FOREWORD CONTENTS. 1. Preparation and tools required for assembly. 2. Complete parts
|
|
- Annabella Brooks
- 5 years ago
- Views:
Transcription
1 CONNECTOR ASSEMBLY INSTRUCTION MANUAL
2 FOREWORD Thank you for purchasing FOCI s MT-RJ Optical Fiber Connectors. We are confident that our excellent manufacturing procedures and stringent quality control guarantee you have purchased a product that will provide many years of trouble-free service. By following the simple step-by-step assembly instructions and with competent polishing, you will be able to produce fiber terminations of high stability, featuring low insertion loss and low back reflection loss. This manual describes the assembly procedure of the P-CM-FX-02 & P-CM-MX-02 type connectors. We strongly advise careful reading of this entire manual before commencing assembly and use of this product. CONTENTS 1. Preparation and tools required for assembly 2. Complete parts 3. Step-by-step instructions a) Cable preparation b) Ferrule termination c) MT-RJ housing assembly 1. PREPARATION: a) Ensure the work surface is clean and dust-free with good lighting b) Assemble all necessary tools and equipment: Connector assembly tools: (from top to bottom, left to right) Shears PVC stripper Fiber stripper Sharp scissors Crimper Crimper
3 2. COMPLETE PARTS: Parts for FOCI MT-RJ connector (from left to right) Dust cover Body, connector Pin keeper Ferrule (MM) Ferrule, Boot, Spring Spring push Crimp eyelet Boot 3. STEP-BY-STEP ASSEMBLY INSTRUCTIONS: A: Cable preparation A.1 Insert firstly the boot (10) and then the crimp ring (9) onto the cable. A.2 Remove the cable jacket with the PVC stripper (1.3mm) according to the length as shown in the diagram below
4 A.3. Trim kevlar with shears to within 5 millimeters of the jacket using shears. A.4. Use sharp scissors to separate the 4 fibers of the ribbon cable. A.5.a) If you are using ribbon fiber, remove the middle two fibers as close as possible to the ribbon matrix material. Then strip the plastic and coating off the two outer fibers. A.5.b) If you are using FOCI duplex MTRJ cable, simply strip the plastic coating off the fibers to a length of 5mm. A.6. Clean the bare fiber strands with a lint-free wipe and alcohol to remove any coating residue.
5 A.7. Carefully slide the spring push over the fibers and over the kevlar ensuring that it gathers all the kevlar stands and holds them neatly out of the way. Slide the spring over the fibers up to the spring push. B. MT-RJ Cable Termination B.1. Using a clean toothpick, place a small drop of epoxy on the fibers. Spread evenly. B.2. Insert the ferrule boot into the back end of the ferrule until it stops.
6 B.3. Determine which edge of the ribbon is the #1 fiber. (Typically the #1 fiber is colored blue.) Take the MT-RJ ferrule and locate the #1 fiber side, then with the proper fiber orientation in the ferrule, carefully insert the fibers into the rear of the ferrule. The fibers should slide into the holes and pass smoothly through the ferrule end-face. If any resistance is felt, back the fiber out slightly and try again, watching through the window to ensure that both fibers are in the proper track. Any bending of a fiber signifies misalignment and may cause fiber breakage. B.4. Look into the ferrule window and make sure the edgeof the ribbon matrix is located betweek the back edge of the ferrule window and the step marking the end of the grooves. CAUTION: Pushing the edge of the ribbon matrix past the step and onto the grooves may cause the fibers to break. This problem is negated when using FOCI duplex MT-RJ cable. B.5. Using a toothpick, place a small drop of epoxy into the ferrule window and also into the holes on the ferrule end-face to form a small bead around the protruding fibers. B.6. Place the ferrule into the ferrule heater. Recheck the epoxy level in the window and add if necessary (some settling may occur due to the epoxy spreading to fill the cavity). Be careful not to overfill the cavity as excess epoxy must be removed after curing.
