOOD ASSEMBLY INSTRUCTIONS
Contact us @ (800)851-0865 RETRACTABLE AWNING w/ OPTIONAL HOOD ASSEMBLY INSTRUCTIONS Congratulations on your purchase of a new retractable awning. With proper installation this awning will provide years
More informationColor Light Streams Lighted Bubbler Spillway Pot (CLSDLP) Installation Manual
Color Light Streams Lighted Bubbler Spillway Pot (CLSDLP) Installation Manual 27.75 23.75 25.50 20.75 Specifications: 8-13 GPM 12-14 VAC only (Class 2 transformer required) 3W max. 100 ft. cord, conduit
More informationfunctionality with the necessary maintenance tools stored in a convenient built in tool box, as well as parallel handles for
GuilloMax User Manual The Guillomax has distinct features such as its unique structure and ease of cutting. It combines symmetry with functionality with the necessary maintenance tools stored in a convenient
More information1612P MODEL 1612P SLICER MODEL EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO FORM (4-95)
1612P MODEL 1612P SLICER MODEL 1612P ML-104587 EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO 45374-0001 FORM 19370 (4-95) Installation, Operation, and Care of MODEL 1612P SLICER SAVE THESE INSTRUCTIONS
More information4A1-114/114KR & 4A1-2 MANUAL TENSIONERS
M L. C O O N AL TO 4A1-114/114KR & 4A1-2 W W W.T R AD IT IO MANUAL TENSIONERS READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SEVERE PERSONAL INJURY. GENERAL SAFETY
More informationNotes, Parts List & Drawings
Biomass Chopper/Cutter Notes, Parts List & Drawings Page 1 of 16 The Easy BioChop biomass chopper/cutter was designed to cut both wet and dry biomass and to accomplish a number of goals. The objectives
More informationInstallation Guide. LPKPDR - Universal LP Conversion Kit for Professional & Designer Ranges/Rangetops. Viking Range, LLC.
Installation Guide Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-845-4641 LPKPDR - Universal LP Conversion Kit for Professional
More informationAssembly TOOLS REQUIRED: 17mm and 14mm or equivalent wrenches.
Instructions for 3 Trimmer Rack, 3TR* *Patents Pending Assembly TOOLS REQUIRED: 17mm and mm or equivalent wrenches. 15 26 26 16 15 16 Attach the lower mounting brackets to the Trimmer Rack poles as shown
More informationSPIRAL SLICER Instruction Manual Model #5280 & 5280M. Part No Revised Feb. 2010
SPIRAL SLICER Instruction Manual Model #5280 & 5280M Part No. 82876 Revised Feb. 2010 SAFETY PRECAUTIONS INSTALLATION INSTRUCTIONS Inspection of Shipment: 5280 & 5280M SPIRAL SLICER Unpack all cartons
More informationI N ST R UC T I ON MODELS 1612E, 1712E & 1712RE SLICERS. FORM Rev. B (10-97) 1712RE 701 S. RIDGE AVENUE TROY, OHIO 45374
I N ST R UC 1712E T I ON MODELS 1612E, 1712E & 1712RE SLICERS S ML-104546 ML-104547 ML-104548 1612E 1712E 1712RE 701 S. RIDGE AVENUE TROY, OHIO 45374 FORM 19238 Rev. B (10-97) TABLE OF CONTENTS GENERAL......................................................................
More informationTidland Series 'C' Knifeholder MAINTENANCE MANUAL Crush Cartridge Class I, II, III Crush Slitting
Tidland Series 'C' Knifeholder MAINTENANCE MANUAL Crush Cartridge Class I, II, III Crush Slitting Please read and understand all the instructions before you start to maintain the Tidland Series 'C' Knifeholder.
