12x12 MATRIX LED DRIVER

Transcription

1 x MATRIX LED DRIVER DESCRIPTION The ISFL77 is a general purpose LEDs matrix driver with / cycle rate. The device can be programmed via an IC compatible interface. Each LED can be dimmed individually with 8-bit PWM data which allowing 6 steps of linear dimming. ISFL77 features Auto Breathing Modes which are noted as ABM-, ABM- and ABM-. For each Auto Breathing Mode, there are timing characters which include current rising / holding / falling / off time and loop characters which include Loop-Beginning / Loop-Ending / Loop-Times. Every LED can be configured to be any Auto Breathing Mode or PWM mode individually. FEATURES Supply voltage range from.7v to.v Programmable (8 RGBs) matrix size with de-ghost function Auto Breath Modes and PWM Mode Auto breath offers 8 steps gamma current, interrupt and state look up registers 6 steps global current setting Individual PWM control 6 steps Individual open and short error detect function QFN-0 (6mm 6mm) package RECOMMENDED EQUIPMENT.0V, A power supply ABSOLUTE MAXIMUM RATINGS.V power supply Caution: Do not exceed the conditions listed above, otherwise the board will be damaged. PROCEDURE The ISFL7 evaluation board is fully assembled and tested. Follow the steps listed below to verify board operation. Caution: Do not turn on the power supply until all connections are completed. ) Short J to connect VO and. ) Short J to connect P and U. ) Connect the VDC power to the connector (J&J). ) Turn on the power supply/plug in the Micro USB Pay attention to the supply current. If the current exceeds A, please check for circuit fault. QUICK START Figure : Photo of ISFL77 Evaluation Board ORDERING INFORMATION Part No. Temperature Range Package ISFL77-QFLS-EB -0 C to + C (Industrial) QFN-0, Lead-free Table : Ordering Information For pricing, delivery, and ordering information, please contacts ISSI s analog marketing team at analog@issi.com or (08) Integrated Silicon Solution, Inc. Rev. A, 07/6/06

2 x MATRIX LED DRIVER EVALUATION BOARD OPERATION The ISFL77 evaluation board has three animation display modes. Press K to switch configurations. ) Line- rotate animation ) Money animation ) Butterfly animation ) All led turn on Note: ISFL77 solely controls the FxLED function on the evaluation board. SOFTWARE CONTROL J default setting is closed (short). If it is set to open, the U (LDO) will stop working and all the V, including the supply of MCU will be cut off, all the MCU's IO will be high impedance (open-drain) and external control is allowed. The ISFL77 can set its IC bus interface logic threshold based on the voltage on the pin. An external voltage in the range of.8v can be applied after removing (open) the J jumper. The board comes with J default setting closed (short). If it is set to open, the user can connect an external voltage supply, the external voltage is recommended to equal to ex-iic s high logic. Follow the steps listed below for external control. ) Open J to disconnect the power of U, disable the V0 (.0V). ) Open J to disconnect the to V0, and connect an external MCU to. ) Pull-up the SDB to. ) Connect the VDC power to the connector (J&J). ) Turn on the power supply/plug in the Micro USB Pay attention to the supply current. If the current exceeds A, please check for circuit fault. 6) Start external IIC control. Caution: If J is closed (shorted), user can t connect the user s MCU to directly, otherwise the user s MCU (maybe.8v) will connect to evaluation bard s (.0V) and maybe damaged. Please refer to the datasheet to get more information about ISFL77. Integrated Silicon Solution, Inc. Rev. A, 07/6/06