7 B.7. After curing, remove the ferrule from the oven and allow to cool. Break the fibers that protrude from the ferrule with carbide scribe. NOTE: Connectors are assembled as male or female type plugs. Male plugs have a pin guide with guide pins pre-installed, while female plugs have a pin clamp without guide pins. If assembling male connectors, ferrules must first be polished before completing MT-RJ housing assembly. C. MT-RJ Housing Assembly C.1. For female connectors: Take a female pin clamp and position it on the ribbon. Push the clamp over the ferrule boot securely against the rear of the ferrule. Slide the spring against the clamp and apply a slight pressure with the spring in order to hold it in place. Note: The pin clamp is not necessary if FOCI duplex MT-RJ cable is used. C.1. For male connectors: Obtain a male pin clamp and position it on the ribbon. Insert the guide pins into the holes in the rear of the ferrule. It is important for the pin clamp to sit securely against the ferrule rear in order for the housing to assemble properly. Slide the spring against the clamp.
8 C.2. Align the housing with the window side of the ferrule facing towards the latch of the connector, then slide the connector housing onto the ferrule until a click is heard as the spring push inserts into the housing. C.3. Using a clean toothpick or tweezers, pull the kevlar strands from underneath the spring push. C.4. Slides the crimp ring over the cable jacket ensuring at the kevlar strands are held between the crimp ring and the rear of the spring push. The crimp ring should be pushed all the way up to the spring push. C.5. Using the crimping tool (mm), crimp the large upper ring around the kevlar and spring push, then crimp the small lower ring around the cable jacket with the mm crimping hole. C.6. Slide the connector boot up over the crimp ring.
Applications Engineering Notes
Applications Engineering Notes Document Title Document Number MTP Brand Connector Installation Onto AEN-1401 Revision Number 2.1 Effective Date November 15, 2011 THE USE OF SAFETY GLASSES FOR EYE PROTECTION
More informationApplications Engineering Notes
Applications Engineering Notes Document Title Document Number MTP Brand Connector Installation Onto 3.0 mm Jacketed Round Cable With Loose Fibers AEN-1407 Revision Number 2.1 Effective Date November 15,
More informationApplications Engineering Notes
Applications Engineering Notes Document Title Document Number MTP Brand Connector Installation Onto AEN-1420 Revision Number 1.1 Effective Date January 17, 2017 THE USE OF SAFETY GLASSES FOR EYE PROTECTION
More informationTermination Procedure LC 1.6mm & 2.0mm Connectors: 1060XX Series
Connector Piece Parts LC Simplex Connector Boot LC Duplex Connector LC Connector CriMp Tulolng LC Duplex Clip Boot 86001-0110, Rev. B USN30MFO/5/2010 Procedure Chart Procedure Tool Required Tool Part Number
More informationCrimp & Cleave Termination Instructions for 200 µm F07 Connectors
Your Optical Fiber Solutions Partner Crimp & Cleave Termination Instructions for 200 µm F07 Connectors For Use With: F07 Termination Kits 200 µm HCS Fiber-Optic Cable F07 Crimp & Cleave Connectors Important
More informationCrimp & Cleave Termination Instructions
Your Optical Fiber Solutions Partner Crimp & Cleave Termination Instructions for 200 µm Harsh Environment SMA For Use With: 200 µm HE SMA Termination Kit 200 µm HCS Fiber-Optic Cable HE SMA 200 µm Crimp
More informationQWIK MPO Termination Instructions
Instruction Sheet 860532050 QWIK MPO Termination Instructions General The CommScope QWIK MPO Termination Kit and Connector Kit, with the Splicer Kit (ordered separately) facilitate the proper termination
More informationCrimp & Cleave Termination Instructions