More informationezcinema Series Portable Floor Pull-Up Screen USER S GUIDE
ezcinema Series Portable Floor Pull-Up Screen USER S GUIDE Precautions: Warning! Screen damage can result from product mishandling if the following precautions are not followed. In accordance with practicing
More informationFancort Presents PCB Depaneling Solutions for Scored or Tab-Routed Panels
Fancort Presents PCB Depaneling Solutions for Scored or Tab-Routed Panels 11 Why select Fancort as your depaneling vendor? 1. More choices of machines for scored or routed boards 2. More factory support
More informationACCESSORY SERVICE PARTS ACCESSORY INSTALLATION INSTRUCTIONS. Covered Toilet Paper Holder. 24 Double Towel Bar 24 Double Towel Shelf
ACCESSORY INSTALLATION INSTRUCTIONS 143T 143T 143T 1431T 143T 14451T 14455T 14456T 1445T 1445T 14461T 14463T Brush Holder 1142345** Covered Toilet Paper Holder Brush Holder 24 Double Towel Bar 24 Double
More informationDIAMOND TECH INTERNATIONAL Innovations For Creativity DIAMOND LASER BAND SAW OPERATIONS MANUAL
SPEEDSTER-XL INSTRUCTION MANUAL DIAMOND TECH INTERNATIONAL Innovations For Creativity SPEEDSTER-XL DIAMOND LASER BAND SAW OPERATIONS MANUAL SPEEDSTER-XL INSTRUCTION MANUAL - PAGE 1 Before You Begin Read
More informationInstallation and User s Manual 12 x 10 MOTORIZED AWNING
12 x 10 MOTORIZED AWNING Installation and User s Manual 12 x 10 MOTORIZED AWNING 088-1763-0 Stop Please read and understand this manual before any assembly or use of this product. Before beginning assembly
More informationPRODUCT MANUAL - M096
PRODUCT MANUAL - M096 MODEL 270 ELECTRIC CAN OPENER 1 I. LABELS L087--CAUTION 2 II. SPECIFICATIONS MODEL NO. 270 POWER 115 VOLT, 1.5 AMP, 50-60HZ REQUIREMENTS 230 VOLT, 0.8 AMP, 50-60 HZ NORMAL SPEED 200-250
More informationRoller Bar End Cap (w/round Drive Shaft) Replacement Instructions for Vista and Motorized Awnings * Helpers needed *
RETRACTABLE AWNINGS For Technical Support visit us at www.sunsetter.com/ownerscorner or Call Toll Free 800-670-7071 Fax 877-224-4944 Roller Bar End Cap (w/round Drive Shaft) Replacement Instructions for
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS. Part # A7006
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS Part # A7006 Parts List Wobble Stopper Body Wobble Stopper Shaft Camper Bracket Lower Bracket Assembly Upper Bracket Upper Bracket Clamp 3/8 SAE Flat
More informationGenesis. Side Burner Accessory Installation. Step 3. Step 1. Step 2. For use with Genesis Gas Barbecues Only
Genesis Side Burner Accessory Installation For use with Genesis Gas Barbecues Only Step 1 WARNING: All gas controls and supply valves should be in the OFF position. You will need: Side burner assembly
More informationContents. Awnings USA - Full Protective Hood Manual Instructions ft 11" - 11ft 6" Awnings
Awnings USA - Full Protective Hood Manual Instructions Contents Warning We recommend that two or more people are required to lift the awning into place. 4ft 11" - 11ft 6" Awnings 8 x Expansion bolts **
More informationTuf-Lite III Fans 4000KW Series Hub
Tuf-Lite III Fans 4000KW Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 11 through 20 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass
More informationCAPRI PLUS. Instruction Manual. 28' x 38' Including sidewall and connector instructions.