3 x MATRIX LED DRIVER MCU C 0uF C7 0uF C0 0.uF C 0.uF V R0 NC R9 00K C 0.uF C 0.uF SDB_RGB INTB SCL_RGB SDA_RGB SYNC R R R7 00K 7K 00K P P A SDB INTB SCL SDA IICRS SYNC REST ADDR P P A U IS77 SW SW SW SW SW SW6 SW7 SW8 SW9 SW0 SW SW CS CS CS CS CS CS6 CS9 CS0 CS CS CS CS SW SW SW SW SW SW6 SW7 SW8 SW9 SW0 SW SW CS CS CS CS CS CS6 CS7 CS8 CS9 CS0 CS CS V R 6K R 9K k R 0K U VBAT VDD_ PC-ANTI_TAMP VSS_ PC-OSC_IN PB9/TIM_CH PC-OSC_OUT PB8/TIM_CH OSC_IN OSC_IN BOOT0 OSC_OUT 6 OSC_OUT PB7/IC_SDA/TIM_CH 7 NRST PB6/IC_SCL/TIM_CH 8 VSSA PB V 9 VDDA PB/JNTRST 0 PA0-WKUP/ADC_IN0/TIM_CH_ETR PB/JTDO PA/ADC_IN/TIM_CH PA/JTDI PA/USART_TX/ADC_IN/TIM_CH PA/JTCK/SWCLK PA/USART_RX/ADC_IN/TIM_CH VDD_ SPI_CS PA/SPI_NSS/ADC_IN VSS_ SPI_CLK PA/SPI_SCK/ADC_IN PA/JTMS/SWDIO SPI_MISO 6 PA6/SPI_MISO/ADC_IN6/TIM_CH PA/CANTX/USBDP/TIM_ETR SPI_MOSI 7 PA7/SPI_MOSI/ADC_IN7/TIM_CH PA/CANRX/USBDM/TIM_CH 8 PB0/ADC_IN8/TIM_CH PA0/USART_RX/TIM_CH 9 PB/ADC_IN9/TIM_CH PA9/USART_TX/TIM_CH 0 PB/BOOT PA8/TIM_CH/MCO PB0/IC_SCL/USART_TX PB/SPI_MOSI/TIM_CHN PB/IC_SDA/USART_RX PB/SPI_MISO/TIM_CHN VSS_ PB/SPI_SCK/TIM_CHN V VDD_ PB/SPI_NSS/TIM_BKIN STMF0C8T6 C uf V M-SDA M-SCL CLK V DIO USB_DP USB_DM SDB M-INTB V Power U U VDD VOUT C SD uf C BP 0nF LDO V C uf OSC C OSC_OUT P Y 8M C6 OSC_IN P CLK DIO.V IICRS SYNC INTB SDA SCL AD AD SCL SDA P SDB CON V J +V D J DFLS0 D Header H DFLS0 NC P P U J J Header H Micro USB FLASH M-SDA M-SCL R K R6 K M-SDA M-SCL R USB_DM R R USB_DP R R.V.K +V USB_DM USB_DP CON C8 0.uF SPI_CS SPI_MISO U CE SO WP HOLD SCK SI SPI_CLK SPI_MOSI C9 0.uF M-INTB R8 00K M-INTB ISLQ0C LED Array CS8 CS7 CS6 CS CS CS CS CS SW LD77 LD78 LD79 LD80 LD8 LD8 LD8 LD8 CS CS CS0 CS9 LD8 LD86 LD87 LD88 SW LD6 LD6 LD6 LD6 LD6 LD66 LD67 LD68 LD69 LD70 LD7 LD7 SW0 LD LD6 LD7 LD8 LD9 LD0 LD LD LD LD LD LD6 SW9 LD9 LD0 LD LD LD LD LD LD6 LD7 LD8 LD9 LD0 SW8 LD LD LD LD6 LD7 LD8 LD9 LD0 LD LD LD LD SW7 LD97 LD98 LD99 LD00 LD0 LD0 LD0 LD0 LD0 LD06 LD07 LD08 SW6 LD8 LD8 LD8 LD8 LD8 LD86 LD87 LD88 LD89 LD90 LD9 LD9 SW LD6 LD66 LD67 LD68 LD69 LD70 LD7 LD7 LD7 LD7 LD7 LD76 SW LD9 LD0 LD LD LD LD LD LD6 LD7 LD8 LD9 LD60 SW LD LD LD LD6 LD7 LD8 LD9 LD0 LD LD LD LD SW LD7 LD8 LD9 LD0 LD LD LD LD LD LD6 LD7 LD8 SW LD LD LD LD LD LD6 LD7 LD8 LD9 LD0 LD LD Figure : ISFL7 Application Schematic Integrated Silicon Solution, Inc. Rev. A, 07/6/06

4 x MATRIX LED DRIVER BILL OF MATERIALS Name Symbol Description Qty Supplier Part No. LDO U Reduced voltage SGMICRO SGM09-.V MCU U Microcontroller STM STMF0C8T6 LED Driver U Matrix LED Driver ISSI ISFL7 Flash U Flash ISSI ISLQ0C Diode LD~LD9 Blue LED, SMD Everlight 9-7/BHC-ZLMRY/T Diode D,D Diode, SMD DIODES DFLS0 Crystal Y Crystal, 8MHz JB HC-9S Resistor R7,R8, R9,R RES,00k,/6W,±%,SM D Yageo RC060JR-0700KL Resistor R,R RES,R,/6W,±%,SMD Yageo RC060JR-07RL Resistor R RES,0k,/6W,±%,SMD Yageo RC060JR-070KL Resistor R RES,.k,/6W,±%,SMD Yageo RC060JR-07KL Resistor R RES,7k,/6W,±%,SMD Yageo RC060JR-077KL Resistor R6,R RES,k,/6W,±%,SMD Yageo RC060JR-070KL Resistor R RES,6k,/6W,±%,SMD Yageo RC060JR-076KL Resistor R RES,9k,/6W,±%,SMD Yageo RC060JR-079KL Resistor R0 NC Yageo Capacitor C,C,C CAP,µF,6V,±0%,SMD Yageo CC060KKX7R9BB0 Capacitor C CAP,0nF,6V,±0%,SMD Yageo CC060KKX7R9BB00 Capacitor C,C7 CAP,0uF,6V, ±0%,SMD Yageo CC060KKX7R9BB06 Capacitor C6,C CAP,pF,6V,±0%,SMD Yageo CC060KKX7R9BB0 Capacitor C8,C9,C0,C,C,C CAP,0.µF,6V,±0%,SMD 6 Yageo CC060KKX7R9BB0 Button K Button SMD Bill of Materials, refer to Figure above. Integrated Silicon Solution, Inc. Rev. A, 07/6/06

5 x MATRIX LED DRIVER Figure : Board Component Placement Guide - Top Layer Figure : Board PCB Layout - Top Layer Integrated Silicon Solution, Inc. Rev. A, 07/6/06

6 x MATRIX LED DRIVER Figure : Board Component Placement Guide - Bottom Layer Figure 6: Board PCB Layout - Bottom Layer Integrated Silicon Solution, Inc. 6 Rev. A, 07/6/06

7 x MATRIX LED DRIVER Figure 7: LED Board Component Placement Guide - Top Layer Figure 8: LED Board PCB Layout - Top Layer Integrated Silicon Solution, Inc. 7 Rev. A, 07/6/06

8 x MATRIX LED DRIVER Figure 9: LED Board Component Placement Guide - Bottom Layer Figure 0: LED Board PCB Layout - Bottom Layer Copyright 06 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. 8 Rev. A, 07/6/06

9 x MATRIX LED DRIVER REVISION HISTORY Revision Detail Information Date A Initial release Integrated Silicon Solution, Inc. 9 Rev. A, 07/6/06