A Furukawa Company Your Optical Fiber Solutions Partner Crimp & Cleave Termination Instructions for 200 µm and 400 µm ST and SMA Connectors For Use With: 200 µm and 400 µm ST and SMA Termination Kits 200
More informationCrimp & Cleave Termination Instructions
Crimp & Cleave Termination Instructions for 200 µm Factory5 Cable with ST and SMA Connectors For Use With: 200 µm ST and SMA Factory5 Termination Kits 200 µm HCS Factory5 Fiber-Optic Cable ST and SMA Factory5
More informationCrimp & Cleave Termination Instructions for 200 µm Factory5 Cable with ST and SMA Connectors
Your Optical Fiber Solutions Partner Crimp & Cleave Termination Instructions for 200 µm Factory5 Cable with ST and SMA Connectors For Use With: 200 µm ST and SMA Factory5 Termination Kits 200 µm HCS Factory5
More informationCrimp & Cleave Termination Instructions for 200 µm Harsh Environment SMA
Your Optical Fiber Solutions Partner Crimp & Cleave Termination Instructions for 200 µm Harsh Environment SMA For Use With: 200 µm HE SMA Termination Kit 200 µm HCS Fiber-Optic Cable HE SMA 200 µm Crimp
More informationCOMPONENT IDENTIFICATION
Panduit Corp. 2006 MINI-COM FJ OPTI-CRIMP Standard and Keyed Multimode Duplex Fiber Optic Jack Modules Part Numbers: FJJSMM5C***, FJJSMM50C*** READ ALL INSTRUCTIONS COMPLETELY BEFORE PROCEEDING COMPONENT
More informationInstructions. Fibrlok TM 2670 Multi-Fiber Ribbon Construction Tool. November, B
Instructions Fibrlok TM 2670 Multi-Fiber Ribbon Construction Tool November, 1998 34-7032-7181-6-B Contents: 1.0 General... 3 2.0 Ribbon Construction Tool Kit...3 3.0 Preparing the Fibers...3 4.0 Arranging
More informationCOMPONENT IDENTIFICATION
ST Opti-Crimp Multimode Fiber Optic Connector Part Numbers: FSTMM**, FSTMM50** Panduit Corp. 2014 INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS COMPLETELY BEFORE PROCEEDING COMPONENT IDENTIFICATION CONNECTOR
More informationSLCS-P1UA, SLCS-PN1UA Series Ø0.9mm LC Universal Splice-On Connector
DOCUMENT NUMBER S05-K027-01E SLCS-P1UA, SLCS-PN1UA Series Ø0.9mm LC Universal Splice-On Connector ASSEMBLY MANUAL Fiber Optic Products Division 296-1, MATSUHIDAI, MATSUDO-SHI, CHIBA, 270-2214 JAPAN. TEL:
More informationCOMPONENT IDENTIFICATION
LC Fiber Optic Connectors Field Polish Termination - Singlemode and Multimode Panduit Corp. 2017 INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS COMPLETELY BEFORE PROCEEDING COMPONENT IDENTIFICATION CONNECTOR
More informationFC TYPE CONNECTOR ACCESSORIES ST TYPE CONNECTOR ACCESSORIES
ET ELECOM PARTS FC TYPE CONNECTOR ACCESSORIES 3 Stoping Ring 2 1 Coupling Nut Plug Frame 1 CA-FC-304 Zinc Alloy Nickel Plating 2 CA-FC-CN Zinc Alloy Nickel Plating 3 CA-FC-303 Zinc Alloy Nickel Plating
More informationKITS P /2/01 4:40 pm Page 29 Kits 29 #
29# Kits Clip-On Twisted Pair Kit The Clip-On Twisted Pair Kit combines the most commonly used tools for terminating voice and data cabling into an easy to carry kit that mounts on the contractor s belt.
More information1. COMPONENT IDENTIFICATION
MINI-COM OPTI-JACK FJ Fiber Optic Connectors Field Polish Termination - Singlemode and Multimode Part Numbers: FJJGM5C, FJJGM2.0C, FJEPGM5C, FJEPGM2.0C, FJJGS9CBUY, FJJGS2.0CBUY, FJEPGS9CBUY, FJEPGS2.0CBUY
More informationCOMPONENT IDENTIFICATION
LC Fiber Optic Connectors Field Polish Termination - Singlemode and Multimode Panduit Corp. 2014 INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS COMPLETELY BEFORE PROCEEDING COMPONENT IDENTIFICATION CONNECTOR
More informationTOOLS TOOLS. Chapter Summary All the tooling required to terminate optical fiber and twisted pair connectors
TOOLS Tools Fiber Optic Tool Kits......................... 170-173 Epoxies and Accessories...................... 173-175 Microscopes................................ 176-177 Fiber Optic Tools and Accessories...............