CAPRI PLUS Instruction Manual 28' x 38' Including sidewall and connector instructions STOP Prior to installing any tent, always make sure you check for overhead and underground obstructions! For safe assembly,
More informationEaton ET Hydraulic Hose Saw INSTRUCTION MANUAL
Eaton ET9100-07-110 Hydraulic Saw INSTRUCTION MANUAL INSTRUCTION MANUAL Eaton ET9100-07-110 Hydraulic Saw Table of Contents Introduction... 3 Old Method... 3 New Eaton Method... 3 Operation... 4 Operation
More informationUser s Manual Trampoline 8
User s Manual Trampoline 8 Model! WARNING Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Maximum user weight 17 lbs. ASSEMBLY IMPORTANT
More informationAuxiliary 63.5l Fuel Tank Ford/Mazda Pick-up Truck 2012-Current READ ME! IMPORTANT WARNING!
Auxiliary 63.5l Fuel Tank Ford/Mazda Pick-up Truck 2012-Current ENG FTFM006 90 min READ ME! Thank you for purchasing a Front Runner Ford/Mazda Pick-Up Truck 2012 - Current Fuel Tank. Before you start,
More informationDeZURIK AM-SERIES MANUAL GEAR ACTUATOR USED ON BUTTERFLY VALVES
AM-SERIES MANUAL GEAR ACTUATOR USED ON BUTTERFLY VALVES Instruction D10501 January 2015 Instructions These instructions provide information about AM-Series Manual Actuators used on Butterfly Valves. They
More informationAND LOAD CANOPY RACK SPECIFICATIONS
8MAY15 INSTRUCTIONS for the LOCK AND LOAD CANOPY RACK SPECIFICATIONS and SAFE LOADING REQUIREMENTS The Lock and Load ladder carrier for Truck Caps is a rack designed to mount to the top of a pickup truck
More informationFORCE 10 MARINE BARBEQUES
FORCE 10 MARINE BARBEQUES PROPANE MODELS Model 3500 % Large Propane Model 3550 % Small Propane OWNER S MANUAL AND WARRANTY FORCE 10 MARINE LTD. 23080 Hamilton Road, Richmond, B.C. Canada V6V 1C9 Telephone
More informationINSTRUCTION MANUAL ALEKO RETRACTABLE AWNING
INSTRUCTION MANUAL for ALEKO RETRACTABLE AWNING www.alekoproducts.com FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY! 1 Important Safety Precautions WARNING NOTE: FOR PERSONAL SAFETY,
More informationPrimrose Awnings - Standard Manual Instructions
Primrose Awnings - Standard Manual Instructions Contents Warning 1.5m - 3.0m Awnings 4 x Expansion bolts (2 per bracket)** 2 x brackets 1 x Awning 1 x Winder handle 3.5m - 4m Awnings 6 x Expansion bolts
More informationIMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C2204A
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS C2204A Warnings Truck Bed and Camper Protection Torklift does not recommend installing your camper on top of a plastic bed liner (or other compressible
More informationFace-Bow with Quick Lock Toggle Assembly Instructions
Face-Bow with Quick Lock Toggle Assembly Instructions Whip Mix Corporation 361 Farmington Ave. P.O. Box 17183 Louisville, KY 40217-0183 USA 502-637-1451 800-626-5651 Fax 502-634-4512 www.whipmix.com Features
More informationINSTRUCTION MANUAL HYDM140
INSTRUCTION MANUAL HYDM140 INSTRUCTION MANUAL Clean-Cuts HYDM140 Hydraulic Hose Saw Table of Contents Introduction... 3 Old Method... 3 New Clean-Cuts Method... 3 Operation... 4 Operation Procedure...
