Heavy Duty Instant Garage 3.0m x 6.1m x 2.4m / 10' x 20' x 8' Assembly Manual

Size: px

Start display at page:

Download "Heavy Duty Instant Garage 3.0m x 6.1m x 2.4m / 10' x 20' x 8' Assembly Manual"

Coleen Manning
6 years ago
Views:

1 Heavy uty Instant Garage 3.0m x 6.1m x 2.4m / 10' x 20' x 8' ssembly Manual SRIPTION MOL # Heavy uty Instant Garage Grey 3.0m x 6.1m x 2.4m / 10' x 20' x 8' IG ROMMN TOOLS + 18" /- 45 cm 7/16" 11mm Please read instructions OMPLTLY before assembly. This shelter MUST be securely anchored. Before you start: 2 or more individuals recommended for assembly. larke International Hemnall Street pping ssex M16 4LG NGLN Page 1 PRTS & SRVI: mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SLS: UK or XPORT: (0)

2 TTNTION: This shelter product is manufactured with quality materials. It is designed to fit the garage custom fabric cover included. Please anchor the garage carefully following the instructions in the manual. Proper anchoring, keeping cover tight and free of snow and debris is the responsibility of the consumer. Please read and understand the installation detail, warnings and cautions prior to beginning installation. NGR: hoose the location of your garage carefully. NGR: Keep away from electrical wires. heck for overhead utility lines, tree branches or other structures. heck for underground pipes or wires before you dig. O NOT install near roof lines or other structures that could shed snow, ice or excessive run off onto your shelter. O NOT hang objects from the roof or support cables. WRNING: Risk of fire. O NOT smoke or use open flame devices (including grills, fire pits, deep fryers, smokers or lanterns) in or around the garage. O NOT store flammable liquids (gasoline, kerosene, propane, etc.) in or around your shelter. o not expose top or sides of the shelter to open fire or other flame source. UTION: Use UTION when erecting the frame. PROPR NHORING N INSTLLTION O RM: PROPR NHORING O TH RM IS TH RSPONSIBILITY O TH ONSUMR. larke International is not responsible for damage to the unit or the contents from acts of nature. ny garage that is not anchored securely has the potential to fly away causing damage. Periodically check the anchors to ensure stability of the garage. larke International cannot be responsible for any shelter that blows away. NOT: Your shelter s cover can be quickly removed and stored prior to severe weather conditions. If strong winds or severe weather is forecast in your area, we recommend removal of cover. R N LNING: tight cover ensures longer life and performance. lways maintain a tight cover. Loose fabric can accelerate deterioration of cover fabric. Immediately remove any accumulated snow or ice from the roof structure with a broom, mop or other soft-sided instrument. Use extreme caution when removing snow from cover- always remove from outside the structure. O NOT use hard-edged tools or instruments like rakes or shovels to remove snow. This could result in punctures to the cover. O NOT use bleach or harsh abrasive products to clean the fabric cover. over is easily cleaned with mild soap and water. Page 2

3 PRTS LIST x4 x10 x x38 x x8 x48 x x12 x x x x1 x1 x x x x6 x10 x16 x96 B B x x10 x2 x4 x6 x14 x4 x4 x8 x Page 3

4 1. SSMBL 2 N RIBS Secure connections using Bolts as shown with # Nuts # # # SSMBL 3 MIL RIBS NOT: The bolt heads at the end ribs must be facing outward to avoid damaging your cover # # # Page 4

5 3. ONNT RONT N RIB TO 1 MIL RIB. ssemble 2 Side ross s using parts as shown. B. ssemble 1 Top ross using parts as shown.. ssemble 2 over s using parts as shown. onnect the 2 Side ross s at the stabiliser.. onnect the Top ross at the 3- and 4-Way onnectors as shown.. Place a over at each leg and secure it with a over lamp as shown. Slide the over s so they are 8 inches up from the ground. Only HN-TIGHTN these bolts! ssemble Side ross s ssemble Top ross B B ross nd Rib ssemble over s Middle Leg over over No Bolt at this connection Page 5

6 4. ONNT RMINING RIBS. ssemble 2 Side ross s using parts as shown. B. ssemble 1 Top ross using parts as shown.. ssemble 2 over s using parts as shown. onnect the 2 Side ross s at the stabiliser.. onnect the Top ross at the 3- and 4-Way onnectors as shown.. Place a over at each leg and secure it with a over lamp as shown. Slide the over s so they are 8 inches up from the ground. Only HN-TIGHTN these bolts! ssemble Side ross s ssemble Top ross B nd Rib Middle Rib ross ross Middle Rib nd Rib over ssemble over s over over No Bolt at this connection Page 6