More informationAmphenol RF Interconnects TNC 31 Series Threaded Lock RF Connector System Materials
TNC 31 Series Threaded Lock RF Connector System Materials Body/Finish Contacts Centre MALE Centre FEMALE Insulator Gasket Crimp Ferrules* *Metal finishes Durability Brass/Nickel Brass/Gold Plated (Au)
More informationApplication Tooling Specification
Order No. 200218-3100 FEATURES Application Tooling Specification A full cycle ratcheting hand tool ensures complete crimps Long handles for comfortable crimping with reduced crimping force and a safety
More information1. COMPONENT IDENTIFICATION
SC Fiber Optic Connectors Field Polish Termination - Singlemode and Multimode Panduit Corp. 2014 INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS COMPLETELY BEFORE PROCEEDING 1. COMPONENT IDENTIFICATION
More informationCorning Cable Systems Enhanced FuseLite Termination System
Corning Cable le Systems Enhanced FuseLite Termination System Instruction Manual Corning Cable Systems reserves the right to improve, enhance, and modify the features and specifications of Corning Cable
More informationSYSTIMAX RoloSplice Multiple Splice Organizer Installation
SYSTIMAX RoloSplice Multiple Splice Organizer Installation General This instruction sheet provides procedures for installing the SYSTIMAX RoloSplice, multiple splice organizer management system and is
More informationWritten By: Arthur Shi
ipad 5 LTE LCD Replacement Follow this guide to replace the LCD screen in an ipad 5 LTE. Written By: Arthur Shi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Use this guide to replace the
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. One-piece connector body: Fastest assembly Field installable Anaerobic epoxy
More informationOtter Pro XT Cabin Installation and Set-Up Instructions
Otter Pro XT Cabin Installation and Set-Up Instructions Otter Pro XT Cabin Fits Medium Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro XT Thermal Cabin
More informationGo4Fiber Tool Kit (Contractor / Basic / Splice / Connectorization)
Go4Fiber Tool Kit (Contractor / Basic / Splice / Connectorization) 01 Go4Fiber focuses on the quality as well as the performance of the kit instead of just putting together economical items to reduce cost.
More informationWritten By: Sam Lionheart
ipad Air Wi-Fi LCD Replacement Use this guide to replace the LCD screen in your ipad Air. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 27 INTRODUCTION Replace a damaged or nonfunctioning
More informationOptical Connector Termination Tool CAK-0057-EX. Instruction Manual SUMITOMO ELECTRIC INDUSTRIES, LTD.
Technical Information KOUTURIGISHI-1078H Optical Connector Termination Tool CAK-0057-EX Instruction Manual 2011-03-16 SUMITOMO ELECTRIC INDUSTRIES, LTD. The information contained herein is presented only
More information$ Die Set, Fibersure Crimper, Universal HEX, 5-Cavity. $ Die Set, Fibersure Crimper, Lucent STII $29.98 $29.
Part # Description MSRP 0100-1520 Strip Template, Corning LC Connectors $1.50 0100-1560 Strip Template, Senko/Molex LC Connectors $1.50 0100-2010 Instruction Manual $7.50 0200-2410 ST Opticon MM Connector,
More informationSECTION 11 TABLE OF CONTENTS
Contents Inspection and Cleaning Features and Benefits...11-2 Standards...11-2 Product Range Overview...11-4 LuxCis ARINC 801 Inspection and Cleaning Kits...11-5 Inspection Assistant Kits for LuxCis ARINC
More informationBARE FIBER OPTIC TERMINATOR
BARE FIBER OPTIC TERMINATOR Reusable Terminator for Single Mode and Multimode Fiber FC/PC, FC/APC, SMA905, ST /PC, SC/PC, or LC/PC Compatible Connectors Terminator Accepts Bare Fiber up to Ø1400 µm Application
More informationAccu-Tech DIR Discount: 10.75%
0100-1520 Strip Template, Corning LC Connectors $1.00 0100-1560 Strip Template, Senko/Molex LC Connectors $1.00 0100-2010 Instruction Manual $5.00 0200-2410 ST Opticon MM Connector, 2 boots (900um/3mm)
More informationAssembly Instructions - TSK
Assembly Instructions - Please read these instructions once completely before beginning with the individual steps. General Note Required Experience for the construction of gabions have to be the following
More informationipad mini 4 LTE Home Button Assembly Replacement
ipad mini 4 LTE Home Button Assembly Replacement Replace the home button assembly in an ipad mini 4 LTE. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION Follow the
More informationInstruction for edge trimming knife sharpening of M-Type shoe sewing machines
Instruction for edge trimming knife sharpening of M-Type shoe sewing machines 1. Introduction This instruction is a supplement to the instruction for use of electric table sharpener; thus the scope of
More informationMYRIAD Banner Stand is a trademark of Skyline Exhibits. Patent Pending PN32294-B. MYRIAD Banner Stand
is a trademark of Skyline Exhibits Patent Pending 1.1 1. Banner Stand Setup 1.1 Remove banner stand from standard case or Arrive Portable Display & Workstation and assemble pole. 1.2 Insert pole into base
More informationOtter XT Cabin Installation and Set-Up Instructions
Otter XT Cabin Installation and Set-Up Instructions Otter XT Cabin Fits Medium Otter Wild Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Otter XT Cabin 200962 2 1 PARTS LIST
More informationInsulated Scissors. Handles made with shock-proof plastic. Length Blade Std. Part No. Type mm shape Pk.