More informationRUPHIS Blade Clamp. Instruction Manual
RUPHIS Blade Clamp P/N 1006800 NSN 1615-01-562-8156 Instruction Manual AH-64D UH-60A/L UH-60M S-70i S-92 REVISION AUTHORIZATION / RECORD These instructions are primarily for inspection of the RUPHIS Blade
More informationALEKO Victoria Series Retractable Awning Instructions for Installation and Operation
www.alekoproducts.com ALEKO Victoria Series Retractable Awning Instructions for Installation and Operation PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE! The owner s manual includes assembly and operating
More informationBowDown. MiniMuM Crossbar spread 24 (61CM) Steel Hook (2X) Buckle Strap (2X) Plastic Tube (2X) Plain Strap (2X) SHORT BLACK T-BOLT (2x) BOWDOWN (2x)
BowDown MiniMuM Crossbar spread 24 (61CM) Heavy Duty strap (2x) SHORT BLACK T-BOLT (2x) BOWDOWN (2x) Bow Stern Tie Down Buckle Strap (2X) Plastic Tube (2X) Plain Strap (2X) Steel Hook (2X) IMPORTANT WARNING
More informationCRD120SC TUBING CUTTER
CRD120SC TUBING CUTTER OPERATIONS MANUAL 1 VERSION 2.1 LAST EDITED 05.01.2018 cleanroomdevices.com Table of Contents Table of Contents....2 1.0 General Product & Safety Information... 3 1.1 Product Information
More informationUrea/Adblue Hose Reel
www.scintex.com.au sales@scintex.com.au Model: SHR3408 Urea/Adblue Hose Reel Product Manual Specifications Spring driven drum: for automatic rewind. Locking ratchet: to maintain the desired length of hose
More informationModel 205 Fireview Maintenance Kit
Model 205 Fireview Maintenance Kit Please read all of the instructions before you begin the procedure. Confirm that you have all the necessary tools and parts required. Allow about one hour to complete
More informationFORM Rev. A (Feb. 2004)
2812B SLICER MODEL 2912B SLICER MODEL 2912B SLICER MODEL 2912B ML-134251 ML-134252 Previous models covered by this manual: 2912B ML-134123 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com
More information* * KR54-F, KR9854 & KR9954 Installation Instructions. Read All Warnings Before Starting Installation! Index:
*941061-00* 941061-00 Keyed Removable Mullion KR54-F, KR9854 & KR9954 Installation Instructions CLASSIFIED CLASSIFIED C Read All Warnings Before Starting Installation! Index: General Information ----------------
More informationMandolin Slicer Quite possibly the safest mandolin in the world
Mandolin Slicer Quite possibly the safest mandolin in the world MANDOLIN & COMPONENTS Handle Upper Plate Safe Hands Food Holder Non-Slip Retractable Leg Julianne Blades (3 sizes) Waffle / Crinkle Cut Blade
More informationPaperfox EVV-3 Cardboard Edge Protector Cutter. Instructions manual. Last modification: 03.MAR.2018.
Paperfox EVV-3 Cardboard Edge Protector Cutter Instructions manual Last modification: 03.MAR.2018. Application of the EVV-3 Cardboard Edge Protector Cutter The EVV-3 Cardboard Edge Protector Cutter is
More informationNEWMAR SERVICE SCHOOL
NEWMAR SERVICE SCHOOL TRAINING INFORMATION GUIDELINE FOR FEBRUARY 2013 OUR PRODUCTS: NOVA DUAL PITCH AWNING G-2000/ G-1500 2 P a g e G-2085 G-5000 3 P a g e G-LINKS 4 P a g e NOVA/ G-2000/ G-1500 BASIC
More informationLVS BASE VEST OPERATOR S MANUAL
LVS BASE VEST OPERATOR S MANUAL CONTENTS 02 INTRO 04 FITTING 06 ADJUSTING SIDE-STRAPS 10 STORAGE 14 CARE 16 OPTIONAL SIDE ARMOR 20 COVERS AND ACCESSORIES This manual must be carefully read by all persons
More informationWritten By: Sam Lionheart
ipad Air Wi-Fi LCD Replacement Use this guide to replace the LCD screen in your ipad Air. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 27 INTRODUCTION Replace a damaged or nonfunctioning
More informationRetractable Awning Owner s Manual
Retractable Awning Owner s Manual TABLE OF CONTENTS SECTION-1 2 CONGRATULATIONS ON PURCHASE 2 OPERATING YOUR SHADELINE AWNING 2 GEAR CRANK OPERATION 2 EXTENDING YOUR AWNING 2 RETRACT 2 SECTION-2 3 MOTORIZED