7 5. SQURING UP TH RM. Place frame in its final location, which needs to be as flat and level as possible. B. Measure across opposite corners. These distances must be equal to within 1 inch.. heck that the front and rear of the frame measures 10 feet in width. 10 ft. 10 ft. 6. PROPRLY NHOR TH RM. nchors must be placed inside shelter at the corners of the shelter. B. Insert a ¾-inch pipe or steel rod, through the eyelet of the auger and screw the anchor into the ground until the eyelet is sticking out of the ground by 1 to 2 inches so it can be anchored to the legs. If ground is too hard, dig a hole with a shovel or post hole tool. Optional: ill with cement.. Wrap cable provided through the eyelet of the anchor and around the frame as shown below. Secure the cable with the clamps provided. NOT: or best results use "asy Hook nchoring System" (Model No. GH1, Part No ). vailable from your dealer nd Rib nchors WRNING: Serious injury to persons or property could result if cover is installed and shelter is not anchored and is left unattended. Shelter must be securely anchored before use. Page 7

8 7. OOR PNL N BK PNL INSTLLTION. (1) Hold end panel at the top center with white inner surface facing inside of the shelter. (2) Wrap the edges of the fabric panel around the end rib and line up the cross rails with the pre made slits in the fabric. 1 2 B. (1) isconnect top cross rail (the horizontal pipe that runs from front to back along the top) from the end rib. (2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel. (3) Reattach the top cross rail to the end rib. B1 B2 B3. (1) isconnect side cross rail from the end rib. (2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel. (3) Reattach the side cross rail to the end rib Page 8

9 7. N PNL INSTLLTION - continued. t the bottom, where the webbing exits the pocket on each side of end panel, pull webbing as you would a drawstring to remove the slack. Be careful not to pull the webbing strap out of the webbing pocket. N PNL VIW ROM INSI WBBING STRP PULL PULL. Insert the S - Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet and pull tight. Wind the ratchet so that the webbing overlaps itself. Position the end panel so that it is centered on the building before fully tightening the end panel.. Tighten ratchets, alternating from one side to the other, until the end panel is tight. NOT: Keep zippers closed when tightening door panel. Insert Webbing into Ratchet Page 9

10 8. INSTLLING OVR N OVR RILS. Lay the cover on the ground next to the frame with inside of the cover (the side with the pipe pockets) facing down and the webbing on the front and rear of the corner of the building. B. Pull cover over the frame, making sure to center cover on frame. There should be an equal amount of overhang at all four corners.. Insert the S - Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet and pull tight. Wind the ratchet so that the webbing overlaps itself.. isassemble cover rails and slide through fabric pockets at each leg and reattach with clamps to each leg. Repeat this on other side. Push down on cover rails to tighten cover, before tightening bolts completely.. heck and tighten Ratchets and over s monthly to ensure the cover is tight. NOT: The logo should be oriented as shown below. ORRT RONT INORRT RR OVR RILS Webbing and Ratchets Securing over nd Rib ross lamps orner Leg Middle Rib ross lamps Middle Leg The following accessories are available for your garage:- GH1 asy Hook nchoring System (Part No ) G1 4pc 15 uger Securing Set (Part No ) GRU1 Garage Roll Up oor Kit (Part No ) See your nearest larke dealer for more information. Page 10

11 OTHR QULITY LISUR & GRNING PROUTS VILBL ROM LOGBUSTRS BNQUTING TBLS POP-UP NOPIS INSTNT SHS & GRGS PORTBL GNRTORS GRN TROLLYS L HLIGHTS / LSHLIGHTS HOT & OL POWR WSHRS TRPULINS INST KILLRS R OVRS INVRTRS JUMP STRTS OOT PUMPS NS LRS N MUH MOR! PRTS & SRVI: mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SLS: UK or XPORT: (0) Hemnall Street, pping, ssex M16 4LG

14' x 32' x 12' Round Top Round Style Shelter Assembly Instructions

14' x 32' x 12' Round Top Round Style Shelter Assembly Instructions Description Model # 14' x 32' x 12' RoundTop Garage - Gray 62669 Recommended Tools Please read instructions COMPLETELY before assembly.