Cutting Tools Cable Cutter - For copper and aluminum cables only. Extremely high cutting capacity with adjustable screw joint. for cable Length Std. Part No Type Ømm mm 2 AWG mm Pk. AP1017 N 15 50 1/0
More informationSERVICE MANUAL- M126
SERVICE MANUAL- MANUAL CAN OPENER- MODEL # 2 1 Model #2 Can Opener Assembly Procedure The Model #2 can opener will be assembled according to the following procedure. I. Model #2 Handle and Arbor Assembly
More informationOtter XT 650 Cabin Installation and Set-Up Instructions
Otter XT 650 Cabin Installation and Set-Up Instructions Otter XT 650 Cabin Fits Medium Otter Wild Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Otter XT 650 Cabin 200891 2 1
More informationModel 205 Fireview Maintenance Kit
Model 205 Fireview Maintenance Kit Please read all of the instructions before you begin the procedure. Confirm that you have all the necessary tools and parts required. Allow about one hour to complete
More informationReverse Osmosis system 50 GPD Instruction manual EN
Reverse Osmosis system 50 GPD Instruction manual EN Contents 1. Unpacking 2. Scope of supply 3. Insertion of the membranes 4. Connecting the lines 5. Installation 6. First commissioning 7. Consumables
More informationipad mini 4 Wi-Fi Volume Control Buttons Replacement
ipad mini 4 Wi-Fi Volume Control Buttons Replacement Replace the volume control buttons in an ipad mini 4 Wi-Fi. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 21 INTRODUCTION Use
More informationWenger Corporation 2014 Printed in USA 05/14 Part #049B015-09
Assembly Instructions Tuba Tamer Contents Important User Information...........................2 Replacemant Parts List..............................3 Assembly.........................................4
More informationSERVICE PARTS LIST AND ASSEMBLY INSTRUCTIONS
R Transport Air Conditioning FlexCLIK 58-64105-03 #12 [16MM], 35 Bar, SAE J2064 Type E FlexCLIK 58-64105-02 #10 [13MM], 35 Bar, SAE J2064 Type E FlexCLIK 58-64105-01 #8 [10MM], 35 Bar, SAE J2064 Type E
More informationOtter Pro XT 1200 Cottage Installation and Set-Up Instructions
Otter Pro XT 1200 Cottage Installation and Set-Up Instructions Otter Pro XT 1200 Cottage Fits Small Ultra-Wide Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete
More informationProduct instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E
Product instruction manual Ream Cutting Systems RE3943, RE3946, RE3947, RE3971, RE3952E The Trimfast Ream Cutters are reliable, high performance cutters that will give you the results you need quickly
More informationAgilent Ultimate Union Kits (G and G )
Agilent Ultimate Union Kits (G3182-61580 and G3182-61581) Installation Guide The Agilent Ultimate Union (Figure 1) provides a high performance, easy to maintain connection method for capillary columns.