More informationAuto Rewind Hose Reel 10M / 20M / 30M Models
Auto Rewind Hose Reel 10M / 20M / 30M Models Instruction Manual 10M / 20M / 30M Auto Rewind Hose Reel Installation, Hose Replacement and Troubleshooting Guide Product Codes: 1110H / 1120H / 1130H Models
More informationKAWASAKI MULE 610 WINCH MOUNT KIT. Owner s Manual
1701 38TH AVE W PO BOX 257 SPENCER, IA 51301 PHONE: 712-262-4191 FAX: 712-262-0248 SERVICE: 800-841-2222 E-MAIL: ccac@cyclecountry.com KAWASAKI MULE 610 WINCH MOUNT KIT Owner s Manual MODEL NUMBER: 25-2200
More informationPhantom Retractor System Overview
Spine Phantom Retractor System Overview Minimally invasive procedures Dual-directional expandable retractor 30 degree pivoting blades Fiber-optic light source for better visualization Key Design Features
More informationS E L E C T I O N. Abdominal Crunch. User manual
and S E L E C T I O N T H E S T R E N G T H E V O L U T I O N User manual and and The identification plate of the and manufacturer, affixed along side the seat on the frame of the weight stack, gives the
More informationAdvantage Plus TIM-3600 Series Reel
Read the following precautions and instructions before you begin assembly or using. Failure to comply with these instructions could result in personal injury or property damage. Keep these instructions
More informationMotorized retractable awning
Motorized retractable awning Model 95295 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly
More informationTHE EDGE12 SLICER. MODEL EDGE12-2 (220/50/1 voltage) FORM (July 2012) EDGE12 SLICER
EDGE12 SLICER THE EDGE12 SLICER MODEL EDGE12-1 (120/60/1 voltage) EDGE12-2 (220/50/1 voltage) ML-136246 ML-136247 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 35283 (July
More informationWritten By: Arthur Shi
ipad 5 LTE LCD Replacement Follow this guide to replace the LCD screen in an ipad 5 LTE. Written By: Arthur Shi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Use this guide to replace the
More informationPLATINUM MODEL WITH AUTO-RETRACT AND REMOTE CONTROL. Owner s Manual
PLATINUM MODEL WITH AUTO-RETRACT AND REMOTE CONTROL Owner s Manual THIS MANUAL CONTAINS INSTRUCTIONS FOR UPGRADING BOTH THE GOLD MODEL ONE-TOUCH AND THE ONE-TOUCH MODEL WITH THE KEY SWITCH TO THE PLATINUM
More informationMotorized Oasis Awning RTS Motor Cord Replacement Instructions *Helpers Needed*
RETRACTABLE AWNINGS For Technical Support visit us at www.sunsetter.com/ownerscorner or Call Toll Free 800-670-7071 Fax 877-224-4944 Motorized Oasis Awning RTS Motor Cord Replacement Instructions *Helpers
More informationGoBidet Bidet Attachment
GoBidet Bidet Attachment 151 Ruths Place #5 Sequim, WA 98382 Tel 1-800-681-0753 Fax +1 360-681-4029 www.go-bidet.com MODEL #2003C In this box: 1 User Manual 1 GoBidet Unit w/ mounting bracket, nut, rubber
More informationJARVIS. Model 70 Airsnip Air Powered Scissors
Air Powered Scissors EQUIPMENT SELECTION... Ordering No. Airsnip Model 70... 4019009 Air Filter/Regulator/Lubricator.. 3022003 Balancer... 1350084 Power--Pak (250 PSI)... 4026016 TABLE OF CONTENTS... Page
More informationMeat Slicer INSTRUCTION MANUAL CAUTION! ONE YEAR LIMITED WARRANTY
ONE YEAR LIMITED WARRANTY INSTRUCTION MANUAL The original registered owner of this product should contact SKYFOOD EQUIPMENT LLC at 305-868-16 for any warranty problems or service. SKYFOOD EQUIPMENT LLC
More informationTN5000 Titan Manual Rotary Microtome
User Manual TN5000 Titan Manual Rotary Microtome Read Prior to Operation! Always keep this manual near the unit! WP47617 06.02.15 User Manual TN5500: Titan 888.708.5233 Info@TannerScientific.com www.tannerscientific.com
More informationAll Restoration Hardware beds are designed to meet the highest safety standards and comply with all U.S. and Canadian beds and beds regulations.