More informationOne Piece Low Torque Kelly Valve. Preventive Maintenance Service Video Disassembly and Assembly Procedures
One Piece Low Torque Kelly Valve Preventive Maintenance Service Video Disassembly and Assembly Procedures Global Manufacturing, Inc. Lafayette, Louisiana USA 70508 Ph (337) 237-1727 Fax (337) 232-9353
More informationFERRULES & TOOLS Altech Corp. 35 Royal Road Flemington, NJ Phone (908) FAX (908)
TerminalBlocks_072012(alt-2).QD_Blocks 10/23/12 9:05 AM Page 117 To help you do the best job possible when using Altech s terminal blocks, we put together a selection of useful tools to accomplish just
More informationUniCam Pretium -Performance Multimode Connectors: LC, SC, ST Compatible
features and benefits Corning Cable Systems UniCam Pretium - Broad operating temperature (-40 to +75 C) Factory-polished end-face Fast termination and no consumables Minimum insertion loss Utility and
More informationMaintaining the Pretium FBC-015 Cleaver
Maintaining the Pretium FBC-015 Cleaver The FBC-015 cleaver utilizes a unique handheld design that provides high quality cleaves that enable the outstanding performance of Corning UniCam connectors. In
More informationipad mini 4 Wi-Fi Display Assembly Replacement
ipad mini 4 Wi-Fi Display Assembly Replacement Replace the display assembly, including the LCD screen, home button, and front glass digitizer in an ipad mini 4 Wi-Fi. Written By: Evan Noronha ifixit CC
More informationFiber Optic Hand Tools
Fiber Optic Hand Tools Miller Fiber Optic Hand Tools FO 103-T-250-J Tri-Hole Fiber Optic Stripper New three-hole model performs all common fiber stripping functions in one compact tool. Hole for removal
More informationPLEASE READ BEFORE USE AND SAVE THESE INSTRUCTIONS
Sauce Flip Pan PLEASE READ BEFORE USE AND SAVE THESE INSTRUCTIONS Thank you for purchasing Cook s Companion Sauce Flip Pan. This pan is designed to be one of the most used pans in your kitchen. The Fusion
More informationSealing and terminating Wrexham Mineral Cables
Sealing and terminating Wrexham Mineral Cables A Termination is required at both ends of each length of cable, and it should be fitted as soon as the cable has been prepared. A complete termination consists
More informationOperating Instructions
A) ORIENTATION View capsule filling video online at www.profiller.com Cam Lever 1. Place Caps Tray onto Filler with Position I and II markings in front. Check that Cam Lever is set to 3 o clock. 2. Pour
More informationAB KNOCK-DOWN WATER BOILER
FORM 2344 3/25/2004 AB KNOCK-DOWN WATER BOILER TABLE OF CONTENTS Description Page KNOCK-DOWN TYPES AND DEFINITIONS 1 BOILER FOUNDATION 1 BOILER FRAME & TUBE INSTALLATION 2 BASE PAN INSULATION 4 TUBE BAFFLE
More informationProGrip 5-in-1 Fibre Optic Stripper. ProGrip 3-in-1 Fibre Optic Stripper. Pro-Plus Wire Stripper. Tools for Fibre.
Tools for Fibre www.greenleecommunications.com ProGrip 5-in-1 Fibre Optic Stripper Precision ground stripping cavities for: 2.0-2.4mm outer jacket 2.0-3.0mm loose tube 2.8-3.0mm outer jacket 900μm buffer
More informationTwo Piece Low Torque Kelly Valve
Two Piece Low Torque Kelly Valve Disassembly and Assembly Procedures Global Manufacturing, Inc. Lafayette, Louisiana USA 70508 Ph (337) 237-1727 Fax (337) 232-9353 SAFETY CONSIDERATIONS Safety glasses
More informationELE-3COP-375 Title - Braid termination using a Band Strap Adaptor.
Before starting work please read this document carefully and note the guidance given. 1 Purpose and Scope This COP describes the procedure to be used when carrying out the installation of a Band Strap
More informationDO NOT USE WITH CROSSBAR SPREAD LESS THAN 24.
TM Please read all instructions carefully before assembly, installation and/or use of this product. DO NOT USE WITH CROSSBAR SPREAD LESS THAN 24. WARNING: Do not exceed the weight limit of your vehicle
More informationS E L E C T I O N. Abdominal Crunch. User manual
and S E L E C T I O N T H E S T R E N G T H E V O L U T I O N User manual and and The identification plate of the and manufacturer, affixed along side the seat on the frame of the weight stack, gives the
More informationMandolin Slicer Quite possibly the safest mandolin in the world
Mandolin Slicer Quite possibly the safest mandolin in the world MANDOLIN & COMPONENTS Handle Upper Plate Safe Hands Food Holder Non-Slip Retractable Leg Julianne Blades (3 sizes) Waffle / Crinkle Cut Blade
More informationOtter Pro X-Over Lodge Installation and Set-Up Instructions
Otter Pro X-Over Lodge Installation and Set-Up Instructions Otter Pro X-Over Lodge Fits Magnum Otter II & Pro Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro X-Over Lodge
More informationFISH CAT SCOUT OWNER S MANUAL
FISH CAT SCOUT OWNER S MANUAL ALWAYS WEAR A COAST GUARD APPROVED FLOTATION DEVICE WHEN OPERATING THE FISH CAT SCOUT. Know the limits of your abilities and the limits of your equipment. Changes in air temperature
More informationMODEL # 1 MANUAL CAN OPENER
REV.B SERVICE MANUAL MODEL # 1 MANUAL CAN OPENER Model #1 Can Opener Assembly Procedure The Model #1 can opener will be assembled according to the following procedure. I. Model #1 Handle and Arbor Assembly
More informationM129 SERVICE MANUAL- M129 MODEL #G-2 MANUAL CAN OPENER
SERVICE MANUAL- M129 MODEL #G-2 MANUAL CAN OPENER Model #G-2 Can Opener Assembly Procedure The Model #G-2 can opener will be assembled according to the following procedure. I. Model #G-2 Handle and Arbor
More informationCeramic Probe Replacement Instructions Accessory G
Ceramic Probe Replacement Instructions Accessory G6600-60035 Purpose The Stainless Burner has two ceramic combustion tubes, which require periodic replacement: an inner and an outer tube. Scope This procedure
More informationPR-429BF-600M. Bell 429 Blade Fold Kit Operations Manual
Table of Contents Table of Contents... 1 Record of Revisions... 2 References... 3 Introduction... 4 Contact Information... 4 Prerequisites... 5 First Time Use... 6 Blade Clamp Placement... 6 Blade Clamp
More informationGT371 HEDGETRIMMER TYPE
GT371 HEDGETRIMMER TYPE 1 Introduction Exploded Drawing Bill Of Material Repair Instructions E13791 GT371-----A New Parts Wiring Diagram Main Menu 3 18 02-04 SEAN HOLDEN GT371 MANUFACTURING PLANT USTI
More information2522 and 2523 Fiber Optic Splice Organizer Tray
2522 and 2523 Fiber Optic Splice Organizer Tray Instructions February 1996 Issue 1, 34-7039-6256-2 1 Table of Contents 1. General... 3 2. Kit Contents... 3 3. Available Kits and Accessories... 4 4. Tray
More informationThomas Scientific Swedesboro, NJ U.S.A.
Thomas Scientific Swedesboro, NJ 08085-0099 U.S.A. Wiley Laboratory Mill, Model 4 3375-E10 (115 V, 50/60 HZ) USE AND CARE OF CATALOG NUMBER: 3375-E10 Wiley Laboratory Mill, Model 4 (115 V, 50/60 HZ) UNPACKING
More informationUrea/Adblue Hose Reel
www.scintex.com.au sales@scintex.com.au Model: SHR3408 Urea/Adblue Hose Reel Product Manual Specifications Spring driven drum: for automatic rewind. Locking ratchet: to maintain the desired length of hose
More informationInstallation and User s Manual 12 x 10 MOTORIZED AWNING
12 x 10 MOTORIZED AWNING Installation and User s Manual 12 x 10 MOTORIZED AWNING 088-1763-0 Stop Please read and understand this manual before any assembly or use of this product. Before beginning assembly
More informationINSTANT GARAGE MODEL NO: CIG81224 ASSEMBLY INSTRUCTIONS PART NO: ORIGINAL INSTRUCTIONS
INSTANT GARAGE MODEL NO: CIG81224 PART NO: 3503578 ASSEMBLY INSTRUCTIONS ORIGINAL INSTRUCTIONS GC1117 INTRODUCTION Thank you for purchasing this CLARKE Instant Garage. When erected, the CIG81224 garage
More informationApple Watch Screen Replacement
Apple Watch Screen Replacement Replace the screen (OLED display + digitizer) on your Apple Watch. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION Cracked
More informationFOSC 400 A8/B8 Closure
FOSC 400 A8/B8 Closure I N S T A L L A T I O N I N S T R U C T I O N For Fiber Optic Splices, Taps, and Drops 1.0 General Product Description The FOSC 400 A8/B8 fiber optic closure is environmentally sealed
More informationGT370 HEDGETRIMMER TYPE
GT370 HEDGETRIMMER TYPE 1 Introduction Exploded Drawing Bill Of Material Repair Instructions E13791 GT370-----A New Parts Wiring Diagram Main Menu 44 18 02-04 SEAN HOLDEN GT370 MANUFACTURING PLANT USTI
More informationSOFT TOP ROOF TENT INSTRUCTION MANUAL
SOFT TOP ROOF TENT INSTRUCTION MANUAL CONTENTS SET UP INSTRUCTIONS: 1. INSTALLING YOUR ROOF TOP TENT P2-3 2. SETTING UP YOUR ROOF TOP TENT P4 3. PACKING DOWN YOUR ROOF TOP TENT P5-6 4. TIPS & TRICKS P7
More informationGeneral Purpose Shelter
General Purpose Shelter 0' x 0' x ' ( x x. m) ASSEMBLY MANUAL Model NO.: - Tools required for assembly (not included) TM TABLE OF CONTENTS Important safety instructions... Intended use... Parts list......