All Restoration Hardware beds are designed to meet the highest safety standards and comply with all U.S. and Canadian beds and beds regulations. Made in India Distributed in the USA by Restoration Hardware
More information3D Printed Glider instructions
3D Printed Glider instructions For more cool designs, check out threedsy.com! Printing Instructions: ABS or PET is preferred for durability. Bed must be leveled and printer adjusted to produce good single
More informationWHAT TO KNOW BEFORE INSTALLING...
WL600922H WL601022H WL601122H WL502086H WL602376H WL602322H Please read the information sheet before proceeding. WHAT TO KNOW BEFORE INSTALLING... 1. 2. When positioning the seat onto the pan ensure that
More informationPARTS LIST COLT COLT HEPA
PARTS LIST COLT 800-1250 - 1450 COLT HEPA - 1250-1450 MOTOR / LID ITEM PART NO. PART DESCRIPTION QTY. 101 0891201 TOP COVER 1 102 0294341 TOP MOTOR SEAL 1 103 0299861 STRAIN RELIEF CORD CLAMP 1 104 0891131
More informationINSTALLATION SHEET. PARTS INCLUDED IN YOUR KIT. You may want to lay them out in this manner for accessibility.
INSTALLATION SHEET Gas Struts (x2) Lower Hinge Rail Side Rails (L and R) Spring Bows (x2-short Bed) (x3-long Bed) L Bars (L and R) with clamps included L Channel w/seal MISSING PARTS??? Call Extang at
More informationMYRIAD Banner Stand is a trademark of Skyline Exhibits. Patent Pending PN32294-B. MYRIAD Banner Stand
is a trademark of Skyline Exhibits Patent Pending 1.1 1. Banner Stand Setup 1.1 Remove banner stand from standard case or Arrive Portable Display & Workstation and assemble pole. 1.2 Insert pole into base
More informationPLATINUM MODEL WITH AUTO-RETRACT AND REMOTE CONTROL. Owner s Manual
PLATINUM MODEL WITH AUTO-RETRACT AND REMOTE CONTROL Owner s Manual THIS MANUAL CONTAINS INSTRUCTIONS FOR UPGRADING BOTH THE GOLD MODEL ONE-TOUCH AND THE ONE-TOUCH MODEL WITH THE KEY SWITCH TO THE PLATINUM
More informationGas Go Anywhere /23/01
Gas Go Anywhere 55014 02/23/01 FOR OUTDOOR USE ONLY This grill does not include an LP fuel tank. Check Package Contents You should have received the parts listed below. While we give much attention to
More informationINSTRUCTION SHEET DETHATCHER KIT. STS-422LX LPSTS-42JD Assembly Installation Operation Repair Parts L-1660-D. Visit us on the web!
INSTRUCTION SHEET DETHATCHER KIT MODEL: DK-422LX FOR USE WITH SWEEPER MODEL: STS-422LX LPSTS-42JD Assembly Installation Operation Repair Parts For use with Riders and Lawn/Garden Tractors For the latest
More informationINSTALLATION INSTRUCTIONS TOWNSEND
INSTALLATION INSTRUCTIONS TOWNSEND.00 DECK MOUNT BATH FILLER.0 Thank you for selecting American Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-please
More informationASSEMBLY & CARE INSTRUCTIONS
ASSEMBLY & CARE INSTRUCTIONS 7 x TRAILER TENT SERIES 3 9 Part No. FT3711 - on road FT3923 - off road OPTIONAL SUNROOM Wall and floor kit Part No. FT3723 - on road FT39 - off road OPTIONAL SPARE ROOM Roof,
More informationEaton ET Hydraulic Hose Saw INSTRUCTION MANUAL
Eaton ET9200-10-220 Hydraulic Hose Saw INSTRUCTION MANUAL INSTRUCTION MANUAL Eaton ET9200-10-220 Hydraulic Hose Saw Table of Contents Introduction... 3 Old Method... 3 New Eaton Method... 3 Operation...
More informationTUCSON PATIO AWNING INSTALLATION MANUAL
TUCSON PATIO AWNING INSTALLATION MANUAL Toll Free 877-792-1775 Fax 877-792-0031 swsuncontrolpro.com sales@swsuncontrol.com 1 INTRODUCTION...3 1.1 Symbols used in this manual... 3 1.2 Personnel requirements...
More informationIMPORTANT NOTICE. Professional Mandoline Manual
IMPORTANT NOTICE PLEASE DO NOT RETURN TO STORE. If you have any problems with this unit, contact Consumer Relations for service. PHONE: 206-605-0555 Please read operating instructions before using this
More informationINSTRUCTION 7510,7512 MANUAL. DURO SERIES Slicer 7510/12/1099 ED7 WE THANK YOU FOR YOUR PURCHASE OF OUR MODEL 7510, 7512 SLICER.
INSTRUCTION 7510,7512 MANUAL DURO SERIES Slicer WE THANK YOU FOR YOUR PURCHASE OF OUR MODEL 7510, 7512 SLICER. SINCE 1948 7510/12/1099 ED7 TABLE OF CONTENTS DESCRIPTION PAGE Table of Contents 1 List of
More information33100 LH - Batwing Awning RH - Batwing Awning
33100 LH - Batwing Awning 33200 RH - Batwing Awning 1. Check Part No./Kit is correct 3. Fit roof rack accessory 2. Read through instruction before installing 4. Check and recheck all fasteners are secure
More informationInstallation Instructions for Wall Mount, Deck Mount and Pre-rinse Faucets
Installation Instructions for Wall Mount, Deck Mount and Pre-rinse Faucets SAVE FOR END USER ELKAY 2222 CAMDEN COURT OAK BROOK, IL 60523 USA WALL MOUNT ASSEMBLY General Instructions Turn off the water
More informationAlien Flier Zip Line Products Installation/Owner s Manual
Alien Flier Zip Line Products Installation/Owner s Manual 1 Table of Contents SAFETY PLEASE READ CAREFULLY... 4 Constructing your Zip Line Xtreme Models... 6 Installing your Alien Flier Trolley on an Existing
More informationStonefire Fire Pit Table. Installation Instructions for SF-32-K
Stonefire Fire Pit Table Installation Instructions for SF-32-K / 1 2 IMPORTANT Please consult your Crystal Fire instruction manual for detailed instructions and important information related to the burner
More informationHINGES & STAYS. Hinges & Stays Large Take-Apart Hinge. Medium Take-Apart Hinge
Hinges & Stays HINGES & STAYS TAKE-APART-CONTINUOUS-WELD-ON-CONCEALED-STRAP-STOP-BUTT-OFFSET-LIFT-OFF-STAY 0.1 0-180800.0 Mat: Steel Finish: Zinc Plate Wt:.0kg /.1lbs.8. Acts as a hinge but allows quick
More informationINSTALLATION INSTRUCTIONS for folding arm awnings
Custom made Awnings and Blinds Item No 0757 INSTALLATION INSTRUCTIONS for folding arm awnings IMPORTANT INFORMATION BEFORE INSTALLING YOUR Updated 08/09/15 AN AWNING INSTALLATION IS A HOME IMPROVEMENT
More information