More informationASSEMBLY GUIDE. Customer Service: INCH² 2-BURNER & 864 INCH² 2-BURNER
ASSEMBLY GUIDE 688 INCH² 2-BURNER & 864 INCH² 2-BURNER DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open lid. 4. If odor continues, keep away from the appliance
More informationINSTALL INSTRUCTIONS for VEHICLES
INSTALL INSTRUCTIONS for VEHICLES Issued: 1 st December 2011 These are the recommended steps for installing One Way Vision (OWV) film onto a vehicle rear windscreen or side glass panels. Location: Applicable
More informationSTEALTH PRO OWNER S MANUAL
STEALTH PRO OWNER S MANUAL ALWAYS WEAR A COAST GUARD APPROVED FLOTATION DEVICE WHEN OPERATING THE STEALTH PRO. Know the limits of your abilities and the limits of your equipment. Changes in air temperature
More informationVEPR Round Drum Disassembly and Assembly
VEPR 12 25 Round Drum Disassembly and Assembly Required Tools ¼ Allen Wrench Flat Head Screwdriver Drum Parts List Drum Body Carousel Center Bolt Dummy Rounds Carousel Lock Spring Clear Drum Cover Step
More informationAdvantage Plus TIM-3600 Series Reel
Read the following precautions and instructions before you begin assembly or using. Failure to comply with these instructions could result in personal injury or property damage. Keep these instructions
More informationContents. Introduction...3 Description...3. Pack Contents...4. Rada Heavy Duty EV Shower Fittings Right Angled Connector (RAC)...
SHOWER FITTINGS PRODUCT MANUAL IMPORTANT Installer: This manual is the property of the customer and must be retained with the product for maintenance and operational purposes. Contents Introduction...3
More informationRetractable Hose Reel
Retractable Hose Reel installation and Operation Please read before use We recommend keeping these instructions for future reference Hose Reel must be mounted before use Keep the hose retracted when not
More informationOperating Instructions
Operating Instructions OVERVIEW Read the Before You Begin section on page 11 of the ProFiller 3700/3800 Manual v 1.2.1 before using this machine. A. ORIENTATION OF OUTER CAPSULES Orient the capsules as
More informationCABLE CUTTING, STRIPPING AND CRIMPING TOOLS
Cutting 38-39 Stripping 39 0 - CBE CUTTING, STRIPPING ND CRIMPING TOOS Ergonomic handles Surface protection High precision Flexibility With ergonomic handles and a specially The pliers are made of excellent
More informationDarkly LabsR AIR-ASSIST. Installation Manual. English. Deutsch. Emblaser 2 Air-Assist Installation Manual 1.3
Darkly LabsR AIR-ASSIST Installation Manual English Deutsch Emblaser 2 Air-Assist Installation Manual 1.3 1. WHATS IN THE BOX Air-Assist pump Nozzle Bracket Nozzle Air-Assist pump with bracket, Nozzle
More informationJARVIS. Model 70 Airsnip Air Powered Scissors
Air Powered Scissors EQUIPMENT SELECTION... Ordering No. Airsnip Model 70... 4019009 Air Filter/Regulator/Lubricator.. 3022003 Balancer... 1350084 Power--Pak (250 PSI)... 4026016 TABLE OF CONTENTS... Page
More informationFluke Networks offers a wide range of network installation tools each one designed to streamline the network installation job
Insert Section Name Tools and Test Kits Fluke Networks offers a wide range of network installation tools each one designed to streamline the network installation job Fluke Networks offers the most reliable
More informationItem #: BTOT Assembly Instructions
Item #: BTOT Assembly Instructions For our most current instructions, to request missing, lost or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com
More informationINSTALLATION INSTRUCTIONS TOWNSEND
INSTALLATION INSTRUCTIONS TOWNSEND.00 DECK MOUNT BATH FILLER.0 Thank you for selecting American Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-please
More information3D Printed Glider instructions
3D Printed Glider instructions For more cool designs, check out threedsy.com! Printing Instructions: ABS or PET is preferred for durability. Bed must be leveled and printer adjusted to produce good single
More information